Volantexrc P-51D 400mm 4-Inch Beginner RC Warbird Plane User Manual

Volantexrc P-51D 400mm 4-Inch Beginner RC Warbird Plane

WARNING

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product.

CAUTION: Procedures, if not properly followed, is able to create a possibility of physical property damage AND or the possibility of injury. Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, and personal property and cause serious injury. This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not attempt to disassemble, use incompatible components or augment the product in any way without the approval of VolantexRC Co., Ltd. This manual contains instructions for safety, operation, and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup, or use, in order to operate correctly and avoid damage or serious injury. Age Recommendation: Not for children under 14 years. This is not a toy.

Safety Precautions

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others.

• Always ensure all batteries have been properly charged before using the vehicle.
• Always check all servos and their connections prior to each run.
• Never operate your vehicle near spectators, parking areas or any other area that could result in injury to people or damage of property.
• Never operate your vehicle during adverse weather conditions. Poor visibility can cause disorientation and loss of control of your vehicle.
• Never point the transmitter antenna directly toward the vehicle. The radiation pattern from the tip of the antenna is inherently low.
• If at any time during the operation of your vehicle you observe any erratic or abnormal operation, immediately stop operation of your vehicle until the cause of the problem has been ascertained and corrected.

Battery Usage & Charging Warnings

CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-Po/ Li-Ion/Ni-Mh batteries can result in fire, personal injury, and/or property damage.

• The battery charger included with your plane(if there be) is designed to safely balance and charge the specific Li-Po/Li-Ion/Ni-Mh battery
• By handling, charging or using the included battery, you shall assume all risks associated with Li-Po/Li-Ion/Ni-Mh battery.
• If at any time the battery begins to balloon or swell, discontinue use immediately. If charging or discharging, you should discontinue and disconnect. Continue to use, charge or discharge a battery that is ballooning or swelling can result in fire.
• Always store the battery at room temperature in a dry area for best results.
• Always transport or temporarily store the battery in a temperature range of 40-120 Fahrenheit degrees (5-49 degrees centigrade). Do not store the battery or your plane in a car or in direct sunlight. If stored in a hot car, the battery can be damaged or even cause fire.
• Always charge a battery away from flammable materials.
• Always inspect the battery before charging and never charge damaged batteries.
• Always disconnect the battery after charging, and allow the charger to cool before the next charge.
• Always constantly monitor the temperature of the battery pack while charging.
• ONLY USE A CHARGER SPECIALLY DESIGNED TO CHARGE SPECIFIC BATTERIES.
• Never discharge Li-Po cells till below 3V under load.
• Never cover waning labels with hook or loop strips.
• Never leave charging batteries unattended.
• Never charge batteries outside recommended levels.
• Never attempt to dismantle or alter the charger.
• Never allow minors to charge battery packs.
• Never charge batteries in extremely hot or cold places(recommended between 40-120 Fahrenheit degrees / 5-49 degrees centigrade) or in direct sunlight.

Box Contents

NOTE: The actual product may vary slightly from the manual according to the model you purchase.

Charging Instruction

1. Unplug the battery from your plane.
2. Carefully plug the charger into the USB port on your computer or USB adapter.
3. Connect battery into the charger.
4. The charging process takes about 3 hours. For safety reasons, never charge the battery for longer than 4 hours. While charging, the red LED indicator will be flashing. When the charging is finished, the red LED will be off.

Setup Instruction

• Install 4 AA batteries(not included) in the transmitter.

• Plug the landing gears into the position on the main wing as shown above.

• Connect the battery to the receiver, then stick the battery into the cabin.

• The setup is done. Make sure you read and follow all instructions in this manual before starting flying the airplane.

Center Control Surfaces

NOTE: Keep the X-PILOT switch off (manual mode) before you operate the steps below. See more information in the “X-PILOT switch” section.

With the transmitter turned on and the battery connected to the ESC(and installed in the battery compartment), it is now possible to check the center of all control surfaces.

Observe the rudder to ensure it is properly centered as shown above.

If the rudder is angled off to the right or left, adjust the push rod by its arc-shaped section slightly, making sure the rudder is properly centered.

Then observe the elevator to ensure it is properly centered as shown above. If the elevator is angled off to the upper or lower position, adjust the push rod by its arc-shaped section slightly, making sure the elevator is properly centered.

