ARIKASEN A5 Wireless Headphone User Manual

ARIKASEN A5 Wireless Headphone

For user’s safety, please read this manual before using the headset.

• The following matters should be paid attention to when using headset:
• Please avoid long- time use of high volume mode, because it will lead to hearing loss caused by noise.
• If you are in bad condition of potential danger please stOp using neadset, in order to ensure sarety.
• Users should reasonably control the volume and time when listening to the headset.
• The volume should not be too high,otherwise you can’t hear the VoIce around. If volume is too high that may appear tinnitus, please lower down the volume.
• Don’t drive while listening to songs.
• Use dry soft cloth to dean the headset! Should avoid the headset into the water, that will cause headset damage.
• If you feel obvious discomfort, stimulation, or other adverse reaction when using the headsetstop using it immediately.
• The headset should not be stored or used in temperatures below 20°c (-4°F) or higher than 55°C (131°F),otherwise will reduce the battery life.

Details of products

ON/Off

1. Power On:
   • Press MFB for 3 seconds
   • Blue light is on
   • Power on
2. Power OFF:
   • Press MFB for 4 seconds
   • ORed light is on
   • power off

Connect with mobile phone

1. Long press MFB button for 5 seconds, headset enters the pairing state
2. Blue and red light
3. flashes alternately
4. Pairing
5. Turn on your Bluetooth device on your mobile phone.
6. Find the headset name of “A5″ to geting connect in your list,headset prompts” Your headset is connected”

Connect with two phones

1. Turn off Bluetooth on mobile and headset
2. Connect with econd mobile phone
3. Turn on phone 1 Bluetooth and select A5 gets connected

Insert external microphone

insert the microphone when playing games for better Voice communication experience
(According to the final product you bought)

Starting Gaming Mode

(In standby mode or listening to music)

Music Control

• Short press
• Play/Pause

previous
Long press button to select previous song

next track
Long press +button to select next song

increase volume
Short press + button to increase volume

decrease volume
Short press button to decrease volume

Management Calls

1. Answer/ Hang up
   Short press answer and end call

2. reject call
   Double press reject call

3. Last number redial
   Double Press el Last Number Ledial

4. Smart voice U
   Long press1 second, to activate intelligent voice

Factory Reset

• In charging State
  Press once , then long press 2 seconds

• The red and blue lights flash two times

Charging indicator

Charging red light is often on, full then red light off

Battery warning

• do not disassemble, collide, squeeze or throw it into fire.
• If there is serious bloating, do not continue to use it.do not place it in high temperature.
• Prohibiting to use the battery after soaking in water.

Technical Index

• Correspond with: V5.0
• Support: HSP. HFP A2DP. AVRCP
• Transmittig Power: Class 2
• Working Distance Range: 10m
• Frequency Range: 2.402GHz-2.48OGHz
• Charge Time: 2.5 hours
• Music Time: 218 hours
• Standby Time: 2160 hours
• USB power supply: $5V/1A

In order to extend the life of the headphones, when replacing the sponge, please follow the steps below.
The steps to replace sponge cover

1. Put your hand in the gap between the earphone and the sponge cover
2. Reverse the force evenly around until disassembled
3. Take out the accessory from the sponge then replace new sponge on the accessory
4. take the sponge accessory’s buckling position to the earphoen’s buckle place and squeeze hard until it is installed

FCC Warning Statement

Changes or moditications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult thee dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>