Maxxprime WN7028 Adjustable Bed Base Owner’s Manual
- June 5, 2024
- Maxxprime
Table of Contents
Individual Head-Tilt
Adjustable BED BASE
#WN7028 OKIN Motor
– 3 Individual Motors for Head-Tilt, Back Incline & foot Incline
– Dual Massage / USB Ports / Bluetooth / UnderBed Lighting
– Free APP for Bluetooth Smart Device Controlling ( IOS & Android )
4 Massage for QUEEN SIZE
2 Massage for Twin XL Size
Owner’s Manual
CONTENTS
Advisory
Setup and Installation
Wireless Hand control
ADVISORY
Attention: Read the following information before using this product . Failure to use a surge protection device could compromise safety or cause product malfunction could void the electrical portion of your warranty.
– Electrical surges are by far the biggest cause of problems with electrical circuits. In order to help protect your investment in case of a power surge or outage, use an electrical surge protection device (not included).
WARRANTY WARNING!
Do not open or tamper with the transformer, control box, motors, or remote
control (with the exception of battery compartments). The product warranty
will be void if these components are tampered with.
SMALL CHILDREN AND PETS:
Immediately dispose of all packing materials as it can smother small children
and pets. Do not allow any person or pets under the bed. Children,
convalescents and disabled person should not operate the bed without adult
supervision.
HOSPITAL OR CONVALESCENT USE DISCLAIMER:
Adjustable beds are designed and engineered for a life style of in-home
comfort and are not intended for hospital use or for a bed-ridden patient on
an extended recovery. Adjustable beds are not equipped with bars to help
patients get safely in and out of bed and are not intended to be used around
tent type oxygen therapy or explosive gases.
PACEMAKER WARNING:
The massagers in this bed produce mechanical vibrations that may activate a
special sensor in your pacemaker that detects motion. This can fool the
pacemaker into “thinking” you are engaged in some sort of physical activity
and require a faster heart rate and you may experience a sensation similar to
when you are exercising. Consult your physician for further information.
PRODUCT RATINGS:
PRODUCT RATINGS: The product’s lift motors are not designed for continuous use
of more than 2 minutes in an 18 minute period, or approximately 10% duty
cycle. For every 30 minutes the massage motor is used, the massage motor needs
30 minutes of rest. The massage function should be used for a maximum of 2
hours in a 12 hour period. Any attempt to circumvent or exceed this rating
will shorten the life expectancy of the product and may void the warranty.
WEIGHT UNITS:
The limitation for this adjustable bed is 750 lbs. The bed will structurally
support these weights, provided it is evenly distributed across the head and
foot sections. This product is not designed to support or lift this amount in
the head or foot section alone. Exceeding this weight restriction could damage
the bed and/or cause injury and void the warranty. Enter or exit the bed in a
flat position and do not sit on the head or foot sections while in the raised
position.
LIFTING AND LOWERING MECHANISMS AND MASSAGE UNITS:
It is normal for the raising and lowering feature on this bed will emit a
minimal humming sound during operation. The massage feature creates a
vibrating hum during operation and the resonance will increase accordingly
with a higher intensity motor setting.
LOCATION ENVIRONMENT:
The level of sound experienced in a room is directly related to the
environment within that location. In a room with hardwood floors and the
massagers turned on, a vibrating noise can be noticeable. To reduce the
resonance, place a piece of carpet or rubber casters cups under the legs. The
rubber caster cups also prevent the bed sliding when located on smooth or hard
surface flooring.
TO REDUCE THE RISK OF SHOCK, BURNS, FIRE OR INJURY:
Make sure the base is in a flat position, the vibrating motors are off before
unplug from power source. Always unplug the base from the electrical outlet
before cleaning or servicing the base. If the cord or plug is damaged,
discontinue use of the bed base and contact qualified service personnel for
examination and repair.
FCC COMPLIANCE:
This device complies with part 15 of the FCC Rules for residential use.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Radio Frequency: 2.4 GHz
EMERGENCY BATTERY BACKUP:
In the event that the base is stuck in an articulated position during a power
outage-the battery backup in the transformer will return the base to flat
position. Batteries are not to be used for normal operation of the base.
Install two 9 volt alkaline batteries into the battery backing transformer.
Use the PAIR button on the control box to return the base to flat
position.
SETUP & INSTALLATION
Important: We strongly recommend
Two able-bodied adults setup and assemble this product.
Step 1:
Check and verify all parts are included before discarding any packing
materials.
All electronics and components that need to be installed are located in boxes
under the base or attached to the frame.
A)
| B)| C)
| D)
---|---|---|---
E)
| F)
| G)
| H)
A) Wireless Remote Control (1)
B) Mattress Retainer Bar (1)
C) 4″ Legs 4″ +6″(6)
D) Power Cord AC (1)
E) Transformer with emergency battery backup (1)
F) Control Box (1)
G) Power Cord DC (1)
H) SYNC Cord (1) (only for TXL bed)
Step 2:
With the help of your able-bodied assistant, place carton on floor with arrows
point downwards.
Step 3:
Connect the Transformer “E” to Control Box “F” with Cord “G” : The Control Box
is the Black Box attached to the bottom of the bed . Plug one side of Power
Cord DC “G” into the Control Box “F” and Plug another side of “G” into
Transformer “E” . Extend the Power Cord AC “D” and plug it into the
Transformer “E”. Connect the Plug to 110V Power socket.
Step 4:
– Unplug the Power Cord.
– Install the six legs firmly into the base of the frame.
The six legs screw into the threaded holes in each corner of the adjustable
base frame. (See Figure 2).
The legs are stackable. The combination give you a set of six 4″,6″or 10″legs.
– Note: The minimum leg height:4″, The warranty is void if the minimum leg
height is not used.
