Jr Auto Performance MHD OBD2 Flasher Enet Wi-Fi User Manual
- June 5, 2024
- Jr Auto Performance
Table of Contents
MHD OBD2 Flasher Enet Wi-Fi
User Manual
Overview
MHD OBD2 Wifi Flasher was specially developed and designed to operate the Ethernet OBD2 diagnostic and coding features via wired J2534 port and wireless via an embedded module based on the universal serial interface network standard, built-in TCP / IP protocol stack, enabling the user serial port, Ethernet, wireless network (wifi) interface between the conversions. the traditional serial devices do not demand to change any configuration, data can be transmitted through the Internet network. Provide a quick solution for the user’s serial devices to transfer data via Ethernet
Features
-
2.4GHz 802.11b/g/n,compatible
-
Support IEEE 802.3、IEEE 802.3u
-
WiFi Client/AP/Router Mode
-
Support WPS/wds
-
The range of baudrate: 1200~500000bps
-
Support transparent transmission mode
-
Support multiple security authentication mechanisms:
WEP64/WEP128/ TKIP/ AES
WEP/WPA-PSK/WPA2-PSK -
Support wireless roam
-
Support multiple network protocols:
PPPOE/TCP/UDP/DNS /DHCP/DNS/HTTP/Firewire -
Support AT+ instruction set
-
Support two config methods: Serial/WEB
-
Device Dimensions 874726mm
Applications
Ethernet OBDII WiFi Diagnose
Specifications
The parameters are defined here.
Typical DC Characteristics | Notes |
---|---|
Only wifi current | 140mA |
One rj45 current | 12OrnA |
Two rj45 current | 135mA |
Win and two 1145 | 160mA |
Center frequency accuracy | +/- 25ppm |
Typical RF Characteristics U | Notes |
Receive sensitivity | -70d8m |
Maximum Transmit power | 18d8m/15d8m/13.5013m |
RF Port impedance – Ipax connector | 50 ohm |
VSWR (max) | 2:01 |
Center frequency accuracy | +/- 25ppm |
Peripherals | Notes |
CART | 2pins |
RJ45(WAN) | 4pins |
RJ45(LAN) | 4pins |
3.3V Out | 1 pin |
1SV Out | 1 pin |
Wi-Fi Module Pin Assignment
Pin No | Signal Type | Description |
---|---|---|
1 | VCC5V | Supply Voltage, 5V+/-10% |
2 | GND | Analogue Ground |
3 | WINFIELD | WLAN Activity LED |
4 | V03.3 | 3.3V Output (Support Almost 300mA) |
5 | LINK1 | 10/100 PHY Port #1 activity LED |
6 | N/A | Reserved |
7 | N/A | Reserved |
8 | GOOD | General GPIO Reserved |
9 | GPIO1 | General GPIO Reserved |
10 | FIRST | Exit transparent transmission mode/Restore factory value |
11 | TX0P I | 10/100 PHY Port #1 TXP |
12 | TX0N I | 10/100 PHY Port #1 TXN |
13 | RXIP2 | 10/100 PHY Port #2 TXP |
14 | RXIN2 | 10/100 PHY Port #2 TXN |
15 | RXIPI | 10/100 PHY Port #1 RXN |
16 | RXIPI | 10/100 PHY Port #1 RXP |
17 | TXON2 | 101100 PHY Port #2 OXN |
18 | TX0P2 | 10/100 PHY Port #2 OXP |
19 | GP102 | General GPIO Reserved |
20 | UARTRX | CART RDX. |
21 | UART TX | UART TXD. |
22 | 1,103 | General GPIO Reserved |
23 | LINK2 | 10/100 PHY Port #2 activity LED |
24 | 6P104 | General GPIO Reserved |
25 | WPSItST | WiFi Protected Setup /Restore factory value |
26 | GPIOS | General GPIO Reserved |
27 | V01.8 | 1.8V Output (Support Almost 300mA) |
28 | VCC5V | Supply Voltage, 5V+/-10% |
Electrical Characteristics
Parameter | Min | Max |
---|---|---|
Module supply voltage VCC | 3.9V | 5.5V |
Module Vokage Output V03.3 | 3.1V | 4. |
Module Vokage Output V01.8 | 1.65V | 2. |
GPIO Voltage | 3.1V | 3.5V |
Storage temperature | -40°C | 95°C |
Operation Guidelines to work with car OBDII
Step 1: Ignition ON, plug the MHD OBDII wifi flasher into the OBD2
diagnostic port
Step 2: Search the Wifi ISID started with MHD_XXXX from laptop wifi and
access with the password sated at the back side of the module. Step 3:
Successfully connected and operated as user demanded via OBD2 diagnostic port.
Step 4: Administration panel setup for administrators only.
Appendix Disclaimers
The contents of this document are subject to change without notice. Autosvs
Technology reserves the right to make changes, without notice, in the
products, including circuits and/or software, described or contained therein.
Information contained in this document regarding device applications and the
like is intended through suggestion only and may be superseded by updates. It
is your responsibility to ensure that your application meets your
specifications.
Autosvs Technology warrants the performance of its hardware products to the
specifications applicable at the time of sale in accordance with Autosvs
Technology’s standard warranty. Testing and other quality control techniques
are used to the extent Autosvs Technology deems necessary to support this
warranty. Except where mandatory by government requirements, testing of all
parameters of each product is not necessarily performed.
Autosvs Technology assumes no responsibility or liability for the use of any
of these products, conveys no license or title under any patent, copyright, or
mask work right to these products, and makes no representations or warranties
that these products are free from patent, copyright, or mask work infringement
unless otherwise specified.
Autosvs Technology products are not intended for use in life support systems,
appliances, or systems where malfunction of these products can reasonably be
expected to result in personal injury, death, or severe property or
environmental damage. Autosvs Technology customers using or selling these
products for use in such applications do so at their own risk and agree to
fully indemnify Autosvs Technology for any damages resulting from such use.
All products are sold subject to Autosvs Technology’s terms and conditions of
sale supplied at the time of order acknowledgment. All trademarks are the
property of their respective owners.
NB Warning:
Manufacturer’s Name: JR Auto Performance Inc.
Sample Description: MG Flasher Enet Wifi
Trade Mark: /
Model number: MG Flasher Enet Wifi
Operating Temperature: -10° C to 40° C
Wireless specification:
2.4G WIFI: Max power 14.38dbm in frequency band 2412-2462MHz
This product is in a fixed location. To comply with RF exposure requirements,
a minimum separation distance of 20cm must be maintained between the user’s
body and the device, including the antenna. The device complies with RF
specifications when the device is used at 20cm from your body.
Use only the supplied or an approved antenna.
This device is in compliance with the essential requirements and other
relevant provisions of Directive 2014/53/EU. All essential radio test suites
have been carried out.
FCC Warning:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body: Use only the supplied antenna.
FCC ID: 2AWSB-MGENET
Documents / Resources
| Jr
Auto Performance MHD OBD2 Flasher Enet Wi-
Fi
[pdf] User Manual
MGENET, 2AWSB-MGENET, 2AWSBMGENET, MHD OBD2 Flasher Enet Wi-Fi, MHD OBD2,
Flasher Enet Wi-Fi
---|---