Miele XKM 3200 WL LMD Communication Module Instructions

Miele XKM 3200 WL LMD Communication Module Instructions

Notes about these instructions

Important warnings

Information which is important for safety is highlighted in a thick framed box with a warning symbol. This alerts you to the potential danger of injury to people or damage to property.
Read these warning notes carefully and observe the procedural instructions and codes of practice they describe.

Notes

Information of particular importance that must be observed is highlighted in a thick framed box.

Additional information and comments

Additional information and comments are contained in a simple frame.

Operating steps

Operating steps are indicated by a black square bullet point.

Example:

• Select an option using the arrow buttons and save your choice with OK

Display
Certain functions are shown in display messages using the same font as that used for the function itself in the display.

Example:
Settings menu.

Queries and technical problems
In the event of queries or technical problems, please contact Miele.
Contact details can be found at the end of the operating instructions for your cleaning machine or at www.miele.com/professional.

Definition of terms

Cleaning machine
In these operating instructions, the washer-disinfector is referred to as “the cleaning machine”.

Module
The communication module is generally referred to as the module in these operating instructions

Intended use

The XKM 3200 WL LMD communication module supplied enables an interface to be set up between a Miele washer-disinfector and a terminal device or local network. The data connection is a standard Ethernet or WiFi connection. The interface serves a number of purposes, including process documentation. Further information on process documentation can be obtained from Miele.

Only terminal devices (PCs, tablets, printers, etc.) compliant with
EN/IEC 62368 should be used.
Only specialists are permitted to configure the interface.

The communication module can be used in the following washer-disinfectors:

• PG 8562
• PG 8581
• PG 8582
• PG 8582 CD
• PG 8583
• PG 8583 CD
• PG 8591
• PG 8592
• PG 8593

Items supplied

Scope of delivery

• XKM 3200 WL LMD communication module

Technical data

Voltage, rated load, fuse rating| ****

See data plate

---|---
Connection cable| Approx. 1.5 m
Ethernet baud rate| 10/100 Mbit/s
WiFi standard| 802.11 b/g/n
WiFi frequency band| 2400-2483.5 MHz
Maximum WiFi transmission power| < 100 mW
Temperature during operation| Up to max. 80 °C
 marking| 2014/53/EU Radio Equipment Directive

EU Conformity declaration

Miele hereby declares that the XKM 3200 WL LMD communication module complies with Directive 2014/53/EU.

The complete text of the EU declaration of conformity can be downloaded from the following website by quoting the product name or serial number:

• www.miele.com/professional

  • Products > Download
    or

  • Service & Support > Operating instructions

Guide to the appliance

Appliance overview

1. Reset/WPS button

2. LED indicator
   Indicates operational readiness after installation and active communication when in operation.

3. Data plate (located on the side)

4. Data cable

Switching on and off

The module does not have a separate On/Off switch. It is switched on and off together with the cleaning machine.

The module requires approx. 90 s for initialisation after switch-on.
Until this has happened data cannot be transferred and interface settings cannot be changed.

LED indicator

The LED indicator (light emitting diode) provides status information about the communication module

ready for operation.
Lit up YELLOW| Network is configured but there is no connec- tion to the network.
Lit up RED| The module is not configured.
Off| Power is not being supplied to the module. Check that the module is in the correct position in the module slot.

Button

The button on the module has several functions.

WPS button
The WPS button can be used to establish a WiFi connection between the module and your router or repeater (WPS, WiFi, Protected Setup).
WPS-enabled routers or repeaters must be used.

Reset button
The button on the module can be used to reset the module to the factory default settings.

• Press the button for approx. 5–9 seconds to restore the factory default settings.

Data protection and data security

When you activate the networking function and connect your appliance to the Internet, your appliance sends the following data to the Miele Cloud:

• Appliance serial number
• Appliance model and technical features
• Appliance status
• Information about the software status of your appliance

Initially, this data cannot be assigned to a specific user and is not saved permanently. Data cannot be saved permanently or assigned to a specific user until after you have linked your appliance to a user.
Data transmission and processing are governed by Miele’s strict security standards.

