KARCHER K5 Power Control Car & Home Pressure Washer User Manual
- June 5, 2024
- Karcher
Table of Contents
K5 Power Control Car & Home Pressure Washer
K 5 Power Control
English
Register your product
www.kaercher.com/welcome
59695920 (02/21)
A
2
B
C
D
E
F
G
H
I
3
3
J
K
L
M
N
O
P
Q
4
4
Contents
Safety instructions ……………………………………….. 5
KÄRCHER Home & Garden app ……………………. 6
Environmental protection………………………………. 6
Intended use……………………………………………….. 6
Accessories and spare parts …………………………. 7
Scope of delivery …………………………………………. 7
Description of the device ………………………………. 7
Safety devices …………………………………………….. 7
Symbols on the device …………………………………. 7
Assembly ……………………………………………………. 8
Initial startup ……………………………………………….. 8
Operation……………………………………………………. 9
Transport ……………………………………………………. 10
Storage………………………………………………………. 10
Care and service …………………………………………. 10
Troubleshooting guide ………………………………….. 11
Technical data …………………………………………….. 11
Declaration of Conformity ……………………………… 12
EU Declaration of Conformity ………………………… 12
Safety instructions
Read this safety chapter and these original instructions before using the
device for the first time. Act in accordance with them. Keep the original
instructions for future reference or for future owners. In addition to the
notes in the operating instructions, you also need to take into consideration
the general safety regulations and accident prevention guidelines applicable
by law. Warnings and information notices attached to the device provide
important information for hazard-free operation.
Hazard levels
DANGER
Indication of an imminent threat of danger that will lead to severe injuries
or even death.
WARNING
Indication of a potentially dangerous situation that may lead to severe
injuries or even death.
CAUTION
Indication of a potentially dangerous situation that may lead to minor
injuries.
ATTENTION
Indication of a potentially dangerous situation that may lead to damage to
property.
Protective gear
CAUTION Wear suitable protective clothing
and safety goggles to protect yourself from water or dirt backsplash. Aerosols
can be formed when using highpressure cleaners. Inhaling aerosols can be
harmful for your health. Depending on the application, the use of fully
shielded nozzles (e.g. surface cleaners) can significantly lower the emission
of aqueous aerosols. Depending on the environment to be cleaned, wear a
suitable respiratory protective mask of class FFP 2 or comparable to protect
yourself from inhaling aerosols if the use of a fully shielded nozzle is not
possible.
General safety instructions
DANGER Risk of asphyxiation. Keep pack-
aging film out of the reach of children.
WARNING Only use the device for its proper
use. Take into account the local conditions and beware of third parties, in
particular children, when working with the device. Persons with reduced
physical, sensory or mental capabilities and persons lacking experience and
knowledge may only use the appliance if they are properly supervised, have
been instructed on use of the appliance safely by a person responsible for
their safety, and understand the resultant hazards involved. Children must not
operate the device. Children must be supervised to prevent them from playing
with the appliance.
CAUTION Safety devices are provided for
your own protection. Never modify or bypass safety devices.
Risk of electric shock
DANGER Only connect protection class I de-
vices to properly earthed power sources. Only connect the device to
alternating current. The voltage indicated on the type plate must match the
voltage of the power source. Only operate the device via a fault current
protection switch (maximum 30 mA). Never touch the mains plug and socket with
wet hands. The mains plug and coupling of the extension cable must be water
tight and may not be placed in water. The coupling may not be on the floor.
Use cable drums to ensure that the sockets are at least 60 mm above the floor.
All live parts in the work area must be protected against water jets.
WARNING Only connect the device to an
electrical connection which has been set up by a qualified electrician as per
IEC 60364-1. Check that the mains connection cable with mains plug is
undamaged each time before using the device. To avoid any possible danger, a
damaged mains connection cable must be immediately replaced by the
manufacturer, or the authorised customer service department or a qualified
electrician. Do not damage the power supply and extension cable by running
over it, crushing or yanking it or similar. Protect the power supply cable
from heat, oil and sharp edges. Unsuitable electrical extension cables are
dangerous. Only use approved and appropriately marked electrical extension
cables with a sufficient line cross section when outdoors: 1-10 m : 1.5 mm2,
10-30 m : 2.5 mm2
CAUTION Always fully unwind the extension
cable from the cable drum. In case of longer breaks in operation and after
use, switch off the device at the main switch / device switch and pull the
mains plug.
