BOOGIIO OK-831 1080P Full HD Car Driving Recorder User Manual

BOOGIIO OK-831 1080P Full HD Car Driving Recorder

Important notice

• This product is intended for use in motor vehicle only. Do not install the camera where it might block the driver’s view of road (including the mirrors) or the deployment of the air bags.
• Before using this camera, please insert the memory card first, and format the memory card in camera menu first.
• This camera records video at high resolution,Be sure to use high speed Micro SD card, Class 10 or above, 16GB or 32GB cards are recommended.(32G Micro SD Card Included)

The 32G Micro SD Card was already installed inside the dash cam

• This camera features Built-in battery as internal power, it’s used only for saving the video file after external power supply cuts off (car turns off). This camera will not turn on without external power supply.
• Be sure the camera lens is clean and there is noting blocking the lens.
• Do not leave the camera in direct sunlight for a long period of time or where the temperature could go above 170°F (75°C).

Interface and button function

1. Lens
2.  Speaker
3.  Micro SD Card Slot
4.  Reset
5.  MIC
6. Up Button
7.  Menu Button
8.  Down Button
9. Power Button
10. Lock Button
11. Mode Button
12. OK Button
13. Bucket
14. Mini USB Power Port

Basic Button Function

POWER

| ****

When power off, Press to turn on the camera. In any status, Press & Hold to turn on/off the camera.

---|---

OK

| ****

In Standby I Video I Photo Mode, short press to start / stop video recording / take photo.

In Setting Menu, short press to confirm selection and adjustment. In Playback, short press to start/stop playing.

Menu

| In standby, short press to Enter/ Quit Mode setting and   System setting menu.

In Playback, short Press to enter File operation Menu.

Mode| In standby, short press twice to switch mode between video I photo I

playback.

Down

| ****

In Setting Menu, short press to select option and adjust values. In Playback, short press to select media files.

Up

| ****

In Standby/ Video Recording Mode, short press to turn on / off voice recording.

In Setting Menu, Short press to select option and adjust values. In Playback, short press to select media files.

Lock| ****

In Video Mode, short press to lock the current video.

Installation Guide

1. Before installation, please check the camera’s normal function,and make sure you are using a high speed Micro SD card (speed Class 10 or above), and format the card in the camera menu before recording.

2.  Power off the camera, Use the suction cup mount to install the OK-831 dash cam on the windshield, and press down the clip on the mount. Recommended place near the rear-view mirror facing front.

3.  Adjust the angle of the camera, adjust the lens angle for best coverage, make sure you get max recording range of the road, and fasten all screws.

4.  Plug the included power adapter into the car cigarette lighter socket, hide the rest of the cable in the gap of the Interior trim board. the indicator will light up meaning power is on.
   If you only buy a front dash camera without rear camera, please ignore these 2 points below:

5.  The rear camera should be installed above the number plate, screw pad upward, connect the red power cable to the reverse lamp wire positive lead.

6. Route the camera cable to the front of the car, connect the black cable of rear camera to the main device, and connect the red cable of rear camera to the reversing lam

Operating Mode:

The OK-831 operates in 3 modes: Photo Mode, Video Recording Mode and Playback Mode. These mode also have menus to help you configure recording and taking photos, press Mode Button to access the mode you want. Watching the icon on top left corner of the screen for each mode.

Photo Taking Mode

The OK-831 camera can operate in Photo Taking Mode, and take HD photo up 12 Mega pixels.

To Take a Photo:
Simply power on the OK-831, press Mode to select Photo Mode,and press OK to take a photo. (If dash cam is recording videos,stop recording first)
Like the video recording mode, you can press the Menu once to access the setting menu for photo mode.
Press menu twice to display System Selling Menu.