If the aileron is angled off to the upper or lower position, adjust the push rod by its arc-shaped section slightly, making sure the aileron is properly centered.

Transmitter Instruction

X-PILOT Switch

The airplane comes with a pre-installed X-PILOT to help control flying easily. The switch is with 3 levels to control the X-PILOT. To turn on the X-PILOT, switch to upper position(towards you). To turn off the X-PILOT, switch to lower position(away from you).
CAUTION: It is strongly suggested to turn on X-PILOT while flying the airplane.

Binding Instruction

Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. When a receiver is bound to a transmitter, the receiver will only respond to that specific transmitter. If you need to rebind for any reason, please follow these steps:

1. Keep the transmitter switched OFF, throttle joystick at buttom position.

NOTICE: Keep X-PILOT switch at Middle or Beginner position.

NOTICE: Keep the plane still in a calm environment for calculating the X-PILOT.

1. 2.Connect the battery to the plane, then turn on the transmitter within 5 seconds.
2. The receiver LED will flash for 3-8 seconds to bind automatically.
3. After the receiver LED stop flashing, it means the binding process is done.

Follow below steps when you operate a bound plane:

1. Power on transmitter first.
2. Connect the battery to the plane within 3 seconds.
3. The receiver LED in plane will flash and then turn to solid in several seconds.
4. Switch the X-PILOT control stick to X-PILOT assist level(MIDD or BEGINNER).

NOTICE: Allow the airplane stay still about 3~5 seconds in a calm environment when you first time turn on X-PILOT, in order to calibrate and activate the X-PILOT. When the X-PILOT starts to react, means it is activated. 5.Turn throttle stick up to max and then down to min to arm the motor. CAUTION: Do NOT operate around people or property, otherwise it may cause serious damage!

Throttle Unlock(Arming)

To prevent from damage, the throttle channel is locked each time when powering on your transmitter. Follow below instruction to unlock the throttle.
CAUTION: Keep the propeller in distance for your safety. Turn the throttle stick up to max position until you hear a “beep” sound. Then turn the throttle stick down to min position until you hear a “beep” sound. Now the throttle is unlocked.

Digital Trims

Digital trims allow to adjust the centered position of aileron, rudder or elevator hinge. Each time when a trimmer is moved, the servo output will change one angle. If the trimmer is held, the output will scroll in that direction until the trimmer is released or the output reaches its end. When you hear a short “beep” sound, it means the trimmer is centered.

Channels Reactions Checking

Place your plane in a neutral position, and follow the below steps to check the channel reactions. Move the sticks(except the throttle stick) to see if all servo surfaces react correctly as shown in the left diagram(left throttle for example). Swing your plane to check if all servo surfaces react correctly as shown in the right diagram.

One-key Aerobatics Instruction

The one-key aerobatics feature allows beginner pilot to perform aerobatic actions by simply pressing the button on transmitter. During flight, under X-PILOT control mode, press the onekey aerobatics button, the transmitter will beep several times. During the beeping, simply move the aileron stick to either direction for auto-roll. Or move the elevator stick to either direction for auto-flip.

One-key U-turn Instruction

The airplane comes with one-key U-turn function, which enable the plane to U-turn in the opposite direction that the airplane takes off. Follow below steps to activate the function.

1. Place your plane heading to the take-off direction.
2. Do NOT unlock the throttle, press the activation button and hold for several seconds until you hear a “beep” sound, the rudder surface will respond, meaning the one-key U-turn function is now activated.

NOTICE: Every time when you power on the plane, it requires to activate the one-key U-turn function. To use this function during flight, press the one-key U-turn switch button,the plane will turn around automatically, back to the opposite direction where it takes off. To quit, just press again the switch button, or control any servo stick(rudder/elevator), the plane will back to your control immediately.No matter you flies the plane under manual control or X-PILOT assist mode when you turn on the one-key U-turn function, the plane will enter X-PILOT assist mode automatically to help stably flying back. When you quit this function, the airplane will back to the control mode it was.

CAUTION: This function is bound to the receiver, instead of to the transmitter, which means the plane will U-turn ONLY to the opposite direction that the plane takes off. It also means when the plane U-turns and passes the position where you activated the function, the one-key U-turn function will NOT U-turn the plane back to the take-off position.