Operation
DANGER Operation in explosive atmos-
pheres is prohibited. Never suction solvents, liquids containing solvents or
undiluted acids. This includes e.g. petrol, paint thinner or heating oil. The
spray mist is highly flammable, explosive and poisonous. Damaged wheels / tyre
valves are extremely dangerous. Damaged wheels / tyre valves can be damaged by
the high-pressure jet and explode. The first sign of this is discolouration of
the tyres. Keep a spray distance of at least 30 cm when cleaning the wheels /
tyre valves.
English
5
WARNING Do not use the device if people
without the proper protective clothing are in its reach. Do not aim the high-
pressure jet at yourself, e.g. to clean clothes or shoes. Do not direct the
high-pressure jet at persons, animals, live electrical equipment or at the
device itself. Do not spray any objects which contain harmful substances (e.g.
asbestos). Check the device and the accessories, such as the high-pressure
hose, high-pressure gun and safety devices, to make sure they are in proper
safe and reliable condition before each operation. Do not use the device if it
is damaged. Replace damaged components immediately. Only use high-pressure
hoses, control panels and couplings specified by the manufacturer. Risk of
scalding. When disconnecting the supply or high-pressure hose, hot water can
leak out of the connections after operation.
CAUTION According to the applicable regu-
lations, the appliance may never be used with the drinking water network
without a system separator. Ensure that the connection to your house water
system, with which the high-pressure cleaner is operated, is equipped with a
system separator according to EN 12729 type BA. Water that has flowed through
a system separator is no longer classified as drinkable. Never leave the
device unsupervised while it is in operation. Recoil force from the water
stream emerging at the high-pressure nozzle acts on the high-pressure gun.
Keep proper footing and hold the high-pressure gun and spray lance firmly.
Accidents or damage due to the device falling over. Before all actions with or
on the device, you must make sure that it is stable.
ATTENTION Do not operate the device at tem-
peratures below 0 °C.
Operation with detergent
WARNING Incorrect use of detergents can
cause serious injuries or poisoning.
CAUTION Keep the detergent out of the
reach of children. Only use the detergents supplied or specified by the
manufacturer. The use of other detergents or chemicals can impair the safety
of the device.
Care and service
WARNING Always pull out the mains plug
before all care and maintenance work.
CAUTION Have repair work and work on
electrical components carried out by the authorised customer service only.
ATTENTION Do not use acetone, undiluted ac-
ids or solvents, as they corrode the materials used on the device.
Transportation
CAUTION
Risk of accidents and injuries. Take into account the weight of the device for
transportation and storage. See chapter Technical data in the operating
instructions.
KÄRCHER Home & Garden app
The KÄRCHER Home & Garden app contains: Installation and initial startup
information Information about the areas of application Tips & Tricks FAQ with
detailed troubleshooting Connection to the KÄRCHER Service Centre The app can
be downloaded here:
Trademarks Google PlayTM and AndroidTM are trademarks or
registered trademarks of Google Inc. Apple® and App store® are trademarks or
registered
trademarks of Apple Inc.
Environmental protection
The packing materials can be recycled. Please dispose of packaging in
accordance with the environmental regulations. Electrical and electronic
appliances contain valuable, recyclable materials and often components such as
batteries, rechargeable batteries or oil, which – if handled or disposed of
incorrectly – can pose a potential danger to human health and the environment.
However, these components are required for the correct operation of the
appliance. Appliances marked by this symbol are not allowed to be disposed of
together with the household rubbish. Cleaning work producing in oily waste
water, e.g. washing engines, washing undercarriages etc., may only be
performed at washing stations with an oil separator. Working with detergents
may only be performed on watertight surfaces with connection to the waste
water sewage system. Do not allow detergent to enter waterways or the soil.
