MiniBoss MB-S1 Three Wheel Kids Kick Scooter User Manual
- June 5, 2024
- MiniBoss
Table of Contents
MiniBoss MB-S1 Three Wheel Kids Kick Scooter
warning :
- It is not suitable for children under 3 years old.
- It is not suitable for children weighing more than 60kg.
- Please wear protective equipment while driving.
- It should not be used on public transportation roads.
- It is recommend to use protective equipment such as helmets, gloves, knee pads and elbow pads.
- Please be careful when using scooters, and strictly abide by safety signs and traffic regulations.
- before use, please check the scooter and make sure all the locks, components, hooks, and screws are locked. Also check the wear of the wheel.
- Small parts are included, please be assembled or disassembled by adults.
- The scooters must be assembled and debugged by adults before being used by children, and must be used under the supervision of adults.
Note:
- Please be cautious cause of the scooters have certain risks.
- Please master the basic skills of taxing, turning and braking.
- Please use the scooter cautiously, do not ride too fast to avoid falling or hitting others. Avoid all dangerous actions.
- The brake system of the scooter can not provide safety protection for downhil driving, please avoid sliding when going downhill.
- The mudguard will heat up while we driving the scooter. Do not touch the mudguard to prevent burns at this moment.
- Never drive a scooter by more than one person.
- Do not use the scooter in rainy, nighttime and low visibility weather or dim environment.
- Do not drive it on wet, oil, sand, ice, rugged or uneven ground.
- Do not replace any components on the scooter so as not to affect security.
- Loosen the screw repeatedly will reduce the tightening of the screw and cause the screw to unsecured. If the screw is loose, it must be purchased again.
Product Description
- The overall handlebar stem made by aluminum alloy and C-shaped curve design fit perfectly with the grip angle of human. The T-shaped stem completely wraps the metal section to avoid possible bumps and scratches, giving the child more protection.
- It has superior load-bearing capacity with a large pedal design. Equipped with Ranti-slip technology to ensure a better driving performance.
- The wheels are dual-mode designed for free switching, meet the different needs of children at all stages.
- The integrated design avoids the safety hazard caused by structural exposure, also it is more safe, trendy and easier to clean.
- By the design of large and flashing PU wheel, enhanced the driving performance.
Packing list
Assembly and Use
Assemble Components
Turn the button of handlebar stem towards the front direction and secure it into the mounting hole until it sounds a ‘pa’ which indicates that the lock is in place. Pull the handlebar stem in the opposite direction and confirm that the orange locking hook can be seen from the bottom plate to ensure safe locking.
Raise and Lower the Handlebar Height
Loosen the locking sleeve, the handlebar stem can be adjusted up and down three gears, select the appropriate height and make the hoodle pop out from the hoodle hole. Then tighten the locking sleeve (make sure the hoodle pops out from the hoodle hole when using, and the locking sleeve has locked). The minimum height is 600mm and the maximum height is 780mm.
Driving and Turing
The scooter controls turning direction of the front wheel by tilting the center of gravity, and the directional control can be achieved by tilting left and right of the handlebar while driving.
Brake System
The brake system can be operated by pressing the mudguard of the scooter with
your foot.
Note! The mudguard will heat up when the brake system is running. Please
do not touch it to avoid burns.
Switching Mode of Wheel
Disassemble the two pairs of lock screws on the stand, adjust the front wheel towards to the angle of mounting hole, and adjust the direction of the hole plug. Lock the screw to switch the two mode of the wheel (as shown in the figure above). It drives slowlv on tilt mode which is not easv to rollover andhas stronaer
Maintenance
After use, it is recommend to clean the scooter and components by soft cloth, and oil the axle bearing regularly, even please replace the axle bearing if necessary.