ECOFLOW 2000 DELTA Max portable power station User Manual
- June 5, 2024
- ECOFLOW
Table of Contents
EcoFlow DELTA Max
User Manual
DISCLAIMER
Read all safety tips, warning messages, terms of use, and disclaimers
carefully. Refer to the terms of use and disclaimer at https://ecoflow
.compagesterms-of-use and stickers on the product before use. Users take full
responsibility for all usage and operations. Familiarize yourself with the
related regulations in your area. You are solely responsible for being aware
of all relevant regulations and using EcoFlow products in a way that is
compliant.
Specifications
1.1 Specifications of DELTA Max (2000)
General Info
Net Weight | Approximately 48lbs |
---|---|
Dimensions | 19.6×9.5x12in |
Capacity | 2016Wh 50.4V |
Wi-Fi | Supported |
Output Ports
AC (x6)
Max Device(s) Power Supported by X-Boost
USB-A (x2)
USB-A Fast Charge (x2)
USB-C (x2)
Car Charger
DC5521 Output (x2)| Pure Sine Wave, 2400W total (surge 5000W),
120V~ 60Hz
3400W
5V 2.4A 12W Max, per port
5V 2.4A 9V 2A 12V 1.5A 18W Max, per port
5/9/12/15/20V 5A 100W Max, per port
12.6V 10A, 126W Max
12.6V 3A, per port
---|---
- Car charger shares power with the DC5521 output port, offering a maximum output of 126W.
Input Ports
AC Charge
AC Input Voltage
Solar Charger
Car Charger| X-Stream Fast Charge 1800W Max, 15A
100-120V~ 50Hz/60Hz
11-100V 13A, 800W Max
Supports 12V/24V Battery, Default 8A
---|---
Battery Info
Cell Chemistry
Cycle Life
Protection
| NCM
800 cycles to 80%+ capacity
Over Voltage Protection, Overload Protection, Over
Temperature Protection, Short Circuit Protection,
Low-Temperature Protection, Low Voltage Protection, Overcurrent Protection
---|---
Environmental Operating Temperature
Optimal Operating Temperature
Discharge Temperature
Charge Temperature
Storage Temperature| 68°F to 86°F(20°C to 30°C)
-4°F to 113°F (-20°C to 45°C)
32°F to 113°F(0°C to 45°C)
-4°F to 113°F (-20°C to 45°C) (optimal: 68°F to 86°F [20°C to 30°C])
---|---
- Whether the product can be charged or discharged depends on the actual temperature of the battery pack.
Additional Connections
Smart Extra Battery
Smart Generator| Supports up to 2 DELTA Max Smart Extra Batteries
(sold separately)
Supported (sold separately)
---|---
Safety Instructions
2.1 Usage
- Do not use the product near a heat source, such as a fire source or a heating furnace.
- Avoid contact with any liquid. Do not immerse the product in water or get it wet. Do not use the product in rain or humid environments.
- Do not use the product in an environment with strong static electricity/magnetic fields.
- Do not disassemble the product in any way or pierce the product with sharp objects.
- Avoid using wires or other metal objects that may result in a short circuit.
- Do not use unofficial components or accessories. If you need to replace any components or accessories, please visit the official EcoFlow channels to check relevant information.
- When using the product, please strictly follow the operating environment temperature specified in this user manual. If the temperature is too high, it may result in a fire or explosion; if the temperature is too low, the product performance may be severely reduced, or the product may cease to work.
- Do not stack any heavy objects on the product.
- Do not lock the fan forcibly during use or place the product in an unventilated or dusty area.
- Please avoid impact, falls, or severe vibrations when using the product. In case of a severe external impact, turn off the power supply immediately and stop using the product. Ensure the product is well fastened during transportation to avoid vibrations and impacts.
- If you accidentally drop the product into the water during use, please place it in a safe open area, and stay away from it until it is completely dry. The dried product should not be used again and should be properly disposed of according to Section 2.2 below. If the product catches fire, we recommend that you use the fire extinguishers in the following order: water or water mist, sand, fire blanket, dry powder, and finally a carbon dioxide fire extinguisher.
- Use a dry cloth to clean off dirt on the product ports.
- Rest the product on a flat surface to avoid damages caused by the product falling over. If the product is overturned and severely damaged, turn it off immediately, place the battery in an open area, keep it away from combustible matter and people, and dispose of it in accordance with local laws and regulations.