Extraction of water from public waterways is not permitted in some countries.
Notes on the content materials (REACH) Current information on content
materials can be found at: www.kaercher.de/REACH
Intended use
Use the high-pressure cleaner in private households only. The high-pressure
cleaner is intended for cleaning machines, vehicles, buildings, tools,
façades, terraces, garden machines etc. using a high-pressure water jet.
6
English
Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the
appliance will run fault-free and safely. Information on accessories and spare
parts can be found at www.kaercher.com.
Scope of delivery
The scope of delivery for the appliance is shown on the packaging. Check the
contents for completeness when unpacking. If any accessories are missing or in
the event of any shipping damage, please notify your dealer.
Description of the device
The maximum amount of equipment is described in these operating instructions.
Depending on the model used, there are differences in the scope of delivery
(see packaging). For the illustrations, refer to the graphics page
Illustration A
1 Stand with carrying handle
2 Water connection with integrated sieve
3 Transport wheel
4 Visor
5 Hose guide
6 Trigger “0/OFF” / “I/ON”
7 Storage for spray lance
8 High-pressure hose
9 *Plug ‘n’ Clean detergent bottle
10 Storage / parking position for high-pressure gun
11 Transport handle, telescoping
12 Power Control spray lance dirt grinder for stubborn dirt, pressure level:
HARD
13 Vario Power Power Control spray lance for the most common cleaning tasks,
pressure levels: HARD / MEDIUM / SOFT / MIX
14 Power Control high-pressure gun
15 Button for separating the high-pressure hose from the high-pressure gun
16 High-pressure gun lever
17 Pressure indicator (0-MIX / 1-SOFT / 2-MEDIUM / 3-HARD)
18 High-pressure gun lock
19 Carrying handle
20 Hose holder
21 Type plate
22 Accessory compartment
23 Hook for net attachment
24 Accessory compartment net
25 Mains connection with mains plug
26 Water connection coupling
27 Garden hose with commonly available coupling
Fabric reinforced Diameter of at least 1/2 inch (13 mm) Length at least
7.5 m
28 KÄRCHER suction hose for water supply from open containers (order no.
2.643-100.0)
29 Supplied screws and dowels
30 Foam nozzle with detergent container The detergent is sucked out of the
container to produce a strong detergent foam.
31 Rotating washing brush (e.g. for washing cars)
- optional, ** additionally required
Supplied screws and dowels
Illustration B
1 Stand dowels (2 pieces)
2 Screw M 4×20 (2 pieces)
3 Screw M 4×22 (2 pieces)
4 Screw M 4×16 (8 pieces)
Safety devices CAUTION
Missing or modified safety devices Safety devices are provided for your own protection. Never modify or bypass safety devices.
Power switch
The power switch prevents unintentional operation of the device.
High-pressure gun lock
The lock locks the lever of the high-pressure gun and prevents the device from starting unintentionally.
Auto-stop function
If the lever of the high-pressure gun is released, the pressure switch turns off the pump and the high-pressure jet stops. The pump switches on again when the lever is pressed.
Motor circuit breaker
The motor circuit breaker shuts off the device if power consumption it too high.
Symbols on the device
Do not aim the high-pressure jet may at persons, animals, live electrical equipment or the device itself. Protect the device against frost. The device may not be connected to the public drinking water network.
English
7
Assembly
For the illustrations, refer to the graphics page. Place the screws provided
and matching screwdriver at the ready. Fit the supplied loose parts onto the
device before starting up the device.
Fitting the wheels
1. Insert the wheels. Note Pay attention to the alignment of the hole.
Illustration C 2. Secure the wheels with 1 screw each.
Mounting the stand
1. Insert the stand. Illustration D
2. Insert the 2 dowels into the holes as far as they will go.
3. Secure the base with 2 screws.
Installing the spray lance storage
1. Hang the spray lance storage in position. 2. Secure the storage with 2
screws.