Factory default settings for network configuration

You can reset all of the settings on the communication module or your integrated WiFi module to the factory default settings. The network configuration should be reset whenever an appliance is being disposed of or sold, or if a used appliance is being put into operation.
This is the only way to ensure that all personal data has been removed and the previous owner will no longer be able to access the appliance.

Copyrights and licences

For the purpose of operating and controlling the communication module, Miele uses proprietary or third-party software that is not covered by open source licensing terms. These items of software/software components are protected by copyright. The copyright powers of Miele and third parties must be respected.

Furthermore, this communication module contains software components which are distributed under open source licence conditions. The open source components contained in the appliance along with the corresponding copyright notices, copies of the licensing terms valid at the time and any further information can be accessed locally by IP using a web browser (https:///Licenses). The liability and warranty arrangements for the open source licences displayed at this location only apply in relation to the respective rights holders.

Warning and Safety instructions

To avoid the risk of accidents and damage to this communication module please read these instructions carefully before using it for the first time.
Keep these instructions in a safe place.

Please also read the operating instructions for your washerdisinfector and pay particular attention to the Warning and Safety instructions.

• This communication module must only be used for applications specified in the operating instructions. Changes or modifications to it and incorrect use of it are not permitted as this can be dangerous.

• The communication module must only be installed, commissioned and serviced by Miele service or by a suitably qualified person.
  Repairs are only to be undertaken by Miele Service. Repair work by unqualified persons could be dangerous.

• Check the communication module carefully before installation for any visible damage. A damaged module could be dangerous and must not be installed.

• Before installing the communication module compare the connection data (voltage and frequency) on the data plate with that on the data plate of your washer-disinfector. If the data does not match, the module could sustain damage. If in any doubt, consult an electrician.

• The communication module housing must not be opened on any account.
  Touching live electrical components or altering the electrical or mechanical components is dangerous and could cause the module to malfunction.

• Make sure that the data cable for the communication module is assembled and routed correctly. The cable must not be kinked or trapped, for example. It must not be routed around sharp edges or be placed under tension.

• The WiFi technology supported by the module can be temporarily or completely disrupted e.g. by structural conditions or the set-up location. For this reason availability of featured functions cannot always be guaranteed.

Fitting and installation

Getting ready to use WiFi

If you wish to use the WiFi connection on the module, please note the following prior to installation.

Range and availability of WiFi signal
The WiFi range or signal strength is dependent on the structural environment. Reinforced concrete walls and ceilings, metal surfaces, metal-vaporised films, glass screens and fire protection constructions can muffle or divert the signal, therefore reducing the range.

If the cleaning machine is located under a metal worktop or is surrounded by metal cabinets, for example, the signal will be almost completely blocked.

LAN cable
Do not connect the LAN cable to the network. Plugging in the LAN cable switches off the WiFi signal automatically. The technology does not support the simultaneous use of WiFi and LAN.

WiFi password

• Take a note of the serial number of your cleaning machine. This is required as the password for establishing the WiFi connection. You will find the serial number on the data plate on the cleaning machine. The position of the data plate is indicated in the machine description for the cleaning machine.
  Example:
  
  The serial number of the module, without the initial zeroes, acts as
  the password. Example:
   01 / 0001234567890
  Password: 1234567890

Installation

Before fitting the communication module compare the connection data (voltage and frequency) on the data plate with that on the data plate of your cleaning machine. If the data does not match, the module could sustain damage. If in any doubt, consult a qualified electrician.

• Disconnect the cleaning machine from the mains electricity supply

Module slot
The module is inserted into the module slot on the cleaning machine.
The module slot is located on the back of the cleaning machine.

• If the cleaning machine is installed in a niche:

  • Pull the cleaning machine forwards out of the niche.

•  If the cleaning machine is installed under a worktop:

  • Open the door.
    

• Unscrew the fixing screws.

• Pull the cleaning machine out from under the worktop. Take care not to damage the hoses and cables when moving the machine.

Inserting the module

• Remove any stickers or protective caps as necessary from the slot aperture.
  