1)Photo Taking Mode Interface:

1.  Photo Taking Mode Icon
2.  Exposure Value
3.  White Balance
4.  ISO
5.  Date and Time
6.  Power Status
7.  Memory Card Status
8.  Image Quality
9.  Photo Resolution
10.  Continuous Shooting
11.  Anti-Shaking

2) Menu of Photo Taking Mode:
In photo mode, press the “MENU” button to enter the setting menu of photo mode, press the “MENU” button twice to enter the system setting menu.

• Resolution: Set the photo resolution, 1.3M 1280960 / 2MHD 19201080 / 3M 20481536/ 5M 25921944 / 8M 32642448 / 10M 36482736 / 12M 4032*3024.
• Sequence: Turn On / Off.
• Quality: Defines the quality of image you capture, Fine /Normal / Economy.
• Sharpness: Defines the clarity of details in the photos,Optional:Strong / Normal / Soft.
• White Balance: Establishes the condition to capture an image based on the option given. Optional: Auto / Daylight /Cloudy / Tungsten / Fluorescent.
• ISO: Auto / 100 / 200 / 400.
• Exposure: Set the brightness sensitivity.
• Anti-Shaking: Turn ON/ OFF.
• Quick Review: Sets time duration the photo displays on screen after it has been captured.Optional: Off / 2 Seconds / 5 Seconds
• Date Stamp: Enable/Disable the date and time marks on photo.

Video Recording Mode

The camera will automatically enter Video Recording Mode and start recording when connected to a car charger and power on. A Red dot flashing on the top left corner indicates recording is in progress. Press the “OK'” button lo slop recording for the standby mode, or start recording again. (Standby mode means that there is no ongoing operations.)

Video Recording Mode Interface:

1.  Video Mode Icon
2.  Loop Recording Status
3.  Motion Detection
4.  HDR
5.  Date and Time
6.  Power Status
7.  Memory Card Status
8.  Resolution
9.  Parking Mode
10.  Recording Time
11.  G-sensor
12.  Audio
13.  Recording Status

In all 3 operating mode, you can press the MENU once to access the menu settings for the particular mode, and press twice to display System Setting Menu.
Press ▲ and ▼ to scroll through the various settings and press OK to select, press Menu again to exit the setting menu.

Video Recording Menu:
In standby mode, press the “MENU” button to enter the setting menu of video recording mode, press the “MENU” button twice to enter the system setting menu.

• Resolution: Adjust recording video resolution, 1080FHD 19201080 / 1080P 14401080 / 720P 1280*720.
• Loop Recording: This function allows you to set video file length to off/1/2/3/5 minutes, select a value to activate loop recording, so when storage fills up, it will automatically loop back to the earliest file and record over it.
• Exposure: Adjust the value to get better brightness sensitivity.
• Motion Detection: This function allows the camera to start recording when it detects movement.
• Record Audio: Turn ON/ OFF audio recording in video. Date Stamp: Enable/Disable the date and time marks in video files.
• G-sensor: Off/ Low/ Medium/ High.
• HDR: Turn ON/OFF Wide-Dynamic Range.

Playback Mode

This mode allows you to playback recording video or view photos.

1.  Stop video recording, and press Mode twice to enter Playback Mode.
2.  Use ▲ and ▼ to scroll through the recorded files/ photos, and press OK to view recorded video.

Playback Menu:
In playback mode, press the “MENU” button to enter the setting menu of playback mode, press the “MENU” button twice to enter the system setting menu .

Delete: Delete the current file displayed or delete all files.
Protect: Lock Current / Unlock Current / Lock ALL / Unlock ALL.

System Setting Menu

Press MENU twice to access System Setting Menu in any mode.The i con is highlighted in the upper left corner.

