KAR-TECH MCT245 Mini Wireless Receiver User Manual
- June 5, 2024
- KAR-TECH
Table of Contents
MCT245
2.4GHz RECEIVER
OEM INSTALLATION AND OPERATION MANUAL
June 27, 2020 **TH
MCT245 RECEIVER**
DESCRIPTION
The MCT245 is a frequency hopping spread spectrum transceiver unit, designed to be compatible with US (FCC Part 15.247), Canadian (RSS-210), EU(EN 60950-1, EN 300 328, EN 301 489), and Australian() regulations for license free use in the 2.4 GHz ISM band. The MCT245 is designed for mobile applications in accordance to Part 2.1091(b). The MCT245 remote control products are assembled by KarTech, at Kar-Tech. There are no user-serviceable parts on the MCT245 transceiver. The MCT245 is not designed for multiple antenna applications and should not be used to transmit simultaneously with any other transmitter.
OPERATION
The MCT245 is a radio Receiver product for the 2.4 GHz ISM bands. The Receiver
microcontroller includes a CPU, GPI/O, a fully integrated frequency
synthesizer, a power amplifier, a modulator, and a receiver unit. The data
received from the antenna is sent to the microcontroller for processing. The
MCT245 microcontroller monitors the input data, and received data, and
controls outputs. The system data is sent to the RF processor and then to RF
circuit, and then to the antenna. The microcontroller is responsible for the
control of the entire communication. The MCT245 transceiver contains a DC
regulator which generates a constant 1.8 VDC for the digital circuitry. The RF
section runs on
the 3.3V supply.
The MCT245 uses Frequency Hopping Spread Spectrum that uses 16 channels for
any hop mode, between 2.407GHZ and 2.470GHZ, with 1MHZ resolution. The
receivers are matched to the transmitters to use the same channels and
sequence as the transmitter’s signals.
The MCT245 controls outputs which can operate relays, hydraulic valves,
lights, or other similar load devices, according to customer requirements.
Where Used
Typical applications for the MCT245 are to control valves, relays and lights
on agricultural equipment, construction equipment, and other similar
equipment.
INSTALLATION
- Attach the external harness to the MCT245.
- Assemble the MCT245 assembly into the Enclosure.
- Place a label on the outside of the enclosure on the side. On the label, include the following: “FCC ID: P4U- MCT245” and “IC:4534A- MCT245, CE”
Application Requirements:
A) Power the MCT245 Receiver with 9-30VDC nominal voltage, with peak current
draw of 150mA.
B) Assemble the MCT245, into a KAR-TECH Receiver enclosure.
C) The MCT245 is to be installed only in mobile applications. See Part 2.1091
for definitions of mobile and fixed applications.
D) Do not operate the MCT245 without an antenna.
E) Documentations: In the host’s User Manual include the following:
a. That there are no user-serviceable parts in the radio product. They should
not remove or install radio modules.
b. The “Instructions To The User” section.
c. The “Industry Canada Statement”.
d. Include in the manual, “This device is granted for use in Mobile only
configurations in which the antennas used for this transmitter must be
installed to provide a separation distance of at least 20cm from all personal
and not be colocated with any other transmitters except in accordance with FCC
and Industry Canada multi-transmitter product procedures.”
BEFORE APPLYING POWER!
- Check power and ground for proper polarity.
- Read the rest of this manual.
TROUBLESHOOTING
There are no user-serviceable parts in the MCT245 Receiver. Contact your KAR-
TECH representative for further instructions or servicing.
PARTS LIST
| PART NUMBE | DESCRIPTION |
|---|---|
| 022081A | MCT245 RADIO TRANSCEIVER – REMOVEABLE ANTENNA |
There are no user-serviceable parts inside the transmitter or the receiver.
Return the units for service.
The information, specifications, and illustrations in this manual are those in
effect at the time of printing. We reserve the right to change specifications
or design at any time without notice.