• Push the module into the module slot. Gently push the module until it clicks into place.

Laying data cables
The technology does not support the simultaneous use of WiFi and LAN.

WiFi
If you wish to use the WiFi connection, the LAN cable must not be connected to a network or terminal device. The WiFi signal will only be available if the LAN cable is not plugged in.

• We recommend that you roll the LAN cable up and secure it somewhere at the back of the machine. This will stop it from getting in the way when the cleaning machine is being installed or undergoing maintenance work.

LAN
If you wish to use the LAN cable for data transfer instead of the WiFi connection, connect the LAN cable to your terminal device. Plugging in the LAN cable switches off the WiFi signal automatically.

• Take care to ensure that the cable is laid correctly; it should not be kinked or trapped, for example. Keep the cable away from sharp edges and do not place it under tension.

Only terminal devices (PCs, printers, etc.) which comply with EN/IEC 62368 should be used.

Switching the cleaning machine on

• Connect the cleaning machine to the electricity supply.
  The module is supplied with mains voltage by the cleaning machine. No additional power connection is required.

After around 90 s, the module is ready for operation and the interface can be configured.

Network connection

Establishing the WiFi connection

LAN cable
Do not connect the LAN cable to the network. Plugging in the LAN cable switches off the WiFi signal automatically. The technology does not support the simultaneous use of WiFi and LAN.

WPS login

WPS login requires the use of a WPS-enabled WiFi router or repeater

• Switch the cleaning machine on.
  After around 90 s, the module is ready for operation.

• Briefly press the button on the module (1–4 seconds).
  Never press the button for more than 4 seconds, as this will reset the module to the factory default settings; see Reset button.

• Activate the WPS function on your WiFi router or repeater within 2 minutes.

The LED on the module will light up green if the WPS login is successful.

WiFi access point
If you do not wish to set up a WPS connection and the module has not yet been configured for a WiFi network, a WiFi access point will open automatically when the cleaning machine is switched on. You can connect the access point to your PC.

• To do this, switch the cleaning machine on.
  After around 90 s, the module is ready for operation.

• Configure the interface of your cleaning machine. To do this, follow the instructions in the “Configuring the interface” chapter.

• Open the module’s web interface and configure the interface under “WiFi Settings”; see “Configuring the interface”.

Configuring the interface

Under no circumstances must the internet be accessed via the washer- disinfector, e.g. via port forwarding!
Make sure that your Internet connection or your router is configured accordingly.

Only specialists are permitted to configure the interface.

Opening the menu

• Switch the cleaning machine on using the  button.
  You must wait approx. 90 seconds before starting to configure the interface.

• Open the menu as follows:
  button

  • Further settings
  • Interface
    

• Select the Ethernet interface and confirm your choice with OK.
  The following options are available:

  • – Module status
    Displays the connection status.

  • – DHCP
    The Ethernet interface can either be implemented via a Dynamic
    Host Configuration Protocol (DHCP) or by setting the individual parameters.

Checking the connection status

• Select the Module status option and confirm your choice with OK.
  
  The following messages may appear in the display:

  • Active
    The module is ready for operation.

  • Initialising, module not yet active
    The module has not finished initialising. This process takes approx.
    90 s.

  • Inactive
    No module has been detected.
    Check the installation of the module. Switch the cleaning machine off and then back on again.
    If the message continues to appear, contact the Miele Customer Service Department.

Selecting settings
Document all settings in case technical support is required at a later date.
DHCP must be deactivated prior to manual intervention.

• Select the DHCP option and confirm your choice with OK.
  

• Select the Off option and confirm your choice with OK.
  The following settings are then available for selection:

  • IP address
  • Subnet mask
  • Standard gateway
  • DNS server automatic
  • DNS server 1
  • DNS server 2
  • Port type (not relevant)
  • Port (not relevant)

• Select an option and confirm your choice with OK. You can then make the following settings according to the information displayed on the screen.

