RACOS L-RA1 BLE Communication Automatic Door Control Device User Manual

RACOS L-RA1 BLE Communication Automatic Door Control Device

Features

O LG robot and BLE communication interface are connected to control automatic door opening and door closing. Hereinafter, Mac Address setting and BLE output(dBm) adjustment through a separate dip switch setting. Each control state can be checked through the LED. Relay output state value can select no power/DC12V. (Using jumper pins)

Applications
LG Electronics guide robot

Description

It is a BLE communication automatic door control device that is linked to LG Electronics’ guide robot. The power connection and relay output terminal of the device are connected to Molex(5267-05P), and when the power supply and automatic door contact control lines are connected, the control is ready. Afterwards, control is performed through a BLE communication connection with LG Electronics’ guide robot (control through a separate communication protocol).

The main functions are as follows

• Automatic door control through LG Electronics’ guide robot and BLE communication connection (door open, door closed)

Product information

In-box

Accessories

| SSWH5264ASY-5P (Molex 5267-05S For connection),

Screw, Screw support

Environmental Conditions

Operating Condition

| ****

Temperature

| Relay| -20℃ ~ 50℃
Main MCU| -20℃ ~ 50℃
BLE MCU| -20℃ ~ 50℃
Humidity|  | 85% RH MAX
Storage Condition| ****

Temperature

| Relay| -40℃ ~ 70℃
Main MCU| -40℃ ~ 85℃
BLE MCU| -40℃ ~ 125℃
Humidity|  | 85% RH MAX
Posture| Shaft Horizontal Only

Note: No Dew Condensation

Product Composition

Main PCB

| Power| DC 12V

Use

| Transmitting and receiving data from BLE Module, Relay Control

BLE Module

| Power| DC 3.3V

Use

| Transmitting and receiving data from Main PCB, Connect to BLE

Device

Circuit contents

Constant voltage

circuit

| AP1509-50S(12V->5V), LM1117-3.3(5V->3.3V)
Relay circuit| DS1E-M-DC5V (2 Ch, A&B Contact point)
LED circuit| LED for status display

When power is applied for the first time, all LEDs are lit up. Red LED lights when detecting a switch change. Blue LED lights up when receiving the BLE signal.

White LED lights during relay operation.

Switch circuit| SW1: Address setting switch (MAC)

SW2: Output setting switch (BLE TX dBm)

Electrical specification

In/Out (CN1, Molex 5267-05S)

When the locking device requests DC12V input, the jumper pin can be connected to supply DC12V.

Federal Communications Commission(FCC)

Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment and For indoor use only, use outdoors or in other modes not covered by this manual may violate the FCC regulation and violate the user authority to use the product.

FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance.
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Responsible Party – U.S. Contact Information
LG ELECTRONICS U.S.A, INC.
Street Address: 111 SYLVAN AVENUE, NORTH BUILDING
ENGLEWOOD CLIFFS, N.J. 07632
City, State: U.S.A
Telephone number or internet contact information

• Name : Kyung-Su Han
• Telephone number : 1-201-266-2215
• Internet contact information : kyungsu.han@lge.com

Industry Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

IC Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
www.racosys.com 

References

• RACOS SYSTEM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>