Godox M600D knowled daylight led light Instruction Manual

M600D knowledge daylight led light
Instruction Manual

IMPORTANT SAFETY INSTRUCTIONS

When using your photographic equipment basic safety precautions should always be followed, including the following:

1.  Read and understand all instructions before using.
2. Close supervision is necessary when any appliance is used by or near children. Do not leave the appliance unattended while in use.
3. Care must be taken as burns can occur from touching hot parts.
4. The appliance switch is provided with the symbols 0 indicating of and 1 indicating on. The symbols may be used for this purpose.
5. Do not operate any appliance with a damaged cord or if the appliance has been dropped or damaged – until it has been examined by a qualified serviceman.
6. Position the cord so that it will not be tripped over. pulled. or contact hot surfaces.
7. If an extension cord is necessary. a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.
8. Always unplug appliances from the electrical outlets before cleaning and servicing and when not in use. Never yank the cord to pull the plug from the outlet. Grasp plug and pull to disconnect.
9. Let the appliance cool completely before putting away Loop cord loosely around the appliance when storing.
10. To reduce the risk of electric shock. do not immerse this appliance in water or other liquids.
11. To reduce the risk of electric shock. do not disassemble this appliance, but take it to a qualified serviceman when service or repair work( is required. Incorrect reassembly can cause electric shock when the appliance is used subsequently
12. The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire. electric shock. or injury to persons.
13. Connect this appliance to a grounded outlet.
14. Disconnect this unit from its source of supply before replacing the projection lamp.
15. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock. this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet. reverse the plug. If it still does not fit. contact a qualified electrician. Do not modify the plug in any way

SAVE THESE INSTRUCTIONS

Foreword
Thank you for purchasing! Codex M600D is a LED Light product with a super performance. It has a separation design of a tight body and controller. high power. thousand-bit brightness adjustment and dimming curve adjustment functions. quite suitable for large photo studios. broadcast studios or large- scale field scenes.
Features:

• 600W high power to create bright light output.
• Brightness adjustment is accurate to 0.1%. controlling the tightness in subtle scenes.
• 4 dimming curves: linear. S-curve. exponential. and logarithmic.
• Bowens mount is perfectly compatible with more optical accessories. such as spotlight VSA.
• Venous professional control methods: Bluetooth control/DMX612 remote oantrov2.4G wireless control.
• Super high color rendering index: CRI: 296. TLCI: 297. R9: 293. R12: AS
• 12 simulated scenes by effects: hash. lightning. TV. broken bulb. etc.
• Two power supply methods: controller (DC) power supply and V-mount battery power supply
• Smart power supply. The controller can be charged while in use. and the side with the logo supports a unilateral power supply.
• Simple control interface: 4 buttons. 1 knob, clear Ul interface.

Warning

Always keep this prcceet cry- Do not use it in rain or in damp conditions.
Do not disassemble. Should repairs become necessary this product must be sent to an authorized maintenance center?
Keep out of reach of children.
As this product does not have a waterproof function. Please take measures of waterproof in a rainy or damp environment.
**Do not use the product in the presence of flammable gases. chemicals and other similar materials.
CAUTION: Hot pans. When the product is always on and flickering. please do not touch the high-temperature part of the LED head.
**When replacing product accessories. please turn off the LED light and perform a cold cut.
The tight source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person.
The tamp shaft is to be changed if it has become damaged or thermally deformed.
****The luminaire is intended for professional use only.

Name of Body

Light Body

Controller

Remote Control (Separately Sold Accessory)

What’s in the Box

Separately Sold Accessories

Better shooting effects and user experience matched with the following accessories: RC-A6 Remote Control, 8m Power Cord

Installation and Disassembly Guide

1. Connect the controller and the light body
   Press and hold the spring latch button of the connecting cord, and insert the end of the connecting cord with DC OUTPUT Port into the DC INPUT Port of the light body. Then continue to press and hold the button to insert the end of the connecting cord with DC INTPUT Port into the DC OUTPUT port of the controller to complete the connection.![Godox M600D knowled daylight led light

• 2](https://manuals.plus/wp-content/uploads/2022/06/Godox-M600D-knowled- daylight-led-light-2.png)

  2. Mounted on the tripod
     Adjust the light body to a proper angle, and rotate the screw of the sleeve knob to install the light body on the tripod. then rotate the screw of the sleeve knob to fix the light body on the tripod. The inclination angle of the light body could be adjusted by loosening the bracket angle adjustment handle and then screwing down the handle afterward.
     Note: The tripod belongs to separately sold accessories.

  3. Installation and disassembly of the lamp cover
     Installation: Press the small metal pusher top-down, put the lamp cover on Bowens Mount, and rotate clockwise to tighten it. Disassembly: Press the small metal pusher top-down, then rotate counterclockwise to remove it. Note: Make sure to remove the tamp cover before use to avoid damage. Put on the lamp cover to protect the lamp when not in use.

  4. Installation and disassembly of the standard reflector
     Installation: Press the small metal pusher top-down, put the standard reflector on Bowens Mount, and rotate clockwise to tighten it. Disassembly: Press the small metal pusher top-down, then rotate counterclockwise to remove it.

