ANKEWAY AW1003 Android car Radio User Manual
- June 5, 2024
- ANKEWAY
Table of Contents
ANKEWAY AW1003 Android car Radio
Wiring Diagram and Define
Instructions for use
For the sake of your safety, please don’t watch the video while driving and operating a machine; Please dispatches the volume to clearly while driving to the voice of the outside world. Before the operation, please read this manual and other manual sys·tem, and understand the use of manual and machine-related safety tips and warning signs, after reading in a, readily accessible place for ready reference.
- Pay attention to traffic safety in the first place.
- If you meet difficulty in operating the system, please again after he parked his car in a safe place.
- Don’t let children operate this machine, lest cause personal injury and damage to the machine.
- Please follow the traffic rules when using the satellite navigation function to drive.
- Please do not ban the use of electronic equipment or it is forbidden to use open flame, such as gas stations, breweries, strong electromagnetic interference region, otherwise may cause danger.
- Don’t maintenance, maintenance, installation of the machine itself. Under ·the condition of the plug do not install or repair the machine, by not trained in electronic equipment or vehicles accessories installation personnel or the lad of experience installation and maintenance of this machine is very dangerous.
- Do not install the machine storage or in direct sunlight place, don’t put it in other harmful material environments, especially the LCD screen, if the installation of the LCD screen is in the air conditioner Near the duct, please keep cool and hot air blows directly to 1he machine, otherwise lit may damage the machine, even on the bus or persona I injury.
- Please do not use some sharp objects painted screen, and don’t use hard objects to press the screen, otherwise, will cause damage to the display or touch screen.
- In order to guarantee the normal operation of the machin<“, and prevent the occurrence of fire or get a,n electric shock, please don’t expose machine in damp air, more can’t liquid drying machine.
Tips and warnings:
In order to in order to emphasize the important information of user man1: ee
this tag should pay special attention to, it said some important warning and
prompt information.
Safety note
Please read all instructions before installation and suggested by car audio
professional installation of the machine.
The machine is suitable for car 12v power supply system (must have grounding
line), please do not install the machine in 24 v car, otherwise, it will
damage the machine.
In no professional guidance, not to replace the power fuse, use only a fuse of
the improper, can cause the damage of the machine and cause a fire.
In order to avoid the violation of traffic rules, the driver shall not
watching while driving and operating the machine, lest produce unnecessary
accidents.
For safety and ensure that the product normal use, please to the professionals
of this product installation, disassembly or repair the machine by yourself,
lest cause the machine damage and accidents, for details please contact with
the local professional car audio store.
Please prevent this product in a humid environment and the water, in order to
avoid short circuits caused by electric shock, or other unnecessary damage and
fire happened. \
Note: in order to prevent it short out, before the installation, please remember that the car stall and breaking the ACC connected to B+.
Machine reset
- The first use of the system before or after the replacement battery, the machine must be reset.
- When the machine function is not normal, the machine must be reset.
- Click restore factory Settings in system Settings interface, make the machine is in the factory the initial state.
- Use a pointed object, press the RESET button on the panel, or click the system RESET in the system Settings, the machine will be RESET to turn it off, back to the factory the initial state.
Note: press the RESET button and the system initialization will lose time and set the value before.
User Manual
Special Warm Note
All cables are labeled. The integrated end is connected to the serial
interface on the back of the radio. The decentralized end is connected to the
car cable. If your car’s original ISo cable is not compatible with this
device, you need to buy an adapter cable compatible with your model for
wiring. You can also remove the original Iso serial interface of your car
before wiring.
Main Cable Wiring Diagram
RL/RR/FL/FR: to 4 speakers.
ANT-CONT: to Antenna (No antenna no wiring).
Lamp Control: to car front small light.
Back: to rear camera signal in cable.
KEY1(KEY2): Use only one of the cables to connect the signal output cable
of the car’s SVWC. “KEY1″is not compatible, select”KEY2”.
GND: to battery negative/iron ground.
