enabot ebo Pro Smart Robot 1080P Camera User Manual
- June 5, 2024
- enabot
Table of Contents
Smart Robot 1080P Camera
User Manual
Meet Ebo
-
Interchangeable Hat
-
Feather/Accessory Insertion Socket
-
Laser Pointer
-
Camera
-
Charging Stand
-
Smart Collar (Sold Separately)
-
Download the Ebo App
Scan the QR code, download the Ebo App, and complete registration. http://downloads.enabot.com
Ebo requires the Ebo App in order to be used. -
Place the Charging Stand
Place the charging stand in an open space and plug it into a power source. Please try to keep the charging stand 1.2m away from obstacles. -
Initialize Ebo
Place Ebo on the charging stand for initialization. -
Network Configuration
Follow the instructions on the Ebo App and generate your own QR code. Scan the QR code with Ebo’s camera.
Compatible with
both 2.4G and 5.8G WIFI networks.
Your Ebo and smartphone must be connected to the same WIFI for pairing -
Network Connected
Congratulations! Your Ebo is connected to the Internet when ” **** ” is displayed in Ebo’s eyes.
-
Enjoy your Ebo!
Control Ebo with your smartphone. 
The Ebo App
- About
- Ebo Cards
- Click to Connect to Ebo
- Ebo News
- Add Your Ebo Cards
- Smart Video Editor
- More Functions (Settings/Change WIFI/Auto Play/Add Collar/About Ebo)
The User Interface
- only available when Ebo’s hat is integrated with a laser pointer.
- Steering Wheel
- Move Forward
- Move Backward
- Laser On/Off
- Circle
- Battery
- Settings
- Photo
- Video
- Mic On/Off
- Speaker On/Off
- Al Tracking and Capturing
Charge
Place Ebo in the position shown in the diagram. Make sure the connector pins on the bottom of your Ebo are in contact with the connector pins on the base of the charging stand.
Check Charging Status
The light indicator is red while charging. The light indicator is green when
your Ebo and Smart Collar are fully charged. 
Restart/Turn Off/Factory Reset
Restart: Press the Reset button. Turn Off: Press the Reset button twice.
Factory Reset: Press and hold the Reset button for 5 seconds. 
Change “Hat”
Take off the hat by gently pressing down on the hat and turning it counter-
clockwise. Put on the hat by gently pressing the hat on Ebo’s head and turning
it clockwise. 
Hat
The soldier hat is integrated with a laser pointer. The soldier hat and the
bamboo hat have sockets for feathers or accessories (silicon feathers are
included in the pack). 
FCC Regulatory Compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user s authority to operate the
equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter. This equipment should be
installed and operated with a minimum distance of 20cm between the radiator
and your body.
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier Trade Name: 2AUR8, Model No.: EBO CARPAL PRO
Responsible Party – U.S. Contact Information
Sclera Digital, Inc.
11815 Laurelwood Dr. Unit 1, Studio City, CA 91604
(818)826-3128
Feather
BE AWARE: The feathers could pose an unknown risk to pets if swallowed.
For more information, please visit our YouTube channel and website.
|
---|---
https://www.youtube.com/c/eboebo4pet| https://enabot.com/p/Support
E-Hub, Qianhai, Shenzhen, Guangdong, P.R.C.
Designed by Enabot, Made in China.
All rights reserved.
www.enabot.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>