Illustration E 3. Secure the cover with 4 screws.
Illustration F
Mounting the transport handle
1. Attach the transport handle. Illustration G
2. Secure the transport handle with 2 screws.
Mounting the accessory net
1. Hang the accessory net on the hooks. Illustration H
Push the high-pressure hose through the hose guide
1. Insert the high-pressure hose through the hose guide from the rear.
Illustration I
Installing the water connection coupling
1. Screw the water connection coupling onto the water connection on the
device. Illustration J
Initial startup
1. Place the device on a flat and level surface. 2. Unwind the high-pressure
hose completely and
eliminate any loops and twists. 3. Pull the high-pressure hose all the way
forwards
through the hose guide. 4. Insert the high-pressure hose into the high-
pressure
gun until it audibly latches into place. Note Take care to ensure the correct
alignment of the nipple.
Illustration K 5. Check for a secure connection by pulling on the
high-pressure hose. 6. Plug the mains plug into a mains socket.
Water supply
For the connection values, see the type plate or chapter Technical data.
Observe the water distribution company regulations.
ATTENTION
Damage through contaminated water Contamination in the water can damage the
pump and the accessories. KÄRCHER recommends using the KÄRCHER water filter
for protection(special accessory, order number 4.730-059).
Connection to the water line
ATTENTION
Hose coupling with Aquastop on the water connection of the device Damage to
the pump Never use a hose coupling with Aquastop on the water connection of
the device. You can use an Aquastop coupling on the tap. 1. Plug the garden
hose onto the water connection
coupling. 2. Connect the garden hose to the water line. 3. Open the water tap
fully.
Illustration L
Sucking water from open containers
When used with the KÄRCHER suction hose with check valve (special accessory,
order number 2.643-100) this high-pressure cleaner is suitable for sucking up
surface water, e.g. from rain barrels or ponds (for the maximum suction height
see chapter Technical data). The water connection coupling is not required for
vacuuming operation. 1. Fill the suction hose with water. 2. Screw the suction
hose onto the device water con-
nection and hang it in a water source (e.g. water butt).
Vent the device
1. Switch the device on “I/ON”. 2. Unlock the lever of the high-pressure gun.
3. Press the lever of the high-pressure gun.
The device switches on. 4. Allow the device for run a maximum of 2 minutes un-
til the water escaping from the high-pressure gun is free of air bubbles. 5.
Release the lever of the high-pressure gun. 6. Lock the lever of the high-
pressure gun.
8
English
Operation
ATTENTION
Pump running dry Damage to the device If pressure does not build up in the
device after 2 minutes then switch the device off and proceed according to the
instructions in chapter Troubleshooting guide.
Power Control System
The pressure indicator on the high-pressure gun shows the currently set
pressure level when operating with a Power Control spray lance. Note The
sensitivity of materials can vary greatly depending on age and condition. The
recommendations are therefore not binding. Note When operating with surface
cleaner and other accessories, the pressure indicator is not accurate.
Display
Pressure level HARD
MEDIUM
Recommended for e.g.
Stone terraces made of paving stones or washed concrete, asphalt, metal
surfaces, garden utensils (wheelbarrow, spade, etc.)
Cars / motorcycles, brick surfaces, plastered walls, plastic furniture
SOFT
Wooden surfaces, bicycle, sandstone surfaces, rattan furniture
MIX
Operation with detergent
High-pressure operation
ATTENTION
Damage to painted or sensitive surfaces Surfaces can be damaged when the jet
is too close to the surface or an unsuitable spray lance is used. Maintain a
minimum spray distance of 30 cm when cleaning painted surfaces. Do not clean
car tyres, paint or sensitive surfaces such as wood with the dirt grinder. 1.
Insert a spray lance into the high-pressure gun and
lock it by turning it 90°. Illustration M 2. Switch the device on (“I/ON”). 3.
Unlock the lever of the high-pressure gun. 4. Press the lever of the high-
pressure gun. The device switches on. 5. Turn the Vario Power Power Control
spray lance until the required pressure level is shown on the pressure
indicator.