• Contact Us(Email): Scan the code to view our after-sales e-mail and contact us anytime.
• Park Mode: It’s used to protect your car after parking, with this function on, after you stop the car and the camera powers off, it will stay in standby, when camera detects shocking, it will automatically turn on and take a short video, then shut down automatically.
• Date/Time: Change the time and date by using the up and down,then press OK to confirm.
• Auto Power Off: Off / 1 Minute / 3 Minutes.
• Screen Saver: Off / 3 Minutes/ 5 Minutes/ 10 Minutes. Beep Sound: Turn On/ Off.
• Language: English/ French/ Spanish/ German/ Italian/Japanese/ available.
• Frequency: Set light frequency to 50Hz or 60Hz, and press OK.
• Format: Format the Micro SD Card.
• Default Setting: Reset all settings back to factory default. Version: Firmware version.

Specification

1.3M

Loop Recording| 1 / 2 / 3 / 5 Minutes
Power on recording| Supported
G-Sensor Lock| Supported
Language| English / French / Spanish / German / Italian / Japanese
Audio Recording| Built-in microphone, ON/ Off optional
Storage| Micro SD Card (up to 32GB)
USB Interface| Mini USB
Internal Power| Built-in Battery
External power supply| DV5V/1A
Storage temperature| -20°C- 75°C
Operating temperature| -10°C – 60°C

Features About this item

• G-Sensor lock (Gravity sensor lock)
  When the car takes collision, the G-sensor will be set off and current video clip will locked to save evidence, so it won’t be deleted in loop recording mode.
  (Sometimes you will see a lock(key) icon on screen, that is G-sensor activated)

• Screen saver (Screen protector)
  In order to guarantee safe driving, not to be effected by the light of recorder, you can set the screen saver to shut off the display, press any key to turn it back on.

• Loop recording
  In loop recording, the camera will record the video in 1/2/3/5 minutes clips, and when the card is full, the camera will cover the earliest clip with the latest one, and so forth. (Locked video will not be covered)

• Motion Detection
  Motion Detection is used to save storage space, when motion detection is on, the camera will automatically start recording when the camera detects movement is stopped.
  We do not recommend turning on this function during driving for your safety.

Customer Questions & Answers

Q :Keeping Saying SD Card Full?

1.  Format your new SD card on the dash cam when first use.We suggest using class 10 high speed micro SD card, no more than 32 GB.（Please remember insert SD card before dash cam power on!）
2.  Please check if you set loop recording success, if set success, there will have a mark on dash cam screen.
3.  Please do remember to close parking monitoring and motion detection function when you’re driving on the road.(if not,these two functions trigger the captured locked videos which can’t be overwrite. If it shows card full,you need to format the card.)
4. If the G-sensor is set to high, it is easy to lock file and make the Micro SD card full,so suggested set to low, safe enough and recommended to format your SD Card monthly.
5.  If keep saying ” insert C6 and above SD card”, it may because the SD card is not compatible to dash cam. Some SD card on the market is false SD card. Please try a new SD card.

Q : The camera can not record video or take photos?
A : Be sure you are using suitable memory card: Speed over Class 10, Capacity no less than 8GB. Be sure the memory card is formatted properly and inserted correctly.

Q : The camera automatically stop recording?
A : Format the memory card in setting menu The G-sensor might be triggered too often and locks too many video files, try low sensitivity and turn off motion detection function when you are driving.

Q : The camera can not turn on?
A : This camera features Built-in battery as internal power, it’s used only for saving the video file after external power supply cuts off (car turn off). This camera will not turn on without external power supply. Check the power supply, make sure they are connected properly,power indicator on the power adapter is on, and the connectors are tight.

Q : Suction mount cannot attach on windshield well?
A : Please clean the windshield with a glass cleaning wipe.
Removed the protective film. Please soak suction mount to warm water for a moment. If it is still not working, please contact us at [email protected] to get a replacement.

Q : The recorded video is unclear?
A : Make sure there are no fingerprints or dirt on the lens, try to adjust the angle to avoid blocks or glare or wind-shield reflecting.

Q: Color of the video or photo is not good?
A : Verify that Frequency option is set to 50Hz or set accordingly.

Q : The camera crashes or not responding to operations?
A : Use a pin or and unfolded paper clip, press the RESET button to restart the camera.

After-sales Service [email protected]   

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>