GARMIN 010-02466-00 Power Switch Digital Switch Box Owner’s Manual

GARMIN 010-02466-00 Power Switch Digital Switch Box

Getting Started

WARNING
See the Important Safety and Product Information guide in the product box for product warnings and other important information.

CAUTION
Garmin® strongly recommends having an experienced installer with proper knowledge of electrical systems install the device. Incorrectly wiring the power cables can result in damage to the device, the vehicle, or the battery, and can cause bodily injury.

NOTICE
Disconnect the negative battery terminal in the vehicle before installing the device to prevent an electrical short circuit. Reconnect the vehicle battery terminals only after installation is complete.

1 Mount the device (Mounting Considerations, page 1).
2 Connect accessories to the device (Connecting Accessories, page 2).
3 Connect a control input (optional) (Connecting a Control Input, page 2).
4 Connect the device to vehicle power (Connecting the Device to Vehicle Power, page 2).
5 Pair your device with a compatible Garmin navigation device (Pairing with a Garmin Navigation Device, page 2) or a smartphone (Pairing with Your Smartphone, page 3).

Device Overview

Installation

Mounting Considerations

•  The device must be mounted close to the battery and within the range of the supplied power cable.
•  The mounting surface must be strong enough to support the weight of the device.
•  The location must allow room for the routing and connection of all cables.

Mounting the Device
Before you can mount the device, you must select a mounting location and purchase the appropriate hardware for your mounting surface.

NOTICE
Avoid wires, gauges, air bags, air bag covers, HVAC, and other items when drilling pilot holes and attaching the mount to the vehicle. Garmin is not responsible for any damages or consequences arising from the installation.

1.  Place the mount on the selected location.

2.  Using the mount as a template, mark the two screw locations

3.  Drill pilot holes (optional).
   For some types of mounting material, drilling pilot holes is necessary. Do not drill through the mount.

4.  Securely fasten the mount to the surface using the appropriate hardware for your mounting surface.

Opening the Front Cover

You must open the front cover to make electrical connections.

1.  Lift the front cover latch and rotate it counter-clockwise.
2.  Pull the front cover off of the device.

Connecting Accessories

NOTICE
Do not use the device to control or power a winch. Failure to follow this notice could cause damage to your vehicle or your device.

Accessory requirements:

•  Verify the amperage rating of each accessory before wiring it to the Garmin PowerSwitch device. The device supports accessories up to 30 A for each channel and a maximum of 100 A for the entire system.
•  Use 10 AWG (6 mm2) wires for accessories that use 20 to 30 A.
•  Use 12 AWG (4 mm2) wires for accessories that use 10 to 20 A.
•  Use 14 AWG (2.5 mm2) wires for accessories that use less than 10 A.
•  Use the appropriate size terminals for all accessory connections.
•  Crimp all terminal connectors securely.

1.  Connect the positive wire from the accessory to one of the accessory terminals on the Garmin PowerSwitch device.

2.  Connect the negative or ground wire to an unpainted ground stud on the vehicle frame, to a ground distribution block, or directly to the negative terminal on the battery.
   NOTICE: Do not connect the accessory ground wires to the ground terminal (GND) on the Garmin PowerSwitch device. Failure to heed this notice could result in personal or property damage, or negatively impact device functionality.

3.  Verify that all electrical connections are tight and will not come loose during use.

Connecting a Control Input

You can connect to the control terminals to enable the Garmin PowerSwitch device to turn on customizable outputs. For example, you can connect your vehicle ignition switch to a control input terminal to turn on accessories automatically each time you start your vehicle. The control terminals detect a signal from 3.3 V to 18 V. You can configure output functions with the Garmin PowerSwitch app. Connect the control wire from the control source in your vehicle to one of the two control terminals on the Garmin PowerSwitch device.

Connecting the Device to Vehicle Power

Before you can connect the device to vehicle power, you must remove the warning tag from the +12V terminal on the device.
You should always confirm all electrical connections are secure and will not come loose while operating the device.

1.  Connect the large ring end of the included ground wire to the negative terminal on the vehicle battery.

2.  Connect the small ring end of the ground wire to the GND terminal on the device.

3.  Connect the small ring end of the included 12V cable to the +12V terminal on the device.

4.  Tighten the 3/8 in. nut on the +12V terminal to a maximum torque specification of 4.52 N-m (40 lbf-in.). You should confirm the nut cannot be loosened by hand.
   NOTICE Do not overtighten the +12V terminal to prevent damage to the terminal.

5.  Connect the large ring end of the 12V cable to the positive terminal on the vehicle battery.

Pairing and Setup

Pairing with a Garmin Navigation Device

You can pair your Garmin PowerSwitch device with a compatible Garmin navigation device.

1.  Turn on power to your Garmin PowerSwitch device, and place your compatible Garmin navigation device within 1 m (3.3 ft.) of it.
2.  On your compatible navigation device, open the Garmin PowerSwitch app.
3.  Follow the on-screen instructions to complete the pairing and setup process.