Operation with a washing brush
ATTENTION
Paint damage Damage to surfaces through a dirty brush Ensure that the washing
brush is free from dirt or other particles before using it. Note The device
operates at low pressure when using washing brushes. This means that detergent
can be mixed with the water. 1. Insert the washing brush into the high-
pressure gun
and turn by 90° to fasten it.
Operation with detergent
DANGER
Failure to adhere to the safety data sheet Incorrect handling of the detergent
can seriously damage your health Observe the safety data sheet of the
detergent manufacturer, in particular the instructions on personal protective
equipment. Note Detergent can only be mixed into the jet at low pressure. Note
A Plug n’ Clean detergent bottle is required for operating with detergent. KÄRCHER detergent can be purchased ready to use in a Plugn’ Clean detergent
bottle. 1. Remove the cover from the Plug n’ Clean detergent bottle. 2. Plug the detergent bottle into the Plugn’ Clean de-
tergent connection with the opening facing down. Illustration N 3. Use the
Vario Power spray lance. 4. Turn the spray lance towards “MIX” until “MIX” is
displayed on the high-pressure gun. The detergent solution is mixed with the
water jet during operation. 5. You can optionally use the foam nozzle. a Fill
the detergent solution into the detergent tank.
Adhere to the dosage specifications on the detergent container. b Connect the
foam nozzle to the detergent container. c Insert the foam nozzle into the
high-pressure gun and turn by 90° to fasten it. Illustration O
Recommended cleaning method
1. Spray the detergent sparingly on the dry surface and let it work for a
while (do not let it dry).
2. Rinse off the loosened dirt with the high-pressure jet.
After operation with detergent
1. Pull the Plug `n’ Clean detergent bottle out of the mount and close it
with the cap before transporting the device lying down.
2. Store the detergent bottle in the holder with the lid facing up.
3. Flush the device with clear water for approx. 30 seconds.
English
9
Interrupting operation
1. Release the lever of the high-pressure gun. The device switches off when
the lever is released. The high pressure in the system is retained.
2. Lock the lever of the high-pressure gun. Illustration P
3. Place the high-pressure gun with the spray lance in the parking position.
4. Switch the device off “0/OFF” during work breaks longer than 5 minutes.
Ending operation
CAUTION
Pressure in the system Injuries from high-pressure water escaping
uncontrollably Only disconnect the high-pressure hose from the highpressure
gun or the device when the system is fully depressurised. 1. Release the lever
of the high-pressure gun. 2. Close the water tap. 3. Press the lever of the
high-pressure gun for 30 sec-
onds. The pressure remaining in the system is discharged. 4. Release the lever
of the high-pressure gun. 5. Lock the lever of the high-pressure gun. 6.
Disconnect the device from the water supply. 7. Switch off the device “0/OFF”.
8. Pull the mains plug out of the socket.
Transport
CAUTION
Failure to observe the weight Risk of injury and damage Be aware of the weight
of the device during transportation.
Carrying the device
1. Lift and carry the device by the carrying handles.
Pulling the device
1. Pull the transport handle out until it audibly latches into place.
2. Pull the device via the transport handle.
Transporting the device in a vehicle
1. Before transporting lying down, pull the Plug `n’ Clean detergent bottle
out of the mount and close it with the cap.
2. Secure the device against slipping and tipping over.
Storage
CAUTION
Failure to observe the weight Risk of injury and damage Be aware of the weight
of the device during storage.
Storing the device
1. Place the device on a level surface. 2. Disconnect the spray lance from
the high-pressure
gun. 3. Press the separation button on the high-pressure
gun and disconnect the high-pressure hose from the high-pressure gun. 4. Store
the high-pressure hose on the device. 5. Store the mains connection cable and
accessories on the device. Observe the additional notes before storing the
device for a long period of time, see chapter Care and service.
Frost protection
ATTENTION
Danger of frost Incompletely emptied devices can be destroyed by frost.