B+: to car battery positive.
ACC: to car ignition detection cable.
Video/Audio/Amplifier/WiFi/BT/MIC
FRONT R/L OUT: Connect to the amplifier Audio Input
Special Note: Whether you need the Rear Camera or not, you must connect
the “CAMERA” Cable to the 10-pin port on the back of the radio to ensure that
the radio gets better WiFi and Bluetooth signals.
Reversing Camera Wiring Diagram
Wiring A: Combine the “short red cable” with the Back” cable and connect
to the car reVerse detection cable.
Wiring B: Combine the two “short red cables” and connect to the positive
pole of the car’s taillight.
Wiring C: Connected to the radio reversing video input port (10-pin)
Side Button Debugging & Calibration
Must be corrected when first used or the buttons fail
- Debugging Method:
- Step 1: Turn on the radio, press and hold the screen with 5 fingers until 4 “round options” appear. Then click on the 4 “round options” (from 1 to 4).
- Step 2: Click the “Start” option will turn red and start calibration.
- Step 3 : Click the “Power” option will turn red and then click the power button on the left side of the screen. If “Power” returns to black, the calibration was successful. Then use the same method to correct the remaining buttons. Click the “Close” option after the calibration is completed.
Side Button Debugging and Calibration
Tips for 4 – 5- 6- 7- 8
Click the “Power” option will turn red and then click the power button on the
left side of the screen. If “Power” returns to black, the calibration was
successful. Then use the same method to correct the remaining buttons.
Click the “Close” option after the calibration is completed
Android Settings
Android Settings
Go to settings for “Language /DaTe &Time /WiF i/…”
language and time settings
How to Connect Bluetooth
- Radio Bluetooth Name: Car BT
- BT connection Pin: 0000
- Connected: “Red” phone name
- Failed: “Blue” phone name
- Search / Remove connectable devices
EQ & Speakers Settings
- EQ: Pop / Jazz / Rock / Classic / Custom
- Speakers Settings: Custom / Default
GPS Navigation
- iGO
- Google Maps
- “iGO” App
- Europe Map Offline Data
SWC Settings / Learning / Correction
Tips:
Just select one of the cables “KEY1” and “KEY2” to connect to the SWC (Select
a compatible cable). You need to connect the two cables if you have two SWC.
SWC Debugging:
- Step 1: Click “Settings” to find the “Steering Learn” for the SWCsystem.
- Step 2: Press the control button on your car’s steering wheel and don’t let go, then click the corresponding control button on the screen to complete the debugging. Then debug the next button.
- Step 3: After you finish debugging
ANKEWAY External Steering Wheel Control
- ANKEWAY (ANKEWAYUK) Store sells an external Steering Wheel Control that is perfectly compatible with Android radio.
- We recommend you to buy it and fix it on the steering wheel.
- Connect the “KEY1” and “KEY2” cables of the external steering wheel control to the “KEY1” and “KEY2 ” of the radio.
- The red cable is connected to the “ACC” of the radio, and the black cable is connected to the “GND” of the radio.
Easy Connection for Mirror-link
- Download and install App “Easy Connection” for Android phones (Google Play).
- iPhone does not need to install this App.
How to Connect and Use (for Android Phone)
Step-1, Install Google Assistant for voice command.
Step-2, Connect the radio and mobile phone via USB (or WiFi) to play
video.
Step-3, Connect the radio and mobile phone via Bluetooth to play audio.
Step-4, Click App “Easy Connection” on the phone and radio.
Step-5, Follow the App operation prompt to complete Mirror-link.
How to Connect and Use (for iPhone)
Step-1, Connect the radio and mobile phone via USB (or WiFi).
Step-2, Click App “Easy Connection” on the radio.
Step-3, Follow the operation prompt to complete Mirror-link.
Trust
Enter the Screen Password
Factory Settings
Password: 8888
- Tips： It is not recommended to restore the factory settings if not necessary
- Software Settings
- Hardware Settings
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>