- Ensure that the product is kept out of reach of children and pets.
- Store the product in a dry and ventilated place.
- It is recommended to use moisture barrier bags in wet environments (for example, places by the sea or waterways) to prevent the product from getting soaked. If water is found inside the product, it must not be used or turned on again. Please take Anti-electric shock measures before touching the product. Following this, place the product in a safe, waterproof, and open area. Once complete contact EcoFlow Customer Service immediately.
- This product is not recommended for powering medical emergency equipment related to personal safety, including but not limited to medical-grade ventilators (hospital version CPAP: Continuous Positive Airway Pressure), artificial lungs (ECMO, Extracorporeal Membrane Please follow your doctor’s instructions and consult with the manufacturer for restrictions on the use of the equipment. If used for general medical equipment, please be sure to monitor the power status to ensure that the power does not run out.
- When in use, power supply products will generate electromagnetic fields, which are likely to affect the normal operation of medical implants or personal medical equipment such as pacemakers, cochlear implants, hearing aids, defibrillators, etc. If these types of medical equipment are being used, please contact the manufacturer to inquire about any restrictions on the use of such equipment. These measures are fundamental to ensure a safe distance between the medical implants (for example, pacemakers, cochlear implants, hearing aids, defibrillators, etc.) and this product while in use.
- When the power supply is connected in normal mode to a refrigerator, power fluctuations may cause the power supply to automatically shut down. When connecting the power supply to a refrigerator that stores medicine, vaccines or other valuable items, it is recommended to set the AC output to “Always on” in the app. This helps support a continuous power supply and ensures a safe and efficient power consumption state.
2.2 Disposal Guide
- If conditions permit, make sure that the battery is fully discharged before disposing of it in a designated battery recycling bin. The product contains batteries with potentially dangerous chemicals, so it is strictly prohibited to dispose of it in ordinary trash cans. For more details, please follow the local laws and regulations on battery recycling and disposal.
- If the battery cannot be fully discharged due to a product failure, please do not dispose of the battery directly in the battery recycling box. In such case, you should contact a professional battery recycling company for further processing.
- Please dispose of over-discharged batteries that cannot be recharged.
Getting Started
3.1 Product Details
3.2 LCD Screen
Battery Level Indicator: The indicator will repeatedly fill while charging. If the product is at 0% charge, the indicator will flash to warn you. Wi-Fi Status: After pressing the IOT button for 3 seconds, the Wi-Fi status will flash on the LCD screen which indicates that the product is ready for pairing. There’re two ways to connect the product with the App, either directly connect to the product’s hotspot or using the Internet. If the App is successfully connected to the product’s hotspot, the icon will keep flashing; if it is successfully connected to the Internet, the icon will stay on. * See Section 5 for more troubleshooting steps.
3.3 General Product Usage
Product On, Product Off, LCD Screen On
Short press the Main Power Button to turn on the product; the LCD Screen will
light up and the battery level indicator icon will display. The product enters
sleep mode after 5 minutes of idle operation; the LCD Screen will
automatically turn off. When the product senses any load change or operations,
the LCD Screen will automatically light up. To turn the LCD Screen on or off,
please short press the Main Power Button. To power off the product, press and
hold the Main Power Button. The default product standby time is 2 hours. With
other Power, Buttons turned off and no other load access for 2 hours, the
product will automatically shut down. The standby time can be set on the App.
USB Output Port
With the Main Power Button turned on, short press the USB Power Button to use
the USB Output Port. Short press the USB Power Button again to turn it off.
With the USB Power Button on, the product will not automatically shut down.
12V DC Output Port
With the Main Power Button turned on, short press the 12V DC Power Button to
use the 12V DC Output port. Short press the 12V DC Power Button again to turn
it off.
With the 12V DC Power Button on, the product will not automatically shut down.
AC Output Port
With the Main Power Button turned on, short press the AC Power Button to use
the AC Output ports. Short press the AC Power Button again to turn it off. The
default standby time of the AC Output port is 12 hours. Without any load
access for 12 hours, the AC power will automatically turn off. Please turn off
the AC power button when not in use to save power consumption.