Completely empty the device and accessories. Protect the device from frost.
The following requirements must be satisfied: The device is disconnected from
the water supply. The high-pressure gun is disconnected from the
high-pressure hose. 1. Switch the device on “I/ON”. 2. Wait for a maximum of 1
minute until no more water
escapes from the high-pressure hose. 3. Switch off the device. 4. Store the
device in a frost-protected room, together
with all accessories.
Care and service
DANGER
Danger of electric shock Injuries due to touching live parts Switch off the
device. Remove the mains plug. The device is maintenance-free, i.e. you do not
need to perform any maintenance work.
Clean the sieve in the water connection
ATTENTION
Damaged sieve in the water connection Damage to the device through
contaminated water Check the sieve for damage before inserting it in the water
connection. If necessary, clean the sieve in the water connection. 1. Remove
the water connection coupling. 2. Pull the sieve out using flat pliers. 3.
Clean the sieve under running water.
Illustration Q 4. Insert the sieve into the water connection.
10
English
Troubleshooting guide
Malfunctions often have simple causes that you can remedy yourself using the
following overview. When in doubt, or in the case of malfunctions not
mentioned here, please contact your authorised Customer Service.
DANGER
Danger of electric shock Injuries due to touching live parts Switch off the
device. Remove the mains plug. Device not running 1. Press the lever of the
high-pressure gun.
The device switches on. 2. Check that the voltage specified on the type plate
corresponds to the voltage of the power source. 3. Check the mains connection
cable for damage. 4. If the motor is overloaded and the motor circuit
breaker has triggered: a Switch off the device “0/OFF”. b Allow the device to
cool down for 1 hour. c Switch the device on “I/ON” and resume opera-
tion. Have the device checked by Customer Service if this fault occurs
repeatedly. The device does not start up, the motor buzzes Voltage drop due to
a weak mains grid or when using an extension cable 1. When switching on, first
press the lever on the highpressure gun and then switch on the device “I/ON”.
Device does not reach required pressure The water supply is too low 1. Open
the water tap fully. 2. Check the water inlet for an adequate flow rate. The
sieve in the water connection is dirty. 1. Pull the sieve in the water
connection out using flat pliers. 2. Clean the sieve under running water. Air
is in the device. 1. Vent the device: a Switch on the device without a
connected spray
lance for a maximum of 2 minutes. b Press the high-pressure gun and wait until
the
water escaping from the high-pressure gun is free of air bubbles. c Connect
the spray lance. d Observe the maximum suction height during suction operation
(see chapter Technical data). Strong pressure fluctuations 1. Clean the high-
pressure nozzle: a Use a needle to remove dirt from the nozzle drill. b Rinse
the high-pressure nozzle from the front with water. 2. Check the water supply
volume. Device leaking 1. The device leaks a small amount for technical
reasons. If the leak is severe, request authorised Customer Service. Detergent
is not sucked in 1. Use the Vario Power spray lance and turn it to “MIX”. 2.
Check that the Plug `n’ Clean detergent bottle is sitting correctly with the
opening facing down in the detergent connection.
Warranty
The warranty conditions issued by our relevant sales company apply in all
countries. We shall remedy possible malfunctions on your appliance within the
warranty period free of cost, provided that a material or manufacturing defect
is the cause. In a warranty case, please contact your dealer (with the
purchase receipt) or the next authorised customer service site. (See overleaf
for the address)
Technical data
Electrical connection
Voltage
V
230-240
Phase
~
1
Frequency
Hz
50
Power rating
kW
2,1
Degree of protection
IPX5
Protection class
I
Power protection (slow-blowing) A
13
Water connection
Feed pressure (max.)
MPa 1,2
Input temperature (max.)
