Dongguan Zhuoshi Intelligent Tech M23A Motorcycle Phone Mount with Qi Wireless Charger User Manual
- June 5, 2024
- Dongguan Zhuoshi Intelligent Tech
Table of Contents
Dongguan Zhuoshi Intelligent Tech M23A Motorcycle Phone Mount with Qi
Wireless Charger User Manual
Statement:
Thank you very much for choosing this product! Before using this product,
please read the instruction manual carefully. All information in this manual
may be changed without notice. The company reserves the right to change the
information at any time without prior notice.
Introduction
-
This motorcycle phone mount with wireless charger, compatible with Qi 15W/ IOW/7.5W/5W wireless charging modes on the market. Input; DC 12V-24V
-
There is an LED aperture and a power switch in the center of the phone mount, When phone is not charged, the LED aperture power can be controlled by power switch, When charging phone, the LED aperture power turns off automatically.
-
One-push quick lock and release: Tilt the phone to push the top, and the phone holder will automatically hold your phone firmly. Hold the phone to push the top again to release it and take out your phone. Everything done with one hand.
-
There is a safety switch on the back of the mount, after placing the phone, please tighten the knob; before taking out the phone, please loosen the knob,
-
The main body of the phone mount is made of 6061-T6 aluminum alloy material, CNC production process, firm structure and smooth surface,
-
The phone holder panel and five-claws are covered With soft silicone, Shockproof
protection, and prevent the phone from being scratched. -
When the product is received, the five claws have been covered with red soft silicone,
The package comes with 5 pieces of black soft silicone, you can replace the silicone
on the five claws according to your preference. -
When receive product, the vibration dampener is already installed on back of phone
holder. Attach the phone holder to the handlebar rail or rear-view mirror fram via the
included anti-theft ball socket arm and handlebar/rear-view mirror mounting base, -
The anti-theft double socket arm is made of 6061-T6 aluminum alloy material. The anti-theft knob and anti-theft key Of the socket arm are made of PA66+GF30% material.
-
Adjustable screws are installed on the bottom, top and back of the holder to adjust the Width, height and thickness of the phone holder. The maximum thickness Of compatible mobile phones is up to 20mm. Can accommodate 4.7-72 inch mobile phones.
-
Waterproof grade: IP66
If you have any questions about the quality and use of the product you have received, please feel free to contact us. Our after-sales team will give you the fastest reply within 24 hours!
Package Contents
Installation Steps
Mount to handlebar
Mount To Rear-View Mirror Frame
Adjust Length & Width
Loosen the corresponding screws on the back Of the holder, and adjust the
length and width to the position that best matches your phone.
Adjust Thickness
Loosen the corresponding screws at the bottom and top of the holder, and
adjust the thickness to the position that best matches your phone
Two Ways To Connect Power
One-Push Automatically Lock
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled
environment. This transmitter must not be co‐located or operating in
conjunction with any other
antenna or transmitter. During the operation of device a distance of 15 cm
surrounding the
device and 20 cm above the top surface of the device must be respected.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>