SPECIFICATIONS
Equipment Class ………………………… Part 15 Spread Spectrum Transmitter
FCC ID ………………………………………………………………….. P4U- MCT245
ICC (Industry Canada Certification) ID ………………………… 4534A- MCT245
TRANSCEIVER
Power supply ………………………………………………………………. 9-30VDC
Operating Current ……………………………………………………………… 48mA
Operating temperature – Radio ………………………………… -40˚C to +85˚C
Storage temperature …………………………………………… -40˚C to +100˚C
RF Frequency ………………………………………………………….. 2.4-2.48 GHz
RF Transmit power (EIRP) …………………………………………………. 100 mW
RF Receive Sensitivity ……………………………………………………. -126 dBm
INSTRUCTION TO THE USER
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The product can be installed or integrated in mobile or fix devices only. This
product cannot be installed in any portable device, for example, USB dongle
like transmitters is forbidden. This product complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
This product must be installed and operated with a minimum distance of 20 cm
between the radiator and user body.
If the FCC identification number is not visible when the product is installed
inside another device, then the outside of the device into which the product
is installed must also display a label referring to the enclosed product. This
exterior label can use wording such as the following: “Contains Transmitter
product FCC ID: P4U-MCT245”
When the product is installed inside another device, the user manual of this
device must contain below warning statements;
-
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product
INDUSTRY CANADA STATEMENTS
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
OEM Responsibilities to comply with FCC and Industry Canada Regulations
Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
IC Radiation Exposure Statement
The product can be installed or integrated in mobile or fix devices only.
This product cannot be installed in any portable device, for example, USB
dongle-like transmitters is forbidden.
This product complies with IC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
This product must be installed and operated with a minimum distance of 20 cm
between the radiator and user body.
If the IC number is not visible when the product is installed inside another
device, then the outside of the device into which the product is installed
must also display a label referring to the enclosed product. This exterior
label can use wording such as the following: “Contains IC: 4534A- MCT245”
MCT245 RECEIVER
When the product is installed inside another device, the user manual of this
device must contain the below warning statements:
1. This device complies with Industry Canada’s license-exempt RSS. Operation
is subject to the following two conditions:
(1) This device may not cause interference; and (2) This device must accept
any interference, including interference that may cause undesired operation of
the device.
The devices must be installed and used in strict accordance with the
manufacturer’s instructions as described in the user documentation that comes
with the product.
EUROPE
CE NOTICE
This device has been tested and certified for use in the European Union. See
the Declaration of Conformity (DOC) for specifics.
If this device is used in a product, the OEM has the responsibility to verify
compliance of the final product to the EU standards. A declaration of
Conformity must be issued and kept on file as described in the Radio and
Telecommunications Terminal Equipment (R&TTE) Directive.
The ‘CE’ mark must be placed on the OEM product per the labeling requirements
on the Directive.
Declaration of Conformity (DOC)
This DOC can be downloaded from www.kar-tech.com.
The device complies with RF specifications when the device used at your body.
Caution: Must use the original antenna. Other antennas are not allowed to be
used.
The device according to the regulation in Directive 1999/5/EC and complies
with standards as follow:
EMC (Article 3.1b)| ETSI EN 301 489-1 V 1.9.2| Report No.:
CTL1512313913-WE
---|---|---
ETSI EN 301 489-17 V2.2.1 (2012-09)
Radio (Article 3.2)| ETSI EN 300 328 V1.8.1| Report No.:
CTL1512313913-WR
Safety (Article 3.1a)| EN 60950-1:2006+A11:2009+A1:2010+Al2:2011+A2:2013|
Report No.: CTL1512313913-WS
Health (Article 3.1a)| EN 62479: 2010| Report No.: CTL1512313913-WH
| [Titles, dates of publication of documents mentioned ]|
Documents / Resources
| KAR-
TECH MCT245 Mini Wireless
Receiver
[pdf] User Manual
MCT245, P4U-MCT245, P4UMCT245, MCT245 Mini Wireless Receiver, Mini Wireless
Receiver, Wireless Receiver, Receiver
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>