°C
40
Input amount (min.)
l/min 10
Suction height (max.)
m
0,5
Device performance data
Operating pressure
MPa 12,5
Max. permissible pressure
MPa 14,5
Water flow rate
l/min 7,5
Maximum flow rate
l/min 8,3
Detergent flow rate
l/min 0,3
High-pressure gun recoil force N
20
Dimensions and weights
Typical operating weight
kg
14,8
Length
mm 402
Width
mm 306
Height
mm 588
Determined values in acc. with EN 60335-2-79
Hand-arm vibration value
m/s2 <2,5
Uncertainty K
m/s2 0,6
Sound pressure level LpA
Uncertainty KpA
Sound power level LWA + K uncertaintyWA
dB(A) 75 dB(A) 3 dB(A) 91
Subject to technical modifications.
English
11
Declaration of Conformity
We hereby declare that the product described below complies with the relevant
provisions of the following UK Regulations, both in its basic design and
construction as well as in the version put into circulation by us. This
declaration shall cease to be valid if the product is modified without our
prior approval.
Product: High-pressure cleaner Type: 1.324-xxx
Currently applicable UK Regulations S.I. 2008/1597 (as amended) S.I. 2016/1091
(as amended) S.I. 2012/3032 (as amended) S.I. 2001/1701 (as amended)
Designated standards used EN 60335-1 EN 60335-2-79 EN 62233: 2008 EN 55014-1:
2017 EN 55014-2: 2015 EN 61000-3-2: 2014 EN 61000-3-3: 2013 EN IEC 63000: 2018
Applied conformity assessment procedure S.I. 2001/1701 (as amended): Schedule
8
Sound power level dB(A) Measured: 88 Guaranteed: 91 The undersigned act on
behalf and under the power of attorney of the company management.
EU Declaration of Conformity
We hereby declare that the machine described below complies with the relevant
basic safety and health requirements in the EU Directives, both in its basic
design and construction as well as in the version placed in circulation by us.
This declaration is invalidated by any changes made to the machine that are
not approved by us.
Product: High-pressure cleaner Type: 1.324-xxx
Currently applicable EU Directives 2006/42/EC (+2009/127/EC) 2014/30/EU
2011/65/EU 2000/14/EC
Harmonised standards used EN 60335-1 EN 60335-2-79 EN 62233: 2008 EN 55014-1:
2017 EN 55014-2: 2015 EN 61000-3-2: 2014 EN 61000-3-3: 2013 EN IEC 63000: 2018
Applied conformity evaluation method 2000/14/EG: Annex V
Sound power level dB(A) Measured: 88 Guaranteed: 91 The undersigned act on
behalf and under the power of attorney of the company management.
H. Jenner Chairman of the Board of Management
S. Reiser Director Regulatory Affairs & Certification
Documentation supervisor: S. Reiser Alfred Kärcher SE & Co. KG Alfred-Kärcher- Str. 28 – 40 71364 Winnenden (Germany) Ph.: +49 7195 14-0 Fax: +49 7195 14-2212 Winnenden, 2021/01/01
H. Jenner Chairman of the Board of Management
S. Reiser Director Regulatory Affairs & Certification
Documentation supervisor: S. Reiser Alfred Kärcher SE & Co. KG Alfred-Kärcher- Str. 28 – 40 71364 Winnenden (Germany) Ph.: +49 7195 14-0 Fax: +49 7195 14-2212 Winnenden, 2021/01/01
12
English
230-240 1
50 2,1 IPX5
I 13
1,2 40 10 0,5
12,5 14,5
7,5 8,3 0,3 20
14,8 402 306 588
<2,5 0,6 75 3 91
V
~
Hz
kW
A
()
MPa
()
C°
()
l/min
()
m
()
MPa
MPa
l/min
l/min
l/min
N
kg
mm
mm
mm
EN 60335-2-79
m/s2
m/s2
K
dB(A) dB(A) dB(A)
LpA KpA
+ LWA KWA
.
. .1 . .2 . . .1 . .2
. : .1
a .
b . . c
d .( ) : .1
. a . b . .2
. .1 .
.”MIX” Vario Power .1 Plug `n’ Clean .2
.
.
. . ( )
14
. .
. :
. .
.”I/ON” .1 .2
. . .3
.4 .
. . .
.