– Do not over tighten.
Step 5:
With the help of your able-bodied assistant , carefully lift the adjustable
bed frame and set it in place upright on its legs. Excessive pressure may
damage the legs. Remove all protective plastic covering. Note: check and make
sure that all power cords clear and do not interfere with any Adjustable Bed
Mechanisms; Dispose of covering property to avoid injury.
Step 6:
Note : The Mattress Retaining Bar is mounted upside down for shipping only.
Remove the Mattress Retaining Bar in the foot section of the bed bottom and
turn the bar upright and reinstall by carefully aligning and pushing the bar
into place. (See Figures 3 & 4. )The retaining bar is to prevent the mattress
from slipping out the base and should not be used as a handle of the base.
Using as a handle will damaged the retaining bar holders. Screws come out from
the retainer bar holders will be considered as a damaged part and not a
defective part and is not covered by the warranty.
figure 3 & 4
Step 7:
Scan QR Code to download Free Bluetooth APP “OKIN ComfortBed II”.
( IOS & Android )
( Android ) ( IOS version 8.0 and above)
How to pair the bed to APP:
Please open BLUETOOTH on your phone settings, then open the “OKIN ComfortBed
II” app and follow below steps:
Step1: CHOOSE “3M” Step2: TOUCH “H” Step3: Click “Setting”
Step4: Select the device named “OKIN-xxxxxxx” the APP will be connected and says “connect success!”
APP Functions
ATTENTION
The remote control has already been synchronized and preset during
production.
Please skip Step 8 unless the remote does not work.
Step 8:
Synchronize the remote with the control box.
First find the black box mounted under the bed. Double-click the black PAIR
button , the Indicator Light of the control box change to blue and the
under bed light flashes, At this time, it enters the pairing state. Then press
the PAIR button on remote control , the back light of the remote control
flashes, At this time, the remote enters the pairing state. until the back
Light on remote control stop flashing and constant, the Indicator Light of
the control box changes from blue to green and constant or the under bed light
stop flashing and turn off (See Figure 5).
The adjustable bed should be working after matching the remote with the
control box. Press the Head Up button , Foot Up button , and Flat Button to
test.
USING SAME REMOTE
The bed base is designed to allow two Twin X-Long bases to become an Split- King base. Owner can use the same remote to control two side-by-side beds bases by Connecting the two control boxes with the SYNC cord (H). Plug one side of the cable into the “SYNC” on the side of the control box and plug another side into the “SYNC” on the side of another control box , then you can connect two control boxes(See figure 6&7) .
It is important that the two control boxes expected to work synchronously must be still configured differently to pair with the different remote control with different DIP-Switch position. Do not pair both control boxes with the same remote control , Each remote must have a different DIP-switch setting.
The synchronise cord is not on the full warranty list. We will replace it for free if it is defective.
Setup is now complete. Enjoy.
Wireless Remote
#WN7028 Adjustable Bed Base with OKIN Motor
Memory Button ZG, ANTI- SNORE, TV, LOUNGE.
Press once to raise to Preset position.
1 Timer Button
– Use to set the desired time, Select 10-20-30 MIN first and then turn the
HEAD/FOOT massage button on.
2 Massage ON/OFF
Use to turn ON/OFF HEAD/FOOT massage
3 Head Massage Button
– Turn the head massage on and off.
– Adjust massage intensity for the head.
4 Pillow Tilt Raise/Down Buttons
Use to raise or lower the Pillow tilt of the bed
5 Head Down Button
Used to lower the head of the bed base
6 Head Up Button
Used to raise the head of the bed base
7 PAIR Button
Use to Synchronize the remote control with the control box.
8 Preset Position Button ZG, ANTI- SNORE, TV, LOUNGE.
- Press the “FLAT” button to return the bed to flat position.
- Adjust the head and foot to desired positions.
- Press and continue holding in the “ZG” abutton for around 5 seconds until until timer LED flashes confirm the successful setting.
- You can reset the 4 position button by repeating the above steps.
9 Children Safety Lock and Unlock Buttons
Press and hold child lock button, the red backlight of this button flashes,
after press for 5s, the red backlight stop flashing, the remote enters locking
mode. Press the child lock button for 5s, the red backlight flashing until
off, remote enters unlocking mode.
10 Foot Up Button
Used to raise the foot of the bed base
11 Flat Button
Press to return to flat position
12 Foot Down Button
Used to lower the foot of the bed base
13 Foot Massage Button
– Turn the foot massage on/off.
– Adjust massage intensity for the foot.
14 Massage Type Button
Offer 3 massage actions: Pulse, Wave & Constant
15 Under Light Button
Use to turn on and off the under light
0-30 DEGREES
Individual Head/Pillow Tilt
0-60 DEGREES **0-45 DEGREES
** Individual Back Incline Individual Foot Incline
Free Adjustment Pillow Tilt
independent MOTOR for Pillow TILT
WHEN TWO BEDS DO NOT ALIGN:
on the higher angled bed of the two, use a 19mm wrench to trun the nuts on the
new “LEVEL RIGHT” counterclockwise to adjust the angle until the higher angle
bed match the level of the lower angle bed and lock the nut with the reinforce
nuts. The two beds are now aligned. (For Twin XL and SPLIT King)
Dear Valued Customer,
Thank you so much for your order, we sincerely hope that you would be satisfied with our product and service.
Your satisfaction will be a great motivation for us. We would do our best to offer you a pleasure shopping experience on Amazon, if you have any concern about our product and service, please do not hesitate to contact us via support@maxxprime.com
We are looking forward to hearing from you in the near future and also we expect have a long term corporation with you.
Yours sincerely,
Thank you,
Maxxprime Customer Support
E-mail: support@maxxprime.com