To enter the IP address, Subnet mask etc., the display contains the following information:

The current setting is shown on the middle line of the display. It can be changed using the options shown in the bottom line. The top line shows which option has been selected from the bottom line. The following data entry options are available:

• Numbers from 0 to 9.
• Decimal point “.”.
• Use the symbol to delete the last position.
• Select the OK symbol on the display to save the setting. The display will then revert to the main menu.
• Select the symbol on the display or use the button to exit the process without saving the setting(s) made. The display reverts to the main menu.

The IP address, Subnet mask, etc. must always be entered in full. If the IP address is 192.168.1.23, for example, enter 192.168.001.023.

• Use the arrow buttons (right) and (left) to move the cursor to
  the option you require.

• Confirm each entry with OK.

• To save your entries, select the OK symbol on the display and confirm with the OK button.

Activating the configuration

The interface configuration is only effective after the cleaning machine has been restarted.

• Wait approx. 10 seconds before switching the cleaning machine off for a restart.
• Switch the cleaning machine off and then back on again with the button.
• Wait approx. 90 seconds for the module to initialise.
• Then check if the interface is working.

Fault 559

If the fault message Fault 559 is displayed during commissioning or a programme is interrupted with this message, the RS232 interface is activated and must be deactivated.

• Open the menu for configuring the RS232 interface via Further settings / Interface.
• Select the Ethernet option and confirm your choice with OK.

The RS232 interface is deactivated. After around 90 s, the module is ready for operation.

Web interface

The XKM 3200 WL LMD module has a dedicated web interface via which the network settings can be configured, printers can be set up or the password can be changed.

The interface can be accessed from any workstation on your local network. A configured interface in the controller of the cleaning machine, an up-to-date web browser and an existing network connection to the cleaning machine are required.

The web interface is divided into 2 web pages. The output language is English.

• Enter one of the following addresses in the address bar of your browser (where corresponds to the IP address of your cleaning machine).

Password

https:///password.html

When the web interface is opened for the first time, the “Admin” user must set up a password for their profile (once only). A module reset will reset the module settings to the factory default settings; this will include resetting the password for the “Admin” user.

• Change Password

Changing the module password

The password must always be reset at the factory as a first step before further settings can be made. When setting the password for the first time, the field for the old password must be left blank.

Configuring the module
https:///index.html

To change the settings, you must enter a user name and a password.
You cannot access the settings without doing this.

• WiFi Settings
  Selecting a WiFi network

• IP Configuration
  Modifying the interface configuration

• Network Printer
  Specifying a network printer for printing reports

• Reset
  Restart the module or restore the factory default settings (this will also delete user profiles and module passwords)

Caring for the environment

Disposal of the packing material

The packaging is designed to protect against transportation damage.
The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled.

Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites.

Disposing of your old appliance

Electrical and electronic appliances contain many valuable materials.
They also contain certain materials, compounds and components which were essential for their correct functioning and safety. These could be hazardous to human health and to the environment if disposed of with household waste or if handled incorrectly. Please do not, therefore, dispose of your old appliance with household waste.

Instead, please make use of officially designated collection and disposal points to dispose of and recycle electrical and electronic appliances in your local community, with your dealer or with Miele, free of charge. By law, you are solely responsible for deleting any personal data from the old appliance prior to disposal. You are legally obliged to remove any old batteries which are not securely enclosed by the appliance and to remove any lamps without destroying them, where this is possible. These must be taken to a suitable collection point where they can be handed in free of charge. Please ensure that your old appliance poses no risk to children while being stored for disposal.

Manufacturer:
Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
Germany

Manufacturing site:
Miele & Cie. KG
Mielestraße 2
33611 Bielefeld
Germany
Internet: www.miele.com/professiona

References

• Professional
• Miele Professional DE | Entdecken Sie unsere gewerblichen Lösungen.
• Miele Professional | Soluzioni per il Lavaggio Professionale
• Velkommen til Miele – Immer Besser
• Miele Professional NO | Se våre profesjonelle løsninger
• Miele Professional PT | Descubra as nossas soluções industriais
• Miele Professional SE |Upptäck våra kommersiella lösningar
• Miele Professional - Bem-vindo ao nosso website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>