CRICKET SPEAKER Stem Mount Bicycle System User Manual
- June 5, 2024
- CRICKET SPEAKER
Table of Contents
USER MANUAL
The CRICKET SPEAKER stem mount bicycle system is meant to work with your Bluetooth device to provide hours of responsible, listening pleasure while you are on the trail.
Installation Instructions
The Cricket Speaker system comes with an aluminum stem cap that replaces your
bicycle stem cap.
Important: Do not loosen the 2 horizontal bolts that clamp your stem on
the steering tube.
-
Remove the current stem cap by removing the Allen-head bolt in the center of the stem cap.
-
Position the Cricket Speaker stem cap with the threads facing up, centered on the steer tube.
-
Gently tighten the provided bolt through the center to hold the stem cap in place. Do not overtighten. The final rotational orientation of the stem cap will affect the final product orientation. Adjust to your liking if desired.
Note: This should not affect steering tension because the two horizontal bolts have remained in place. -
Position the Sealing Skirt over the Cricket Speaker so that the USB Charging port is completely covered.
-
Thread the speaker onto the Cricket Speaker stem cap until it gently bottoms out. Do not overtighten. Ensure the edges of the skirt sit in the groove on the stem cap while tightening. GO-RIDE!
Charging your Cricket Speaker
- Remove the sealing skirt from the Cricket Speaker.
- Connect the micro USB connector from the cable to the Cricket Speaker.
- Plug the USB connector into a USB-compatible wall charger (ideally with a 0.3A output and 5V DC)
- When the Cricket Speaker is fully charged (the indicator light will change from red to green) disconnect the USB cable.
Playing Audio from your Cricket Speaker
- Power the Cricket Speaker on by pressing and holding the top of the speaker down for 3 seconds. The Cricket Speaker will be ‘discoverable’.
- On your Bluetooth device, search for ‘Cricket’ in the list of devices and pairs.
- Once paired, play your music on your Bluetooth device.
**** Pressing the top of the speaker down will ‘Pause’ and ‘Resume’ the musk playback.
Answering Calls from your Cricket Speaker
Pressing down on the top of the Cricket Speaker will answer an incoming call. Pressing again will end the call.
REACHING OUT TO US
www.cricketspeakencom cricket_speaker on
Instagram Cricket Speaker on Facebook
or on the trails of Arizona!
TECHNICAL SPECIFICATIONS
| Input | 5V / 0.3A |
|---|---|
| Output | 2W |
| Capacity | 350 mAh |
| Charge Time | – 2 – 3 hours |
| Playtime | – 4 hours @ 50% volume |
| Operating Distance | – 10 meters max |
| Bluetooth version | Bluetooth 5.0 with EDR |
| Dimensions | 040mm x 41mm |
| Protection | Water and Dust Resistant (do not submerge) |
| Net Weight | 52 g |
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. Suppose this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on. In that case, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver. a
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.