The main app dashboard appears. After the devices are paired, they connect automatically when they are turned on and within range.

Pairing with Your Smartphone

You can pair your Garmin PowerSwitch device with your smartphone and the Garmin PowerSwitch app to enable wireless digital switching.

1.  From the app store on your smartphone, install the Garmin PowerSwitch app.
2.  Turn on power to your Garmin PowerSwitch device, and place your smartphone within 1 m (3.3 ft.) of your device.
3.  On your smartphone, open the Garmin PowerSwitch app.
4.  Follow the on-screen instructions to complete the pairing and setup process.
   The main app dashboard appears. After the devices are paired, they connect automatically when they are turned on and within range.

Pairing an Additional Garmin PowerSwitch Device

You can pair an additional Garmin PowerSwitch device with your smartphone or navigation device.

1.  From the Garmin PowerSwitch app, select Settings > Add Another Device.
2.  Follow the on-screen instructions to complete the pairing and setup process.

Garmin PowerSwitch App

Activating a Power Switch

Before you can use the Garmin PowerSwitch app to activate a switch, you must install your Garmin PowerSwitch device in your vehicle and pair it with the Garmin PowerSwitch app. From the Garmin PowerSwitch app, select a power button to turn a switch on or off.

Turning Off All Switches

Select Off.

Customizing a Button

•  From the Garmin PowerSwitch app screen, select Edit. The app enters editing mode.
•  Select on the button you want to customize.
•  Select an option:
  •  To change the name of the button, select the Button Label field, and enter a name.
  •  To add an icon to the button, select the Icon field, and select an icon.
  •  To change the button color, select a color.
  •  To change the button mode, select a button mode.
  •  To adjust the intensity of the switch, use the slider.
  •  To set the button to activate with a control input, select a control input.
•  Select .
•  Select Done.

Assigning a Switch to a Control Input

Before you can use control input functions, you must connect a control input to your Garmin PowerSwitch device (Connecting a Control Input, page 2). You can assign one or more switches to turn on when the Garmin PowerSwitch device receives a signal from a control input.

1.  Select Settings.
2.  Select your Garmin PowerSwitch device.
3.  Select a control input.
4.  Select one or more switches.

Adding a Custom Layout

You can add a custom layout tab to the Garmin PowerSwitch app. Buttons added to a custom layout can control multiple switches at the same time.

1 From the Garmin PowerSwitch app, select Edit. The device enters editing mode.
2 Select .

Adding a Button to a Custom Layout

1.  From the Garmin PowerSwitch app, select a custom layout tab.
2.  Select Edit. The app enters editing mode.
3.  Select Add Button.
4.  On the new button, select .
5.  Select an option:
6.  To change the name of the button, select the Button Label field, and enter a name.
7.  To add an icon to the button, select the Icon field, and select an icon.
8.  To change the button color, select a color.
9.  Select Add Action.
10.  If necessary, select a Garmin PowerSwitch device and a switch.
11.  Select an action:
12.  To set the button to turn the switch on or off with each press, select Toggle.
13.  To set the button to turn on the switch, select Turn On.
14.  To set the button to turn off the switch, select Turn Off.
15.  Select a button mode:
16.  To set the button to activate with one touch, select Normal.
17.  To set the button to activate only while touching the button, select Momentary.
18.  To set the button to turn on and off repeatedly, select Strobe, and select time intervals.
19. If applicable, use the slider to set the brightness of lights.
20. Select .
21. If necessary, select Add Action to add additional actions for the button. You can add one action for every switch on the Garmin PowerSwitch device.

Arranging Buttons In a Custom Layout

1.  From the Garmin PowerSwitch app, select a custom layout tab.
2.  Select Edit. The app enters editing mode.
3.  On the button you want to move, hold , and drag the button to a new location.

Deleting a Custom Layout or Button

1.  From the Garmin PowerSwitch app, select a custom layout tab.
2.  Select Edit. The app enters editing mode.
3.  Select an option:
4.  To delete a button, select on the button you want to delete.
5.  To delete a layout tab, select on the layout tab.

Routines

Routines automate your Garmin PowerSwitch device. When you define a routine on your compatible Garmin navigation device, it turns switches on or off automatically when the conditions of the routine are met. For example, you can set a routine to turn on a switch at specific time each day or when your vehicle reaches a specific speed. Routines are available only when using a compatible Garmin navigation device.

Adding a Routine

1.  From the Garmin PowerSwitch app, select > Routines.
2.  If necessary, select Add Routine.
3.  Select When.
4.  Select a trigger:
5.  To set a switch to trigger when your vehicle reaches a specific speed, select Speed > Next, and follow the on-screen instructions to enter speed thresholds.
6.  To set a switch to trigger at a specific time each day, select Time > Next, and enter a time.
7.  To set a switch to trigger at sunrise, select Sunrise.
8.  To set a switch to trigger at sunset, select Sunset.
9.  Select Add Action.
10.  Select a device, a switch, an action, and a button mode.
11.  If necessary, use the slider to adjust the dimmer.
12.  Select Save.