. . .1 . .2
. .3 Q
. .4
.
.
. .
. .1
. .2
. . .3 .4
: .”OFF/0″ a . b . “I/ON” c
.
. .1
.”I/ON”
. .1
. . .2
P .3
. 5 .4
.”OFF/0″
. . .1 . .2
. 30 .3 . . .4 . .5
. .6 .”OFF/0″ .7
. .8
.
. .1
. .1 . .2
‘Plug `n .1 . Clean . .2
.
. .1 . .2 .3
. . .4 . .5
.
15
.
.1 .°90 M
.(“I/ON”) .2 . .3 . .4
. Vario Power Power Control .5 .
.
. .
.1 .°90
.
.
Plug n’ Clean KÄRCHER . .Plugn’ Clean .Plug n’ Clean .1 .2 .Plugn’ Clean N
.Vario Power .3 “MIX” “MIX” .4
. .
. .5 . a
. . b c
.°90 O
.1 .( )
. .2
Plug .1 . n’ Clean`
.2 .
. 30 .3
) KÄRCHER (2.643100 )
.( .
. .1 .2
.( )
.”I/ON” .1 . .2 . .3
. .4
. . .5 . .6
.
Power Control
Power
.Control
. .
.
) (.
HARD
/
MEDIUM
SOFT
MIX
. 30
.
16
. .1 D . .2 . .3
. .1 . .2 E
. 4 .3 F
. .1 G
. .2
. .1 H
.1 . I
.1 .
J
. .1 . .2 .3
. .4
.
. K
. .5 . .6
.
.
. KÄRCHER
.(059-4.730 ) KÄRCHER
Aquastop
Aquastop .
. Aquastop . .1
. .2 . .3 L
27
( 13) 1/2
7.5
KÄRCHER 28 (100.0-2.643 )
29
- 30
.
( ) * 31
B
(2 ) 1
(2 ) M 4×20 2
(2 ) M 4×22 3
(8 ) M 4×16 4
.
.
.
.
.
.
.
. .
.
. . .
. .1
. C
. .2
17
.
.
. .www.kaercher.com
. .
.
. .( ) A
1
2
3
4
5
“OFF” / “I/ON/0” 6
7
8
- 9
/ 10
11
Power Control 12 HARD :
Vario Power Power Control 13 / HARD : MEDIUM / SOFT / MIX
Power Control 14
15
16
-MIX / 1-SOFT / 2-MEDIUM / 3-0) 17 (HARD
18
19
20
21
22
23
24
25
26
.
.
.
. .
KÄRCHER Home & Garden App
: KÄRCHER Home & Garden App
KÄRCHER :
TM TM
.Google Inc ® ®
.Apple Inc
. .
. .
.
. . .
. (REACH) :
www.kaercher.de/REACH
18
.IEC 60364-1 .
.
. . .
2 2,5 : 30-10 2 1,5 : 10-1 :
.
. /
.
.
. / . / .
. .
. 30 . /
. . . .( )
. . . . .
.
. .EN 12729 Typ BA . .
. . .
.
.° 0
.
.
.
.
. .
.
.
.
.
.
.
.
. . / .
( ) .
FFP 2 .
.
.
.
.
. . .
.
.
I
. .
. .( 30) . . .
. 60
.
19
!
THANK YOU!
MERCI! DANKE! GRACIAS!
vielen Vorteilen. advantages.
avantages. Registre su producto y aproveche de muchas ventajas.
www.kaercher.com/welcome
Bewerten Sie Ihr Produkt und sagen Sie uns Ihre Meinung. Rate your product and
tell us your opinion. Évaluer votre produit et dites-nous votre opinion.
Reseñe su producto y díganos su opinión.
www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG Alfred-Kärcher-Str. 28-40 71364 Winnenden (Germany)
Tel.: +49 7195 14-0 Fax: +49 7195 14-2212
References
- Cleaning equipment and pressure washers | Kärcher International
- Dealer Search | Kärcher International
- Home and Garden Warranty Registration USA - Kärcher
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>