3.4 AC Charging
EcoFlow’s X-Stream fast charge technology is specifically designed for AC
charging. You can control the charging power through the AC Charge Speed
Switch. When set to the top, you will have the maximum charging speed. When
set to the bottom it’ll be at your custom speed, which is 400W by default,
customizable in the EcoFlow App. In case of unusual situations where the AC
input current remains higher than 20A, the X-Stream charging input port will
initiate a self-protection function, and the Overload Protection Switch on the
product will automatically pop up. After confirming that there is no product
failure, you can press the Overload Protection Switch to resume charging.
The charging power can be adjusted through the AC Charge Speed Switch on the back of the product. You can set the charging power range in the EcoFlow App. Please use EcoFlow AC charging Cable for fast charging. AC Charging Cable should directly plug into 15A(or above) wall outlet. EcoFlow takes no responsibility for any consequences caused by failures to follow instructions, including but not limited to charging with AC charging Cable.
3.5 Solar Charging
Users can connect solar panels in series as shown in the figure to recharge
the product.
*Solar charging cable (MC4-XT60 adapter cable) is supplied separately.
When using an EcoFlow solar panel to charge the product, please follow the
instructions that come with the solar panel.
Before connecting the solar panel, please ensure that the solar panel’s output
voltage is within 100V to avoid product damage.
3.6 Car Charging
Users can recharge the product through the Car Charging Input Port. It
supports 12V/24V car chargers and an 8A default charging current. Please
charge using the car charger after you’ve started the car to avoid failure to
start due to insufficient car battery. In addition, please make sure that Car
Charging Input Port and the Car Charging Cable are in good condition. EcoFlow
takes no responsibility for any losses or damages caused by failures to follow
instructions.
3.7 Using Smart Extra Battery
The product can be connected with up to two Smart Extra Batteries at the same
time to meet higher capacity needs. Please refer to the user manuals of DELTA
Max Smart Extra Battery and Smart Generator for detailed instructions.
Extra Battery, please follow the instructions below:
1. Before connecting the product to a Smart Extra Battery, please make sure
that both the product and the Smart Extra Battery are turned off.
2. After connecting the product to a Smart Extra Battery, please make sure
that both of their LCD screens display an extra battery icon before using it.
3. Do not directly connect or remove the Smart Extra Battery during charging
and discharging processes. If you need to connect or remove it midway, please
turn off the product first.
4. Do not touch the metal terminals of the Smart Extra Battery connector with
your hands or other objects. If foreign objects adhere to the metal terminals,
please gently wipe them with a dry cloth.
3.8 APP
The EcoFlow App gives users the ability to control and monitor EcoFlow power
stations remotely. Read the EcoFlow App user guide and access the download
link here: https://ecoflow.compagesecoflow-app
Privacy Policy
By using EcoFlow Products, Applications and Services, you consent to the
EcoFlow Term of Use and Privacy Policy, which you can access via the “About”
section of the “User” page on the EcoFlow App or on the official EcoFlow
website at https://ecoflow.compagestermsofuse
and https://ecoflow.compageprivacy-
policy
3.9 X-Boost
To avoid operation failure due to overload protection, the X-Boost feature
will be automatically enabled when the total output exceeds the rated output
power, which enables the product to power high wattage appliances at the rated
output power.
X-Boost Tips:
1. X-Boost is enabled by default; you can enable or disable it in the EcoFlow
App.
2. X-Boost is not available when the AC output is turned on in a recharging
state (in bypass mode) and when X-Boost is disabled.
3. X-Boost is not applicable for all electrical appliances; it’s incompatible
with appliances with strict voltage requirements. Appliances with voltage
protection (such as precise instruments) are not supported. X-Boost mode is
more suitable for heating devices. Please conduct your own tests with your
devices with X-Boost enabled.
3.10 Emergency Power Supply (EPS)
The product supports EPS. When you connect the grid power to the AC Input Port
of the product through an AC Charging cable, you can power electrical devices
through the AC Output Sockets (AC power will come from the grid and not the
power station in this situation). In case of a sudden blackout, the product
can automatically switch to the battery-powered supply mode within 30ms. As a
basic UPS function, this function does not support 0ms switching. Please do
not connect the product to any device that requires 0ms UPS, such as data
servers and workstations. Please test and confirm the compatibility before
using the product. We recommend that you only charge one device at a time and
avoid using multiple ones at the same time to avoid overload protection.
