DS18 Jvoce Jeep Or ATV Roll Cage Pod With Dual 6.5 Inch Hybrid Mid-Range Driver Horn Loudspeakers Owner’s Manual

OWNER’S MANUAL

JEEP OR ATV ROLL CAGE POD WITH DUAL 6.5″ HYBRID MID-RANGE / DRIVER HORN LOUDSPEAKERS

GENERAL SPECIFICATIONS

Nominal Diameter . . . . . . . . . Dual 6.5” / 165mm
Nominal Impedance . . . . . . . . . 4+4 ohm
RMS Power handling . . . . . . . . . 2 x 225W
MAX Power Handling . . . . . . . . . 2 x 450W
Sensitivity (1w/1m . . . . . . . . . . . . 98dB
Frequency Response . . . . . . . . . . . 80Hz-20KHz
Recommended Hi Pass Crossover . . . . . . . . 100Hz

BODY / FEATURES

Enclosure Material . . . . . . . High Density Plastic Molded with Color Injected
Marine Grade Type . . . . . . . . IP65 + UV Stable
RGB LED Lighting: . . . . . . . . Yes, Around the Grill
Single or Pair . . . . . . . . . . Single
Grill. . . . . . . . . . . . . . Plastic ABS injected
Clamps. . . . . . . . . . . . . . . . . . . . 1 x Die-Cast Flat Bracket for Jeep JL Roll Cage or Universal Fit 1 x Tube Clamp Adjustable (2″~3″) 360 Degree Rotation Mounting, Buried Wire or Open Wire Mounting Optional, Included NBR Pad And Stainless Hardware (Screws, Stop Washers, Hexagon wrench, Safety Rope, Threadlocker Glue)

Front Logo . . . . . . . . . . . . . . . Yes
Finish . . . . . . . . . . . . . . . . . Matte Black
Input Wire. . . . . . . . . . . . . . . . Speaker x 2 (Stereo Configuration) + RGB Lights

WOOFER SPECIFICATIONS

Voice Coil Diameter. . . . . . . . . . 1.5″ / 38.6mm
Cone Material. . . . . . . . . . . . . Waterproof Paper
Surround Material. . . . . . . . . . . . . . . Cloth
Basket Material . . . . . . . . . . . . . Aluminum
Magnet Material . . . . . . . . . . . . . Ferrite
Magnet Weight . . . . . . . . . . . . . . 27 Oz

DRIVER SPECIFICATIONS

Voice Coil Diameter. . . . . . . . . . . 1″ / 25.4mm
Type . . . . . . . . . . . . . . . . . . High Compression Horn
Diaphragm Material . . . . . . . . . . . Titanium
Magnet Material . . . . . . . . . . . . . Neodymium
Crossover . . . . . . . . . . . . . . . . 6 dB/Oct Filter
Horn Diameter. . . . . . . . . . . . . . . 3″ / 76.2mm

THIELE & SMALL PARAMETERS

Equivalent Volume . . . . . . . . Vas . . . 2.2L
Excursion (one way) . . . . . . . Xmax . . 9.2mm
Free Air Resonance. . . . . . . . Fs . . . . . 199Hz
Total Factor. . . . . . . . . . . . . . Qts . . . . 1.214

MEASUREMENTS

Overall Width. . . . . . . . . . . . . . . 16.22″ / 412mm
Overall Depth. . . . . . . . . . . . . . . 5.87″ / 149mm
Overall Height (without Clamp) . . . . . . 8.35″ / 212mm

MEASUREMENTS

READ BEFORE INSTALLATION

1. Be sure to carefully read and understand the instructions before attempting to install these speakers.
2. For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
3. For easier assembly, we suggest you have all your tools in hand- Drill, Allen set, Crimp, Soldering iron, Wire Strippers, Heat-shrink, etc.
4. Use high quality “Waterproof’ connectors for a reliable installation and to minimize signal or power loss.
5. Think before you drill! Be careful not to cut or drill into gas tank, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.
6. Never run wires near fuel lines or power (if possible). Running the wires inside the hull or car area provides the best protection.
7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the tower.
8. Make sure that the mounting clamp is tight before leaving the dock.
9. Decide early what type of LED lighting you want (if any) and wire accordingly (NOTE :if you want “Dancing Light” look to the WiFi or RF or BT remote controlled LED light box. The easy way to have lighting … YOUR way!)