Editing a Routine

1.  From the Garmin PowerSwitch app, select > Routines.
2.  Select on the routine you want to edit.
3.  Select an option:
4.  To change the trigger for the routine, select When, and select a trigger.
5.  To change an action, select on the action you want to change, and update the action.
6.  To add an action to the routine, select Add Action, and enter information about the action.
7.  Select Save.

Deleting a Routine

1.  From the Garmin PowerSwitch app, select > Routines.
2.  Select on the routine you want to delete.

Device Maintenance

Garmin Support Center

Go to support.garmin.com for help and information, such as product manuals, frequently asked questions, videos, and customer support.

Device Care

NOTICE
Avoid extreme shock and harsh treatment, because it can degrade the life of the product. Do not use a sharp object to clean the device. Avoid chemical cleaners, solvents, and insect repellents that can damage plastic components and finishes. Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage.

Cleaning the Outer Casing

NOTICE
Avoid chemical cleaners and solvents that can damage plastic components.

1.  Clean the outer casing of the device using a cloth dampened with a mild detergent solution.
2.  Wipe the device dry.

Changing the Fuse in the Vehicle Power Cable

NOTICE
When replacing the fuse, do not lose any of the small pieces and make sure they are put back in the proper position. The vehicle power cable does not work unless it is assembled correctly.
If your device does not receive power in your vehicle, you may need to replace the fuse located on the red power cable.

1.  Pull up the top cover from the top of the in-line fuse assembly.
2.  Using an 8 mm (5/16 in.) wrench, remove the two nuts that secure the two parts of the power cable to the in-line fuse assembly.
3.  Disconnect the power cables.
4.  Remove the fuse from the bottom cover .
5.  Place a new 125 A fuse on the bottom cover.
6.  Reinstall the power cables and nuts.
7.  Tighten the nuts to a maximum torque specification of 2.26 N-m (20 lbf-in.).
8.  Reinstall the top cover.

Updating Device Firmware

The Garmin PowerSwitch app notifies you when firmware updates for your Garmin PowerSwitch device are ready to install. When the update notification appears, follow the on-screen instructions to complete the update process.

NOTE:
Do not disconnect power during the update process.

Restoring Device Settings

The Garmin PowerSwitch app enables you to reset the device to the factory default values.

1.  From the Garmin PowerSwitch app, select Settings.
2.  Select a Garmin PowerSwitch device.
3.  Select Restore Defaults.

Troubleshooting

My Garmin PowerSwitch will not stay connected

•  Verify the Garmin PowerSwitch device is receiving power.
•  Verify that Bluetooth® technology is enabled on your paired navigation device or smartphone.
•  Move the navigation device or smartphone closer to your Garmin PowerSwitch device.
•  Verify that your vehicle’s battery is supplying at least 12 V of power.
  The Garmin PowerSwitch device turns off all outputs automatically to preserve your vehicle’s battery if it is receiving less than 11 V of power (My accessories are not receiving power, page 5).

My accessories are not receiving power

•  Verify the Garmin PowerSwitch device is receiving power from the vehicle battery.
•  Verify that your vehicle’s battery is supplying at least 12 V of power. The Garmin PowerSwitch device turns off all outputs automatically to preserve your vehicle’s battery if it is receiving less than 11 V of power. Outputs turn back on when the device detects more than 12 V of power.
•  Verify that all electrical connections are secure and will not come loose while operating the vehicle.
•  Verify that each connected accessory draws less than 30 A. If an accessory draws more than 30 A, the device turns off that output automatically.
•  Verify that the total system load is less than 100 A. If the device detects a system load of more than 100 A, it turns off all outputs automatically.
•  Inspect all electrical connections for an electrical short circuit.

Can I mount the device in an engine compartment?

You can mount the device in an engine compartment as long as the temperature of the engine compartment does not exceed 85°C (185°F) . Do not mount the device near a turbocharger or an exhaust manifold.

Can the device get wet?

The device is designed to operate in wet conditions, and it can be submerged for limited periods of time. Always operate the device in accordance with the water rating listed in the device specifications (Garmin PowerSwitch Specifications, page 5). Submerging the device in water for prolonged periods of time may cause corrosion on the electrical contacts.

Device Information

Garmin PowerSwitch Specifications

Dimensions (D x W x H)| 75 x 125 x 32 mm (2.95 x 4.92 x

1.26 in.)

---|---
Operating temperature range| From -25° to 85°C (from -13° to 185°F)
Wireless frequency| 2.4 GHz @ 10 dBm
Power input| From 12 to 16 V using the included vehicle power cable.
Maximum accessory output| 30 A
Maximum system output| 100 A
Current draw with all outputs off| 3 mA
Water rating| IEC 60529 IPX71

References

• Garmin Customer Support
• Garmin International | Home
• Water Rating Definitions | Garmin

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>