Fujian Baldr Technology ITV0103W Wi-Fi Irrigation Water Controller System User Manual
- June 5, 2024
- Fujian Baldr Technology
Table of Contents
Fujian Baldr Technology ITV0103W Wi-Fi Irrigation Water Controller System
Manual
- Production Overview
- Product Appearance
- Website and QR Code
- Main Functions
- Illustrated Operating Instructions
- Connection and Basic Information
- Manual Operation
- Plans and Setting
- Sensor Connection
- Tap-to-Run & Automation Irrigation
- Tips
- Warranty & Warning
- Basic Parameters of the device
Production Overview
Downloading the App
Rainpoint
Main Function
- This kit includes one WiFi water timer and one WiFi gateway
- One gateway can pair with maximum 4 WiFi water timers
- 433mHz RF communication with WiFi gateway and Water Timer
- The WiFi gateway may also be used as WiFi timer socket
- Set and check irrigation schedule through smart phone APP, connecting with Wi-Fi
- Available to work with soil moisture sensor
- One Wi-Fi timer can pair one gateway and one Wi-Fi gateway can pair one soil moisture sensor
- Delay the irrigation schedule base on the data from soil sensor Manually ON/OFF the water timer
- Water flow meter function
- With Irrigation mode and Mist mode options for watering
- Low power indicator
- With built-in filter
- Water-leakage alert
Up to 60 meters depending obstacles between gateway and tap timer Illustrated Operating Instructions
- Connection and Basic Information
Register an account on the RainPoint App before connecting to WIFI smart water timer.
Press the button to add a device.
Plug your WiFi gateway into an electrical socket. Open the APP and click the
“+” on the right top corner to add devices. Click the
“Irrigation Hub” and enter the WiFi password. Hold the button until the blue
LED light rapidly blink which means the device is ready for connection.
After the gateway getting connected, click “Manager added devices” to add WiFi water timers.
Insert 4xAA batteries to the water timer and press and hold the button until
the white LED light rapidly blink which means the device is ready for
connection. Select the choice of Wi-Fi water timer and wait for connection. It
will show “Device added successfully” once WiFi water timer connects
successfully.
Note: If it do not get paired in 20s, the LED indicator will light off
and stop connection.
Please press and hold the button for a few seconds again until the LED
indicator flashes rapidly to start connection.
If the LED indicator does not flash rapidly, please remove and reinstall the
batteries, then press and hold the button for 5 seconds.
Note：
If the water timer already paired with one gateway before, once it has been
re-insert batteries, the LED light will slowly blink, it means the device is
searching the gateway automatically.
After finishing the connection, all the paired devices will be displayed on
the page. The “Wi-Fi Socket” can set the gateway socket’s power ON or
OFF.Click the WiFi Water Timer and get into the main page of the device.
The following information will be shown on the page: Temperature unit
selection, Last water usage, Soil Moisture and Temperature (if already
connected the sensor), Battery status, Mode and Next irrigation time. The
background color will turn red if the moisture of soil is higher than setting.
At the bottom, there is an operating panel with several options: Parameter, Irrigation control, Plan, Sensor and My.
After clicking the right top button, there is a basic information and operation board with several different options: Device information, Tap-to-Run and Automation and other basic functions and services for the device.
Shared the device and setting to your home member who has added on the family group.
There are some existing Q&A to solve problems. Tip: Please e-mail our customer service or call us by phone to get support if you need more help.
Manual Operation
Manual mode: Click the “Irrigation control” to manually turn ON/OFF the
water timer and set the start time.
Tips: The connection delay will be around 0.5 to 1 seconds, please do not
repeatedly press the button.
Plans and Setting
Schedule overview
On the Schedule page, there are Daily notices of a week, Plan detail display
board and rain delay selections.
There are three plans that can be set in total. Each plan has a unique
represent color, which will be shown under the day mark as a point after
turned on.
The setting detail of each plan is shown under as a row and the on/off button
is on the right side.
The Rain delay (Watering Delay) can set with 24H, 48H and 72H.
Plan Setting
Click the Plan A/B/C to set daily irrigation schedule and rain delay plan. The Irrigation schedule includes two mode: Irrigation mode and Mist Mode. Different mode have different setting options and both of them can be set with 12-hour or 24-hour.
The figure shows that irrigation mode watering 20 minutes. Start time is 10 AM every Tuesday, Wednesday and Thursday .
The figure shows: mist mode spray 30 seconds of every 5 minutes, duration time is 4 hours (starting from 10:00 am and stop at 3:00 pm).
Sensor (Not including)
Sensors can be connected to monitor the soil moisture and temperature, and then the data will be displayed as a graph. When the soil moisture goes high, the water timer will stop watering automatically once customer set the “stop watering moisture level”.
The water timer has its own water flow monitoring function and users can check the daily water consumption and last water usage. (The minimum monitoring water flow is 25L/H).
Tap-to-Run & Automation Irrigation
The Tap-to-Run and Automation planning systems are at “Smart” selection which in the middle of the bottom panel.
Click the plus sign at the right top corner and schedule a smart plan. There are some options to set up: Condition, Task and other personal options.
There are many options shown on the page to select and a variety of conditions can be added at the same time. In the device condition, the basic options of the connecting devices are related to the data from the WIFI timer and sensors.
The plan will be triggered when any single condition is met or all conditions are met at the same time. All the data of current conditions is automatically searched online by the App.
Different task could be set: Tap to Run, Enable or Disable Automation, Send Notification, Delay and Device Option. When the conditions are triggered, the task will be executed.
After finishing setting, icons will be found under Tap-to-Run and Automation. The button on the right can enable or disenable the Automation plan. The Tap- to-Run function connects different plans and devices at the same time to enable “One-Click Management”.
Tips and Warnings
Please make sure the smart phone is near the Wi-Fi water timer when connecting or setting the watering plan. The best range for operation or connection is within 60 meters in the open area.
The watering timer will follow and perform the preset watering schedule after application set successfully, even if the phone is out off the best Connecting range.
LED light meaning:
- White and rapidly blink: ready for pairing to smart phone;
- White and slowly flash: searching the connecting gateway;
- Red and blink every 6 seconds: low batteries power warning;
- Red and breathing light blink: water leaking when turn off the water timer;
- Red when searching a sensor: does not find the sensor.
Warranty & Warning
WARRANTY
The warranty aims for the problem of non-artificial damage and provides a one-
year warranty from the date of leaving the factory.
WARNING
- Under freezing temperatures, timers should be removed from the faucet and stored indoors to avoid potential freezing damage.
- Please clean filters regularly and replace if it is worn in order to prolong life of timer.
Basic Parameter of the device
TECHNICAL PARAMETER
- 1″BSP or 3/4″ NH inlet
- 3/4’’outlet thread
- Working pressure: 0.5 bar to 8 bar(10PSI-120PSI)
- Max flow: 5L/min to 35L/min
- Water proof: IP54
- Working temperature: 0℃ to 50℃(37°F-122°F)
- Battery life: over one year
- WIFI timer power by 4 AA batteries, WIFI gateway power by AC power
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that my cause undesired operation.
MODIFICATION: Any changes or modifications not expressly approved by the
grantee of this device could void the user’s authority to operate the device.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment should be installed and operated with minimum distance 20cm
between the radiator& your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>