HiKOKI ET 36A Multi Volt Adapter Instructions

HiKOKI ET 36A Multi Volt Adapter

AC/DC ADAPTER SAFETY WARNINGS

1. Please only use the professional power tools specifi ed in this manual and in HiKOKI catalogs. Failure to do so may result in accident, injury or malfunction.

2. Do not place the box upside down.
   Prior to use, place the box LED side up.

3. Please use the product properly.

4. Always use the charger at the voltage specifi ed on the nameplate. Do not use with boosters or other types of transformers.
   Doing so could result in overheating or fi re.

5. Do not use the adapter at temperatures less than – 10°C or at 35°C or higher.

6. When the adapter is not in use or when being maintained and inspected, disconnect the power cord of the adapter from the receptacle.

7. Never short-circuit the rechargeable battery. Short-circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery.

8. Do not handle the adapter’s power plug with wet hands. Doing so may result in electric shock.

9. Avoid dangerous environment. Don’t expose power tools and adapter to rain. Don’t use power tools and adapter in damp or wet locations. And keep work area well lit. Never use power tools and adapter near fl ammable or explosive materials. Do not use tool and adapter in presence of fl ammable liquids or gases.

10. Do not dispose of the adapter in fi re. If the adapter is burnt, it may explode.

11. Never disassemble the adapter.

12. Do not use the product if the tool or the adapter terminals (battery mount) are deformed. Installing the adapter could cause a short circuit that could result in smoke emission or ignition.

13. Keep the tool’s terminals (battery mount) free of swarf and dust. Prior to use, make sure that swarf and dust have not collected in the area of the terminals. During use, try to avoid swarf or dust on the tool from falling on the adapter. When suspending operation or after use, do not leave the tool in an area where it may be exposed to falling swarf or dust. Doing so could cause a short circuit that could result in smoke emission or ignition.

14. Do not pierce adapter with a sharp object such as a nail, strike with a hammer, step on, throw or subject the adapter to severe physical shock.

15. Do not use an apparently damaged or deformed adapter.

16. Do not use the adapter in reverse polarity.

17. Keep work area clean. Cluttered areas and benches invite accidents.

18. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
    Children should be supervised to ensure that they do not play with the appliance.

19. Store idle tools and adapter. When not in use, tools and adapter should be stored in dry, high or locked-up place — out of reach or children. Store tools and adapter in a place in which the temperature is less than 40°C.

20. Don’t abuse cord. Never carry AC/DC adapter by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp edges.

21. Take good care of the AC/DC adapter.
    Prior to use, inspect the plug and cord of the AC/DC adapter. If there is any damage, contact the place of purchase for repairs.

22. For repairs, use a store that specializes in AC/DC adapters.
    Persons other than a service person should not take apart, repair or modify the AC/DC adapter.
    Doing so could result in injury from fi re or malfunction. If there are any abnormalities to the AC/DC adapter, send it out to be inspected or repaired.
    Do not modify this AC/DC adapter as it conforms to applicable safety standards.
    Always contact the place of purchase for repairs. Repairing the adapter yourself could result in accident or injury.

23. The product has built-in precision parts. Avoid dropping or infl icting strong impact.
    Doing so may cause malfunction.

24. Make sure that the adapter is installed fi rmly. If it is as all loose it could come off and cause an accident.

25. Periodically inspect the product.

26. Do not use the product if the tool or the AC/DC adapter terminals (AC/DC adapter mount) are deformed. Installing the AC/DC adapter could cause a short circuit that could result in smoke emission or ignition.

27. Keep the tool’s terminals (AC/DC adapter mount) free of swarf and dust.

    • Prior to use, make sure that swarf and dust have not collected in the area of the terminals.
    • During use, try to avoid swarf or dust on the tool from falling on the AC/DC adapter.
    • When suspending operation or after use, do not leave the tool in an area where it may be exposed to falling swarf or dust.
    • Doing so could cause a short circuit that could result in smoke emission or ignition.

28. To prevent electric shock, connect to a power source equipped with a ground fault circuit breaker.

29. Prior to use, make sure that the DC cord insulation is not torn or that the case is not cracked.
    Do not use the product if there is a break in the DC cord, the insulation is torn, or the case is damaged.

30. Before starting operation, make sure that the vicinity of the box’s vent is free from any wood shavings or iron powder.
    Also, do not use in locations where iron powder is abundant, or in areas where there is rain, snow or other water sources that could wet the product.

31. Make sure there are no solid metal material or liquid in the adapter box. Failure to do so may result in damage.

32. Be careful not to step on the box. Also, make sure the box is placed in a location where it won’t be stepped on. Do not place in a location where the box could be immersed in water when it rains.

33. The adapter, power supply box and the inside of the DC cord generates a boosted high voltage of 380 V so please be careful of the following.

    • Do not disassemble the product.

    • Do not drop or expose to impact.
      In the event the product is damaged from strong impact, do not use the product.