X-PILOT System Calibration

1. Turn the throttle stick to min position.
2. Power on the transmitter and the receiver.
3. Do NOT unlock the throttle.
4. Keep the sticks as above picture for several seconds.
5. When you hear a “beep” sound, it means the X-PILOT system is calibrated based on the horizontal level you are keeping it.

Propeller Saver Instruction

The propeller saver keeps the propeller from damage and prevents the electronic components from overcurrent. When the airplane hits an obstacle, the propeller will lose the base. To install the propeller back to the base, insert the upper part centerly through the motor shaft, and hear a “click” sound to ensure it is secured.

Propeller Replacement

Follow below steps to replace broken propeller and shaft adaptor. You will need help of a Philips screw driver and pliers(not included).

1. Take off the spinner and propeller by loosen the screw with a Philips screw driver.
2. Take off the shaft adaptor carefully. If it is too tight, use pliers to help.
3. Replace any part broken.
4. Install all parts back by inverted orders to finish the replacement.

Power System Replacement

• Take off the cover in the head of fuselage to replace the motor, or the cover in the middle of fuselage to replace the receiver. It is no need of tool to take off the covers

• Follow below steps to replace the receiver.

  • Loosen the screws of servo horns, take the servo horns off.
  • Unplug the motor cable and the mainwing servo cable. You may need to record the direction of cable plugs.
  • Loosen the screws as shown to take off the receiver.

• Follow below steps to replace the motor.

  • Unplug the motor cable from receiver board. You may need to record the direction of the cable plug.
  • Loosen the screws as shown to take off the the motor.

Flight Checklist

NOTE: This checklist is NOT intended to replace the content included in this instruction manual. Althought it can be used as a quick start guide, we strongly suggest that read all though the manual completely before proceeding.

• Ensure the throttle control stick is at bottom position before connecting the battery.
• Fly the model(hand-launch or take off from a flat/level surface).
• Land the model on a flat/level surface.
• Unplug the battery.
• Always turn off the transmitter last.

Find a Flight Field

Based on the size and weight of the plane it is typically considered to be a “park flyer” class airplane. As a result, it is best to fly the plane at a local park, schoolyard, flying field, or another area that is large enough and free of people and obstructions. We recommend an area the size of at least one football/soccer field. However, even larger areas are better suited and preferred especially when learning how to fly. Do NOT fly in parking lots, crowded neighborhood areas, or in areas that are not free of people or obstructions. NOTE: This checklist is NOT intended to replace the content included in this instruction manual. Although it can be used as a quick start guide, we strongly suggest that read the manual completely before proceeding. – Ensure the throttle control stick is at the bottom position before connecting the battery. – Fly the model(hand-launch or take off from a flat/level surface). – Land the model on a flat/level surface. – Unplug the battery. – Always turn off the transmitter last. Flight Checklist 3. Follow the below steps to replace the motor. a. Unplug the motor cable from the receiver board. You may need to record the direction of the cable plug. c. Loosen the screws as shown to take off the motor. Screws We also suggest flying over the grass as it is a much more forgiving surface that causes less damage in the unfortunate event of a crash. Short grass is better for takeoffs and landings as grass that is too long can cause the airplane to nose over/flip and be damaged. An ideal flying area allows for takeoffs and landings on a smoother surface(such as asphalt) and flying over grass.

Fly in the spacious ground without obstacles and boskage. Never fly the plane near highways, railways, high tension lines, crowded people, flying areas,s, and residential areas. NOTE: The plane is designed to be flown outdoors only.

Flying Conditions

It is typically best to fly on days that are calm without wind, especially when learning how to fly. It is strongly suggested to fly only in calm conditions until you are familiar with the controls and handling of the model. Even light winds can make it much more difficult to learn to fly, and in some cases can even carry the model beyond your line of sight. Also, if you are a first-time or low-time pilot, we highly recommend that allow a more experienced pilot to test fly and properly trim the model before attempting your first flight. A proven flyable and properly trimmed model is significantly easier and more enjoyable to fly. After you have properly trimmed the airplane in calm conditions and become familiar with its handling/capabilities you will be able to fly in light winds or depending on your experience and comfort level, in winds up to 5-7 mph. Do NOT fly on days when significant moisture, such as rain or snow, is present.

FCC compliance statement

This device complies with Part 15 of the FCC Rules. 0perat ion is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FOC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. his equipment generates, uses, and can radiate rad1o frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following Deasures8:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>