migoal H1 Wireless Headphone User Manual
- June 5, 2024
- migoal
Table of Contents
migoal H1 Wireless Headphone
READ CAREFULLY AND KEEP THIS MANUAL
Caution
To ensure safe and proper use, read all safety information before using the
device. Only use with manufacturer-approved batteries, chargers, accessories,
and supplies. THIS DEVICE IS NOT A TOY, do NOT allow children or pets to use
or play with this device
- Do not disassemble, modify, or repair the device.
- Do not expose to extreme temperatures (heat or cold), open flames, humid, or wet conditions.
- Do not Submerge in water.
- Low power may cause poor Bluetooth connection or sound distortion.
- Do not overcharge battery.
- If using with a USB adapter, make sure the adapter is not damaged.
- Do not allow the USB port or the connectors of the supplied USB cable to be exposed to dust or water, or to come into contact with any conductive materials such as liquids, metallic powders, etc.
- The headphones contain a built-in battery and should not be disposed of with regular household waste. Please consult the local authorities on the correct way to dispose of this device.
In the Box
- Wireless Headphones (x1)
- Micro-USB Charging Cable (x1)
- 3.5 mm AUX Cable (x1)
- User Manual (x1)
Location of Controls
Getting Started
Charging the Headphones
Plug the small connector of the supplied USB charging cable into the charging
port on the headphones. Plug the large connector into a USB power source, such
as the USB port on a computer, or a 5V USB wall adapter (not included). The
LED indicator will light up RED when charging, and turn OFF vwhen fully
charged When the headphones are low on power, a tone will be heard indicating
that they need to be recharged.
Powering ONOFF
- Press + hold the Power button for 3 seconds to power ON. A tone will be heard, and the headphones will enter Bluetooth pairing mode. They will automatically re-pair to any nearby, previously-paired device with Bluetooth enabled.
- Press + hold the Power button for 4 seconds to power OFF
Bluetooth Pairing
- Power the headphones ON. A tone will be heard, the LED indicator will flash RED and BLUE, and the headphones will enter Bluetooth pairing mode.
- Set your mobile device to search for Bluetooth devices. When it appears, select BT Name from the list of found devices.
- After a successful pairing, a tone will be heard, the LED indicator will slowly blink BLUE, and you will be able to play music on the headphones.
In Bluetooth mode, volume and playback can be controlled with the following:
- Press the Power button to pause and resume playback.
- All volume & playback can be controlled by the paired device.
Phone Calls
When connected to a phone via Bluetooth, you can control phone functions with
the controls on the headphones.
- Press the Power button to answer an incoming call. Press again to end the call.
- Press+ hold the Power button for 2 seconds to reject an incoming call.
- 2x Press the Power button to redial the last outgoing number.
Using the 3.5 mm AUX Cable
- Plug one end of the included 3.5 mm auxiliary cable into the 3.5 mm auxiliary input port on the headphones.
- Plug the other end into the headphone jack or 3.5 mm aux output port on your media-playing device. Switch input modes until you reach AUX mode.
- In AUX mode, all playback and volume adjustment will be controlled by your connected device.
Note : The headphones do not need to be charged or powered on to listen using the AUX cable.
FCC Information
This device complies with Part 15 of the FCC Rules.
Caution: Any changes or modifications not expressly approved could void
the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pur Suant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interterence in a residential installation. This equipment generates, uses and
can radiate radio trequency energy and, it not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
oCCur in a particular installation. f this equipment does cause harmful
interference to radio or television réception, which can be determined by
turning the equipment oft and on, the user iS encouraged to try to correct the
interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Information
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure conditions without restriction
WARNING Li-ion Battery Inside
This product is fitted with a LiHon battery. Do nat damage, open, or dismantle
the battery and do not use it in damp and/or corrosive conditions. Use only
with compatible chargers. Never dispose of batteries in a fire, and never
expose them to high temperatures. Do not expose the product to temperatures
exceeding 60°C (140H.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>