Installation Controller M600D-CL and DMX Controlling Box

The Connection operation diagram of Controller M600D-CL and DMX Controlling Box is as follows:

Power Supply

1. DC adapter Power Supply**** Note:

Please press the latch button when installing or disassembling the power cord and connecting cord.

2. V-mount battery power supply**** note:

usable for 14.4v-26v vmount battery

Display Screen

Controller Operation Instruction

1. Turn On/Off
   Short press the controller < > Button after connecting to the power supply to turn it on or off.

2. Brightness Adjustment (thousand-bit adjustment)
   Turn the SET adjustment knob on the main interface to adjust brightness from 0% to 100%, with an increment of 0.1% at each level. Rotate clockwise to increase brightness, and counterclockwise to decrease brightness. The brightness will increase or decrease by 0.1 unit at a normal rotation speed, and increase or decrease by 1 unit at a rapid rotation speed.

3. Menu Setting
   Short press < MENU > Menu Button to enter the menu interface, displayed in order with Wireless Control, Bluetooth, DMX Mode, Fan Mode, Dimming Curve, Screen Brightness Language, Restore Factory Setting, Version.

3.1 Wireless Control
Turn the SET adjustment knob on the menu interface and select Wireless control, then short press the SET adjustment knob again to enter the Wireless Control interface displayed in order with Wireless Switch, Channel, Group, and ID. Finally, complete the settings of Wireless Switch, Channel, Group, and ID by short pressing & turn the SET adjustment knob. 3.2 Bluetooth
Turn the SET adjustment knob on the menu interface and select < Bluetooth>, then short press the SET adjustment knob again to enter the Bluetooth Setting interface displayed in order with Bluetooth Switch, Reset, and MAC Code. Finally, complete the settings of Bluetooth Switch and Bluetooth Reset by short pressing & turn the SET adjustment knob. 3.3 DMX Mode
Turn the SET adjustment knob on the menu interface and select < DMX >, then short press the SET adjustment knob again to enter the DMX Setting interface displayed with Address Channel. Turn the knob to OFF or 1-512, the lamp will be in master or slave mode respectively. Afterward, short press the SET adjustment knob to return to the previous menu interface.

DMX Practical Form

rounding off
0-100% brightness adjustment
n+2| | DMX(Total Light Effect/255)| For Example Total Light
Effect 8,DMX=160, Light Effect
NO.=608/255=5
n+3| | 0-85: Light Effect Level I
86-171: Light Effect Level II
172-255: Light Effect Level Ill|
n+4
n+5

3.4 Fan Mode
Turn the SET adjustment knob on the menu interface and select < Fan >, then short press the SET adjustment knob again to enter the Fan Setting interface, and finally turn the knob to choose Auto Speed Adjustment Mode, High-Speed Fan Cooling Mode, Low-Speed Fan Cooling Mode, Off Mode. Note: Enter mute mode when turning off the fan.

3.5 Dimming Curve
Turn the SET adjustment knob on the menu interface and select < Dimming Curve >, then short press the SET adjustment knob again to enter the Dimming Curve Setting interface, finally turn the knob to choose linear/S-curve/exponential/logarithmic dimming curve. 3.6 Screen Brightness
Turn the SET adjustment knob on the menu interface and select < Screen Brightness >, then short press the SET adjustment knob again to enter the Screen Brightness Setting interface, finally turn the knob to choose 1, 2, or 3 levels of screen brightness. 3.7 Language
Turn the SET adjustment knob on the menu interface and select < Language >, then short press the SET adjustment knob again to enter the Language Setting interface, and finally turn the knob to choose English or Simplified Chinese 3.8 Restore Factory Setting
Turn the SET adjustment knob on the menu interface and select < Restore Factory Setting >, then short press the SET adjustment knob again to enter the Restore Factory Setting interface, turn the knob to choose “Yes” or ‘No” and short press to confirm. If you choose “Yes”, the system will initiate the resetting program and display the resetting progress bar on the screen, after which it will return to the main interface, and the screen brightness shows 50. 3.9 Version
Turn the SET adjustment knob on the menu interface and select < Version >, then short press the SET adjustment knob again to enter the Version display interface, the Version Code displayed on the screen is the firmware version of the Controller.

4. Light Effect Setting
   Short press the < /FX> button to enter the FX Light Effect interface, turn the knob to turn off Light Effect, or switch to flash lightning, TV, or broken bulb scenes.
   Note  Short press the SET adjustment knob to change the rate after choosing one of the above Light Effects.

Software Upgrade

1. Download the new firmware to the U disk from the official website (http://www.godox.com.cn/Downloads.html).
2. Turn off the M600D LED light. Insert the U disk with new firmware into the USB upgrade port.
3. Turn on the M600D LED Light, and it will automatically enter the upgrading interface.
4. 1t will return to the main interface after completion.

Notes:

1. New firmware must be downloaded from the official website. and keep only one BIN file in the root directory of the USB disk.
2. The USB port can only support the firmware upgrade function.

