GENESIS IRID 503 ARGB LIGHTS Installation Guide
- June 5, 2024
- Genesis
Table of Contents
GENESIS IRID 503 ARGB LIGHTS
HOW TO INTSALL
FAN INSTALLATION
-
Remove front panel by gently pulling bottom part. Unscrew side panel.
-
Install fans accordingly using screws and according to case plan.
-
Suggested fan airflow orientation.
2,5” SSD INSTALLATION ON MOTHERBOARD TRAY -
Put AV1 pads onto SS1 screws.
-
Next gently screw-in the screws (x4) with applied pads into SSD bottom screw holes.
-
Fix SSD into designated SSD tray holes.
Important note: Too tight screwing-in screws with applied pads might cause drive fastening in designated holes impossible (pads will get squeezed). Too lose might cause drive to fall off during transport.
2,5” SSD DRIVE INSTALLATION ON 3,5” HDD CAGE -
Remove HDD cage (pull out).
-
Screw-in SSD on top of HDD cage using MB1 (x4) screws into SSD bottom holes.
-
Install HDD cage (slot-in) with secured drive back into case.
3,5” HDD DRIVE INSTALLATION -
Remove HDD cage (pull out).
-
As first screw-in HDD drive on top of HDD cage using HD1 (x4) screws into HDD bottom screw holes.
-
Second screw-in HDD drive inside HDD cage using HD1 (x4) screws into HDD side screw holes.
FRONT PANEL O/I PORTS INSTALLATION -
Connect front panel I/O connectors to motherboard according to motherboard manual.
FAN CONTROLLER INSTALLATION -
Plug-in SATA power connector from PSU to controller SATA socket. Backlight mode control via button on front I/O case panel.
USER MANUAL – ARGB FAN CONTROLLER
NOTE: controller is pre-installed and ready to use right after connecting
to power source.
CONTROLLER DESCRIPTION
-
LED1 … LED6 – ARGB backlight headers for fans. To get the right backlight effect, connect the fans one by one. ARGB 3-PIN 5V
type header. -
SW – To the header can be plugged cable from the front panel of the case – „RESET” or „LED SW” (depends on the model) –
terminated with a 2-pin connector. By default cable is pre-installed. RESET/LED button on case allows then to change backlight
mode, turn mode off or switch to motherboard control of fans backlight. -
DATA (or PC PWM DATA depends on the model) – header with pre-installed cable which ends with following connectors:
-
PWM – Connector can be plugged into designated 4-PIN PWM header on motherboard (it must be confirmed in motherboard
user manual, if 4-PIN header provides PWM signal or DC). It allows fan speed control from BIOS. If controller is not connected to
motherboard, fans run at default RPM. This PWM connector have 2 pins in fact, which is intended and correct. -
ARGB – 3-PIN 5V connector. After plugging into ARGB header on motherboard (check in motherboard user manual for header
location and specification), allows fan backlight control from BIOS / motherboard software.
OPTIONAL:
-
VDG – Gigabyte ARGB 3-pin backlight connector, only compatible with specific manufacturer’s motherboard models.
- FAN1 … FAN6 – 3-PIN fans power connectors.
- LED7, LED8 – LED strip 3-PIN ARGB connectors.
- POWER – SATA power connector.
EU Declaration of Conformity – Hereby, IMPAKT S.A. declares that that the equipment type NPC-1559 is in compliance with Directives 2014/30/EU and 2011/65/UE. The full text of the EU declaration of conformity is available via the product tab at www.impakt.com.pl
The WEEE symbol (the crossed-out wheeled bin) using indicates that this product in not home waste. Appropriate waste management aids in avoiding consequences which are harmful for people and environment and result from dangerous materials used in the device, as well as improper storage and processing. Segregated household waste collection aids recycle materials and components of which the device was made. In order to get detailed information about recycling this product please contact your retailer or a local authority.
SAFETY INFORMATION
- Use as intended. Improper usage may damage the device.
- Non-authorized repairs or disassembly voids the warranty and may damage the product.
- Dropping or hitting the device may lead to device being damaged, scratched or flawed in other way.
- Do not use the product in low and high temperatures, strong magnetic fields and damp or dusty surroundings.
GENERAL
- The safe product, conforming to the EU requirements.
- The product is made in accordance with RoHS European standard.
- 2 years limited manufacturer warranty
GENESIS. All rights reserved. GENESIS name and logo, and all related product and service names, design marks and slogans are the trademarks or registered trademarks of GENESIS. All other product and service marks contained herein are the trademarks of their respective owners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>