    • Do not use the product in areas exposed to rain, snow, iron powder or wet condition.

    • Do not touch the product with wet hands.

    • Do not spill or pour liquid onto the product.

    • Do not pull the cord with excessive force.

    • Use the product in a well-ordered work environment.

34. When the temperature protective feature frequently cuts the power off , do not overload the machine with continued work, but let the machine rest for a little
    before continuing operation.

35. The machine does get hot. However, this does not indicate an abnormality.
    Keep the electricity running and operate the internal fan to cool the machine before carrying it elsewhere.

36. During use, do not pull the cord to move the Box. Doing so may result in damage.

37. Do not use more that a single cord reel of 30 meters. Doing so may result in damage.

38. During use, if the machine stops running after the Box’s LED lamp blinks, confi rm the power supply environment.

39. Do not drag the cord when using or carrying the machine.
    Doing so may tear the cord insulation or break the cord which could result in electric shock.

40. Do not stretch the cord out any more than required. When using tools such as gardening clippers or circular saws, always make sure of the power cord’s position to avoid cutting the cord during operation.

41. To use the AC/DC adapter after it shuts down due to high temperature, disconnect the box’s power plug, wait for the LED lamp to go out and then reconnect the box’s power plug. If the machine cuts off even after sufficiently cooling it off with the built-in fan, discontinue use as there may be a problem with the machine.

42. Do not use this product near a radio. Doing so could cause noise from the radio, making it diffi cult to listen to a broadcast.

43. This is a power source for multi-volt products. Do not use with 18 V products or chargers. Doing so could result in damage.

44. Overload behavior may diff er when compared with BSL36B18 battery use.
    With the battery where the LED should blink on the main unit, the LED on the AC/DC adapter may blink instead.

45. Do not use this product near a pacemaker or other similar implanted device, which may be aff ected by a magnetic fi eld produced by this product.

PRECAUTIONS FOR AC/DC ADAPTER
The adapter equips with the protection function to stop the output. In the cases of 1 to 2 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function.

1. If the tool is overloaded, output may stop. In this case, release the switch of tool and eliminate causes of overloading.
2. If the adapter is overheated under overload work, output may stop.
   In situations like this, discontinue use of the adapter and detach it from the tool. Allow the adapter to cool in a location such as a shaded area with good air circulation. After that, you can use it again.

NAMES OF PARTS (Fig. 1 – Fig. 2)

1. Outlet plug
2. AC cable
3. Error lamp
4. Box ! Power lamp
5. DC cable
6. Ventilation holes
7. Error lamp
8. Adapter
9. Terminal
10. Latch
11. Power lamp
12. Professional 36V products compatible with multi volt battery
13. Product not compatible with multi volt battery

SYMBOLS
WARNING: The following show symbols used for the machine. Be sure that you understand their meaning before use.

APPLICATION
DC power supply for professional 36V product compatible with multi volt battery

SPECIFICATION

volt battery
Weight| Adapter : 0.8 kg Box : 1.2 kg

For details, see our general catalog or other related information.

MOUNTING AND OPERATION

INDICATION OF THE INDICATOR LAMP

MAINTENANCE AND INSPECTION

1. Inspecting the mounting screws
   Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard.

2. Cleaning of the adapter
   When the adapter is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics.

3. Inspection of terminals (tool and battery)
   Check to make sure that swarf and dust have not collected on the terminals.
   On occasion check prior, during and after operation.
   CAUTION Remove any swarf or dust which may have collected on the terminals. Failure to do so may result in malfunction.

4. Store idle adapter
   When not in use, the adapter should be stored in dry, high or locked-up place — out of reach of children.

CAUTION: In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

NOTE: Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.

TROUBLESHOOTING GUIDE

WARNING

• To avoid injury from an accidental start, turn the switch OFF and remove the plug from the power source and remove the AC/DC adapter from the tool before making any adjustments.
• All electrical or mechanical repairs should be done only by qualifi ed service technicians. Contact HiKOKI Authorized Service Center.

Cannot be attached to the main unit
Does not operate| ●   Used with a 14.4 V/18 V product

●   Used with a 36 V product that is incompatible with a multi volt battery.

| Use with a 36 V product that is compatible with multi volt battery.
Suddenly stops| The tool or the AC/DC adapter became overheated| Allow the tool and the AC/DC adapter to fully cool.
The tool was overloaded| Remove the cause of the overload.
Frequently stops| Protection function activated due to consecutive use with high workloads.| Not a problem. Avoid high workloads when operating unit.
Overheating caused by the box or adapter’s ventilation hole being blocked by obstructions such as cloth or wood scraps| Remove any obstructions blocking the ventilation hole to allow air to reach the box and adapter.
The box’s error lamp blinks and comes to a halt| Box at high temperature| Disconnect the box’s power plug and allow the box to fully cool.
Problem with power source| Use of multi-outlet or single outlet extension cords may cause insufficient voltage. Use a power source capable of providing a voltage of 100 V.

