havit W320 Wireless Charging with Alarm Clock and Ambient Light Instruction Manual
- June 5, 2024
- havit
Table of Contents
havit W320 Wireless Charging with Alarm Clock and Ambient Light
Packing list
*Wireless
charger 1**
|
*USB to Type-C cable 1**
---|---
*Warranty
card1**
|
*User’s
manual1**
(the above picture is for reference only.specific to prevail in kind)
Function Buttons
Functions
Power Connection
- Plug the USB-A end of cable into the power adapter while plug Type-C end into the product.
- The product will be ready and stand by after all indicators are on.
Wireless Charging
- Output: 15W
- lndicator Display: Power connection successful – blue light flashes once
Standby – light off
Charging – blue light on
Charged – light off
FOD – blue light flashes continuously
Alarm Clock Functions
-
Founction Buttons: Light, Alarm, +, -.
-
Time System Setting :
Double press Alarm button to setup 12-hour time system and 24-hour time system. AM and PM will display while 12-hour time system is set. -
Time Setting:
- Press Alarm button once to enter minute setting, adjust value with +/-;
- Press Alarm button once after minute setting, to enter hour setting, adjust value with +/-;
- Press Alarm button a third time to finish time setting.
- Alarm Setting:
- Press”+” 3 seconds to activate or deactivate Alarm 1; Press”-” 3 seconds to activate or deactivate Alarm 2. Alarm indicator is on while Alarm is activated;
- While activated, press Alarm button 3 seconds to enter alarm minute setting, adjust value with +/-;
- Press Alarm button once after alarm minute setting, to enter alarm hour setting, adjust value with+/-;
- Press Alarm button a third time to finish alarm time setting.
- Stop alarm: If Alarm 1 bell rings 3 minutes before automatic switch-off
while no any operation; or press”+” 3 seconds to stop the ring, Alarm 1 keep
indicator on display, tomorrow Alarm 1 will work in same time. Same operation
as Alarm 2. 6)Sleepy mode:
Press any button to enter Sleepy Mode when bell rings of Alarm 1 or 2. The indicator flashes, Bell will rings for 3 more times after 5 minutes.
Note: Alarm button is out of function under the Sleepy Mode, rest buttons
keep function to set.
If time setting is needed, please press “+” 3 seconds to stop alarm 1 or press
“-” 3 seconds to stop alarm.
2. All buttons will function normally.
Time display brightness: 4 grades (Min/Med/Mid/Max/Off)
- Set the brightness by pressing “+” or”-” button .
- To increase display brightness: Press”+” button.
- To decrease display brightness: Press”-” button.
Notice: By default, the clock keep the max brightness when power is connected.
Night Light Setting
-
Night light can be set into 9 color modes:
White, RGB shade, Red, Orange, Yellow, Green, Light blue, Blue and Purple. -
Press the Light button to turn on the night light with White color.
-
Press again the Light button turn to RGB shade, it is in turn of Red-Orange-Yellow-Green-Light Blue-Blue-Pink.
-
Press again the Light button turn to single color mode, Press one more time the Light button, fix the color. The last press will turn off Night light.
Notice: By default, White color in standard brightness.
F.Eco-power function:
- Button cell inside is only for time memory.
- All functions are out during power disconnection. Functions restored when power is connected.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part li5 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio ortelevision
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
To maintain compliance with FCC’ s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
NOTICE
- Attention: In order to function alarm, wireless charging, night light and USB output work at same time, power shall be connected by a QC3.0 adapters or PD adapters. If connected by a 5V2A adapter, only wireless charging and alarm can work.
- Do not squeeze or collide.
- Do not disassemble or put into the fire, water, to avoid short-circuit leakage.
- Do not use wireless chargers in severe high temperature, humidity or corrosive environments to avoid leakage of damaged circuits.
- Do not place too close to magnetic cards (ID cards, bank cards, etc.) with magnetic strips or chips to avoid magnetic card failure.
- Keep more than 20cm between the implanted medical device (pacemaker, implantable cochlea, etc.) and the wireless charger to avoid potential disruption to medical devices.
- Keep children from the product in case they play the wireless charger as a toy to avoid accidents.
- Keep the wireless charg1er and receiver device away from water and other liquids.
- To clean the charger, make sure the power supply is disconnected.
- Usage temperature: 0-45 ·c.
- Usage humidity: 20-85% (40 ·c )
- Pictures in this manual are all illustration. Final product is subject to fact.
- Inside package: alarm charger, charging cable, manual.
- Power adapter is not included. Please purchase or use phone original adapter.
Product parameters
Model: W320
Material: ABS
Input: 5V=2A,9V=2.5A, 12V=2A
Output: 15W (compatible with 10W/7.5W/5W)
USB output: SV = 1 A( max)
Charging efficiency: 73%
Charging distance: <8mm
Frequency: 110-205KHz
Size: 10.510.510cm
Weight: 21 0g+0.5g
Warning
- Please don’t throw the product violently.
- Please don’t disassemble the product yourself
- Please don’t place this product near heat sources
- Please don’t place the product close to water or in damp places.
[ **www.havit.hk**](http://www.havit.hk)
Documents / Resources
|
havit W320 Wireless Charging with Alarm Clock and Ambient
Light
[pdf] Instruction Manual
W320, 2AI6I-W320, 2AI6IW320, W320 Wireless Charging with Alarm Clock and
Ambient Light, Wireless Charging with Alarm Clock and Ambient Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>