INSTALLATION EQUIPMENT

• An Electric Drill With Bits
  Un taladro eléctrico con bocas

• Allen / Hex Key / Wrench Set
  Allen / Llave hexagonal / Juego de llaves

• Philips Head And Standard Screw Drivers
  Destornilladores estándar Phillips

• Wire Strippers
  Pelacables

PACKAGING INCLUDES

1 x Jvoce Enclosure with dual PRO-HY6.4B Hybrid Loudspeaker
1 x Flat Bracket for Jeep JL roll cage
1 x Tube clamp adjustable 2″ to 3″ diameter
1 x 6mm Hex wrench chromed
1 x 5mm Hex wrench chromed
1 x 4mm Hex wrench chromed
1 x NBR pad
1 x safety Rope
1 x Thread locker glue
1 set of screws and stop washers

NOTE: The stainless steel hardware supplied with your speakers has been chosen to resist rust and corrosion. If the particular hardware supplied will not work for your installation purposes, please be sure to use only appropriate marine grade (stainless steel) mounting hardware.

INSTALLATION & CONNECTION OPTIONS

If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

Blue LED (-)
Red LED (-)
Green LED (-)
Black 12V DC (+)
White Left Speaker (+)
White/Black Left Speaker (-)
Yellow Right Speaker (+)
Yellow/Black Right Speaker (-)

To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:

• Black wire”BK” connected to battery Positive (+) 12V
• White Color Light “R”; “B” and “G” connected to battery Negative (-)
• Green Color Light “G” connected to battery Negative (-)
• Red Color Light “R” connected to battery Negative (-)
• Blue Color Light “B” connected to battery Negative (-)
• Purple Color Light “R” and “B” connected to battery Negative (-)
• Yellow Color Light”R” and “G” connected to battery Negative (-)
• Cyan Color Light “B” and “G” connected to battery Negative (-)

Blue LED (-)
Red LED (-)
Green LED (-)
Black 12V DC (+)
White Left Speaker (+)
White/Black Left Speaker (-)
Yellow Right Speaker (+)
Yellow/Black Right Speaker (-)

INSTALLATION BEGINNING MOUNTING

Step 1: Remove tower speakers from the packaging and ALL hardware.
Step 2: Find a GOOD location that allows for easy wiring of the speaker (and LED lights) -PLUS does NOT impair your movement around the location.
Step 3: Using the supplied 6mm hex wrench spin out the 4-M8 screw that holds the top clamp
Step 4: Drill 015 – 020 mm hole on mounting tube bottom align the clamp wire out hole.
Step 5: Connect the speaker wire AMP out and LED controller, Insulated lock the clamp to the tube.
Step 6: Cut the length of the rubber pad and wires outlet according to the diameter of the installation pipe.

Step 7:Wrap the rubber pad around the pipe and align wire out hole According to the diagram.

Step 8: Push the wire into the tube, press on the rubber pad, and lock the top clamp.
Step 9: Take down the safety rope and hang it on the pipe, lock the screw gasket safety rope lifting ring on the clamp base, and apply screw fastening glue on the screw before locking.
Step 10: If need be, rotate the speakers for best dispersion, this easily done by locating the 6mm & 4mm hex wrench set screw on the side of the clamp base, rotate the speaker/enclosure to the desired angle, once there… locking the screws tight. Avoid vibration, clamp loose!!!

Step 11: During the mounting process, you should have located the spot to drill your tower bar for the 6 conductor wire (Speaker and RGB lightning wiring) insertion. Or NOT (see Tie-wrap solution below)

Step 12: When you want to install a flat mounting, remove the clamp and take out the 6 core through it into the flat mounting bracket, then assemble it, see depiction below.

FOR MORE INFORMATION
PLEASE VISIT
DS18.COM

References

• Official DS18 Pro Audio Store - Speakers, Subwoofers, Amps & More!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>