When the power source is disconnected, allow over 30 seconds to pass before reconnecting.

The adapter is hot| Heats up with continuous use| Continue with electric conduction and allow the unit to fully cool by fan or in a shaded area with good air circulation.
Something is wrong with the operation of the overload protection function| Overload protection function’s activation conditions vary when using a battery as opposed to using an AC/DC adapter| Not a problem. To protect the unit, avoid overload during operation.

GUARANTEE CERTIFICATE

1. Model No.
2. Serial No.
3. Date of Purchase
4. Customer Name and Address
5. Dealer Name and Address
   (Please stamp dealer name and address)

Hikoki Power Tools Deutschland GmbH
Siemensring 34, 47877 willich, Germany
Tel: +49 2154 49930
Fax: +49 2154 499350
URL: http://www.hikoki-powertools.de

Hikoki Power Tools Netherlands B.V.
Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands Tel: +31 30 6084040
Fax: +31 30 6067266
URL: http://www.hikoki-powertools.nl

Hikoki Power Tools (U.K.) Ltd.
Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom
Tel: +44 1908 660663
Fax: +44 1908 606642
URL: http://www.hikoki-powertools.uk

Hikoki Power Tools France S.A.S.
Parc de l’Eglantier 22, rue des Cerisiers, Lisses-C.E. 1541, 91015 EVRY CEDEX, France
Tel: +33 1 69474949
Fax: +33 1 60861416
URL: http://www.hikoki-powertools.fr

Hikoki Power Tools Belgium N.V./S.A.
Koningin Astridlaan 51, B-1780 Wemmel, Belgium Tel: +32 2 460 1720
Fax: +32 2 460 2542
URL http://www.hikoki-powertools.be

Hikoki Power Tools Italia S.p.A
Via Piave 35, 36077, Altavilla Vicentina (VI), Italy Tel: +39 0444 548111
Fax: +39 0444 548110
URL: http://www.hikoki-powertools.it

Hikoki Power Tools lbérica, S.A.
C/ Puigbarral, 26-28, Pol. Ind. Can Petit, 08227 Terrassa (Barcelona), Spain
Tel: +34 93 735 6722
Fax: +34 93 735 7442

URL: http://www.hikoki-powertools.es

Hikoki Power Tools Österreich GmbH
IndustrieZentrum NÖ –Süd, Straße 7, Obj. 58/A6 2355 Wiener Neudorf, Austria
Tel: +43 2236 64673/5
Fax: +43 2236 63373
URL: http://www.hikoki-powertools.at

Hikoki Power Tools Norway AS
Kjeller Vest 7, N-2007 Kjeller, Norway Tel: (+47) 6692 6600
Fax: (+47) 6692 6650
URL: http://www.hikoki-powertools.no

Hikoki Power Tools Sweden AB
Rotebergsvagen 2B SE-192 78 Sollentuna, Sweden
Tel: (+46) 8 598 999 00
Fax: (+46) 8 598 999 40
URL: http://www.hikoki-powertools.se

Hikoki Power Tools Denmark A/S
Lillebaeltsvej 90, 6715 Esbjerg N, Denmark
Tel: (+45) 75 14 32 00
Fax: (+45) 75 14 36 66
URL: http://www.hikoki-powertools.dk

Hikoki Power Tools Finland Oy
Tupalankatu 9, 15680 Lahti, Finland
Tel: (+358) 20 7431 530
Fax: (+358) 20 7431 531
URL: http://www.hikoki-powertools.fi

Hikoki Power Tools Hungary Kft.
1106 Bogáncsvirág u.5-7, Budapest, Hungary
Tel: +36 1 2643433
Fax: +36 1 2643429
URL: http://www.hikoki-powertools.hu

Hikoki Power Tools Polska Sp. z o. o.
Gierdziejewskiego 1
02-495 Warszawa, Poland
Tel: +48 22 863 33 78
Fax: +48 22 863 33 82
URL: http://www.hikoki-narzedzia.pl

Hikoki Power Tools Czech s.r.o.
Modřická 205, 664 48 Moravany, Czech Republic
Tel: +420 547 422 660
Fax: +420 547 213 588
URL: http://www.hikoki-powertools.cz

Hikoki Power Tools Romania S.R.L.
Ring Road, No. 66, Mustang Traco Warehouses, Warehouse No.1, Pantelimon City, 077145, Ilfov County, Romania
Tel: +40 371 135 109
Fax: +40 372 899 765
URL: http://www.hikoki-powertools.ro

References

• Strona główna | HIKOKI
• HiKOKI Power Tools Österreich - High Performance Power Tools
• Home Banner
• Home - Hikoki-powertools.cz
• HiKOKI Power Tools Deutschland - High Performance Power Tools
• HiKOKI Power Tools
• HiKOKI Power Tools Ibérica - HiKOKI
• Hikoki powertools
• HiKOKI - High Performance Power Tools
• HiKOKI Power Tools
• HiKOKI Power Tools
• HiKOKI
• HiKOKI Power Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>