Over-Temperature Protection

If the temperature of the light body is too high. the Over-Temperature Protection icon flashes on the main interface. the light body can be used normally.
If the temperature of the light body exceeds the limit of Over-Temperature Protection. the Over-Temperature Protection icon flashes on the screen center, and the screen works properly after the light goes out in 3 seconds.
When the temperature decreases the Over-Temperature Protection icon disappears, then the light body can resume working.

Troubleshooting

If the! the icon appeared and blinked and the fan icon also appears on the display, It might be the fan failure. Please contact customer service. If the! the icon appeared and blinked and the temperature icon also appeared on the display:

1. If the icons are displayed in a cool-light state (just being turned on or for a little while), it might be probe failure. Please contact customer service.
2. If the icons are displayed in a hot-light state (being turned on for a long while), it might be caused by long-time usage and over-temperature. Please turn off the light and turn it on after the light is cooled down.

Maintenance

This product, except consumables e.g. adapter and power cable, is supported with a one-year warranty. Maintenance of the light must be performed by our authorized maintenance department which can provide original accessories. Unauthorized service will void the warranty. If the product breaks down or gets wet. please do not use it until repaired by a professional. If there is anything abnormal during the LED light’s working, please turn it off immediately and identify the reasons.

Illuminance Testing Data

133(FC)
Lamp with Cover
.| 164000(lux)
15200(FC)| 15700(lux)
1460(FC)| 5720(lux)
532(FC)

Technical Data

Bluetooth Control
Dimming Curve| 4 types: linear/S-curve/ exponential/logarithmic
Mute Mode| YES
2.4G Wireless Control Distance| ∼60m
Display Screen| 2.4 inches
Light Body| 447.3242.8-152.9mm
Controller| 332.4121.6-179.2mm
Light Body Weight| 4.5 kg
Controller Weight| 3.987 kg

• Product design and specifications are subject to change without notice.

Maintenance

This product, except consumables e.g. cable, is supported with a one-year warranty. Avoid sudden impacts and the product should be dedusted regularly.
Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by professionals.
Changes made to the specifications or designs may not be reflected in this manual.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference, and
2. this device must accept any interference received. including interference that may cause undesired operation.

Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body: Use only the supplied antenna.

Warranty

Dear customers, as this warranty card is an important certificate to apply for our maintenance service, please fill in the following form in coordination with the seller and safe-keep it. Thank you!

Address
Seller Information| Name
Contact Number
Address
Date of Sale
Note:

Note: This form shall be sealed by the seller
Applicable Products
The document applies to the products listed on the Product Maintenance Information (see below for further information). Other products or accessories (e.g. promotional items, giveaways, additional accessories attached, etc.) are not included in this warranty scope.
Warranty Period
The warranty period of products and accessories is implemented according to the relevant Product Maintenance Information. The warranty period is calculated from the day(purchase date) when the product is bought for the first time, And the purchase date is considered as the date registered on the warranty card when buying the product.
How to Get the Maintenance Service
If maintenance service is needed, you can directly contact the product distributor or authorized service institutions. You can also contact the Godox after-sale service call and we will offer you service. When applying for maintenance service, you should provide a valid warranty card. If you cannot provide a valid warranty card, we may offer you maintenance service once confirmed that the product or accessory is involved in the maintenance scope, but that shall not be considered our obligation.
Inapplicable Cases
The guarantee and service offered by this document are not applicable in the following Cases:

1. The product or accessory has expired its warranty period;
2. Breakage or damage caused by inappropriate usage, maintenance, or preservation, such as improper packing, improper usage, improper plugging in/out external equipment, falling off or squeezing by an external force, contacting or exposing to the improper temperature, solvent, acid, base, flooding, and damp environments, etc;
3. Breakage or damage caused by the non-authorized institution or staff in the process of installation, maintenance, alteration, addition, and detachment;
4. The original identifying information of the product or accessory is modified, alternated, or removed;
5. No valid warranty card;
6. Breakage or damage caused by using illegally authorized, nonstandard, or non-public released software;
7. Breakage or damage caused by force majeure or accident;
8. Breakage or damage that could not be attributed to the product itself. Once met these situations above, you should seek solutions from the related responsible parties and Godox assumes no responsibility. The damage caused by parts, accessories, and software that is beyond the warranty period or scope is not included in our maintenance scope. The normal discoloration, abrasion, and consumption are not the breakages within the maintenance scope.

Maintenance and Service Support Information
The warranty period and service types of products are implemented according to the following Product Maintenance Information:

Product Type| Name| Maintenance Period(month)| Warranty Service Type
---|---|---|---
Parts| Circuit Board| 12| The customer sends the product to the designated site
Battery| 3| The customer sends the product to the designated site
Electrical parts e.g.battery charger, power cord, sync cable, etc.| 12| The customer sends the product to the designated site
Other Items| Flash tube, modeling lamp, lamp body, lamp cover, locking device, package, etc.| No| Without warranty

Godox After-sale Service Call 0755-29609320-8062

Made in China
GODOX Photo Equipment Co., Ltd.
Add: Building 2, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Baoan District
Shenzhen 518103, China
Tel: +86-755-29609320(8062)
Fax: +86-755-25723423
E-mail: godox@godox.comgodox.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>