KOOBE K-Box AirCube Air Monitor Instructions
- June 5, 2024
- KOOBE
Table of Contents
KOOBE K-Box AirCube Air Monitor
FCC STATEMENT
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: this device may not cause harmful interference,
and this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
Button operation of “Xiaomei” intelligent control
box
On key: in standby mode, the panel standby LED I ight is on (brightness is
50%), except for on key, other keys do not work; when you press on key once,
the machine will enteron state, the panel
power on LED I ight is on (brightness is 100%), the panel wind speed LED light
is on;on default:wind speed l ,no timing, LCD display: PM2.5, and then trigger
the switch Key to returnthe machine to
Wind speed key: in the power on state, short press the wind speed key, the
panel wind speed LED light is on, the intelligent LEDlight is off, the buzzer
rings, the wind speed gear changes by pressing “1-2-3” cycle, in the
intelligent mode, press thewind speed key to exit the intelligent mode, and
the wind speed is in the next gear of the wind speed in the intelligent mode.
Timing key: when the timing key is pressed in the power on state, the timing
LED light will be on, then the buzzer will ring once, and the timingshutdown
time will be set: it can cycle between lh-4h-8h; when the timing value is
selected, the countdown will be started, and the timedisplaywill be reduced by
one hour after each hour, and the ti me wil I return to the stand by state as
soon as the ti me arrives.
Wi Fi Key: After power on, long press Wi Fi key for 3 seconds, Wi Fi I ight flickers to a utomatica I ly connect to the network. During the connection process, if WiFi light is on for a long time, it means the connection is successful. If WiFi light flickersall the time, it means the connection fails. When there is a key operation, the data is sent in real time. When there is no key operation, the data is sent every 30s, including PM2.5 data, gear, timing and location (city).
Smart key: in the power on state, press the smart key briefly, the machinewill enter the smart mode, and the wind speed wil I run accord ing to the air qua I ity state.In the i ntel I igent mode,if you press the wind speed key,the machine will exit the intelligent mode Mode, the next gear of wind speed in intelligent mode.When the air quali ty changes from excellent to poor, the fan needs to change to the corresponding gear immediately. When theairquali ty changes from poor toexcellent, the fan shall maintain the original gear for 30s and then change to the corresponding gear.
| PM2.5 | Air q uali ty | Wi ndspeed |
|---|---|---|
| <75UG | Excellent air q uali ty | 1 stall s |
| 75UG PM2.5<150UG | Light pollution | 2 stall s |
| PM2.5 l S0UG | Heavypoll ution | 3 stall s |
1 smart box + multiple module fans that can be stacked at will, each module fan can work independently. When multiple module ans are combined into one machine (up to 6 fans are combined together), the control box will give instructions, and the module fan will execute the work instructions uniform ly. If any of the modules areda magedthe normal use of the whole machine wi 11 not be affected If there is any damage, only the damaged module fan needsto be repaired separately, which can be easily solved after-sales.