EcoFlow takes no responsibility for any device failures or data losses caused
by failures to follow instructions.
FAQS
-
What battery does the product use?
It uses a high-quality lithium-ion battery. -
What devices can the product’s AC output port power?
With high-rated power and peak power, the product’s AC output port can power most household appliances. Before you use it, we recommend that you confirm the power of the appliances first and ensure the power sum of all loaded appliances is lower than the rated power. -
How long can the product charge my devices?
The charging time is shown on the product’s LCD screen, which can be used to estimate the charging time of most appliances with stable power usage. -
How can I know if the product is charging?
When it’s charging, the remaining charging time will be shown on the LCD Screen. Meanwhile, the charging indicator icon begins to rotate with the remaining battery percentage, and the input power is shown on the right of the circle. -
How to clean the product?
Please gently wipe it with a dry, soft, clean cloth or paper towel. -
How to store the product?
Before storing, please turn off the product first, and then store it in a dry, ventilated place at room temperature. Do not place it near water sources. For long-term storage, please discharge the battery to 30% and recharge it to 60% every three months to extend its battery life. -
Can I bring the product on a plane?
Troubleshooting
Indicator | Problem | Solution |
---|---|---|
OVERLOAD Icons Flash together | USB-A Overload Protection | Resume normal |
operation by removing the electrical device connected to the USB-A port.
OVERLOAD Icons Flash together| USB-C Overload Protection| Resume normal
operation by removing the electrical device connected to the USB-C port.
Icons Flash together| USB-C High Temperature Protection| After the product
cools down, it will resume normal operation automatically.
RECHARGING TIME cons Flash together| High Temperature Charge Protection|
Charging can be resumed automatically after the battery cools down.
Icons Flash together| High Temperature Discharge Protection| The power
supply can be resumed automatically after the battery cools down.
RECHARGING TIME cons Flash together| Low Temperature Charge Protection|
Charging can be resumed automatically after the battery the temperature rises
above 41°F(5 ℃ ).
Icons Flash together| Low Temperature Discharge Protection| The power
supply can be resumed automatically after the battery the temperature rises
above 10°F(-12 ℃ ).
OVERLOAD Icons Flash together| AC Output Overload Protection| Normal
operation will be resumed automatically after you remove the overloaded device
and restart the product.
Electrical appliances should be used within rated power.
(Refer to X-Boost instructions to get more details about power limitations).
Icons Flash together| AC High-Temperature Protection| Please confirm whether
the fan inlet and outlet are blocked, if not, normal operation will be resumed
automatically after the product temperature drops.
Icons Flash together| AC Low-Temperature Protection| Normal operation will
be resumed automatically after the product is used at optimum environmental
temperatures.
Icon Flashes| Fan Blockage| Please check if the fan is blocked by foreign
materials.
OVERLOAD Icons Flash together
| Car Charger Overload Protection| The product will resume normal operation
automatically after you remove the device connected to the car charger.
Icons Flash together| Car Charger High- emperature Protection| After the
product cools down, it will resume normal operation automatically.
Icon Stays On| Battery Failure| Contact EcoFlow Customer Service
If the Alarm Prompt shows on the product LCD screen during use and does not
disappear after a restart, please stop using it immediately (do not try to
charge or discharge).
If you require any other assitance, please contact EcoFlow Customer Service.
What’s In the Box
Storage & Maintenance
- Please use or store the product in an environment temperature between 68°F to 86°F (20°C to 30°C) , away from water, heat, and other metal objects.
- For long-term storage, please discharge the battery to 30% and recharge it to 60% every three months.
- For safety, please do not store the product in an environment temperature higher than 113°F (45°C) or lower than 14°F (-10°C) for a long time.
- If the remaining battery is less than 1% after you finish using the product, please recharge it to 60% before storing it. If the product is left idle for a long time with a severely low battery, irreversible damages may be caused to the battery cell and the product service life will be shortened.
- If the product has been idle for too long and the battery is severely low, it will enter a deep sleep protection mode. In such a case, please charge the product before using it again.
Fcc Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
References
- Terms of Use - EcoFlow
- EcoFlow
- EcoFlow Downloads | EcoFlow App, Manuals & More | EcoFlow US
- Privacy Policy - EcoFlow
- Terms of Use | EcoFlow
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>