KONNEK STEIN QC21SE Indoor Security Camera User Guide
- June 5, 2024
- KONNEK STEIN
Table of Contents
- Product Introduction
- Camera Information
- Product Installation
- Basic Parameters
- Install the App
- Scan QR Code Mode
- Wi-Fi Mode
- App Video Interface Information
- Points For Attention
- The Name and Content of Hazardous Substance in the Product
- Other Information
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
STEIN QC21SE Indoor Security Camera
User Guide
Product Introduction
Package list:
- Camera Xl,
- USB Power Cord Xl, Power
- Adapter Xl,
- Screw Kit Xl,
- Mounting Bracket X1,
- User Manual X1
Camera Information
Note: Please don’t force the camera to turn around manually
- Light Sensor
- Lens
- Microphone
- TF Card Slot
- Speaker
- Reset Button
- Power Interface
Product Installation
- Place the mounting bracket on the wall before punching, mark it with a marker pen, then punch the hole
- Insert the plastic anchor into the hole
- Install the mounting bracket to the wall with a screwdriver and screws
- Finally, install the camera on the wall with a mounting bracket
Note: upside-down and normal direction both methods are supported in the aspect of the installation
Basic Parameters
Product Name: Indoor Security Camera
Product Model: QC21SE
Video Resolution: 2.0MP,1920*1080
Video Coding-Decoding Technology: H.264
Image Enhancement: Digital Wide Dynamic, 3D Noise
Storage: TF Card/Cloud Storage
Wireless Encryption: WEP / WPA / WPA2
Power Input: 5V =1A(Min)
Total Power Consumption: 5W (Max)
Wireless Standard: 2.4G 802.11 b/g/n
Compatible System: Android/IOS
Note:
- To reset the camera: Long press the reset button for about 5 seconds when reconnecting the camera. There will prompt tone when resetting successfully
- Please insert a TF card with the speed of class 10 or above, or it may cause storage abnormalities. The video files in the TF card will be overwritten cyclically when storage is full
- In order to protect users’ privacy, the stored data will be encrypted. It can avoid video leakage, even if the TF card was lost accidentally.
(Note: The storage data on the TF card of the device can’t be copied to the computer for review)
Install the App
- Scan the QR code below to download and install the App
- Or search the App name of·smart Life” in App Store or Google Play to download
http://smartapp.tuya.com/smartlife?from=singlemessage&isappinstalled=0
Scan QR Code Mode
- Please make sure that Wi-Fi is available and the phone is connected to the network, and power on the camera through the adapter and power cord
- Open the App of “Smart life’. Click the sign “+” in the top right corner of homepage (Picture 01). Select “Security&Video Surveillance·: click ‘Smart Camera(Wi-Fi) “to add a camera(Picture 02). Click the button of ” QR Code” in the top right corner, then you will see other modes there, choose” Wi-Fi Mode” (Picture 03)
- If the phone is not connected to Wi-Fi, please click”Go to connect” (Picture 04)
- It will jump to the interface like picture 05, please be noted that only 2.4G Wi-F1 is supported
- If the phone is connected to Wi-Fi (Picture 06), please click”Next”
- The App will generate a QR code and use a camera lens to scan the QR code(Please keep the distance between the camera and QR code within 20-30cm). A prompt tone will be heard if the scan is successful. Click the button “I heard a prompt” (Picture 07)
- The device is being added (Picture 08)
- The camera will be added successfully when jumping to picture 09. Then click the button “Done·. The interface will jump to preview like picture 10
- Back to the homepage of the App from the preview, then the added devices will all appear on the homepage (Pictu「e 11). You can click the added device directly to view monitoring status next time instead of adding it again
Wi-Fi Mode
(Ⅰ) EZ Mode
-
Please make sure that Wi-Fi is available and the phone is connected to the network, and then power on the camera through the adapter and power cord.
-
Open the App of “Smart life: Click the sign “+” in the top right corner of the homepage (Picture12). Select “Security&Video Surveillance’: click “Smart Camera (Wi-Fi)” to add a camera (Picture 13). Click the button of ” OR Code” in the top right corner, then you will see other modes there, choose” Wi-Fi Mode” (Picture 14).
-
The interface jumps to picture 15, click “Next”. select the “EZ Mode” (Picture16)
Note: This device has no indicator light, please operate according to the instructions -
Click the “EZ Mode’, the interface will jump to picture 17. Connect to Wi-Fi, enter the account and password, and click “Next”
-
Return back to App after connecting completed. You can see that the device is being added (Picture 18)
-
After adding successfully, the interface will jump to picture 19
-
Click the button “Done” on the top right corner. The interface will jump back to the preview interface (Picture 20)
(II) AP Mode:
-
Please make sure that Wi-Fi is available and the phone is connected to the network, and power on the camera through the adapter and power cord
-
Short press the reset button for less than one second to shift AP mode
-
Open the App of “Smart life”, and click the sign of’+” in the top right corner of homepage (Picture 21). Select “Security&Video Surveillance”, and click “Smart Camera(Wi-Fi)” to add a camera (Picture 22). Click the “QR code” in the top right corner, then you will see other modes there, choose ” Wi-Fi Mode”. (Picture23)
-
The interface jumps to picture 24, click “Next”. Select the “AP Mode” (Picture25)
Note: This device has no indicator light, please operate according to the instructions -
Click the “AP Mode’, and the interface will jump to picture 26. Connect to Wi-Fi, enter the account and password, click “Next”
-
The App will jump to the interface (Picture 27), click”Go to Connect” at the bottom of the page
-
Then will jump to the WLAN connection interface of your phone, choose the hotspot starting with”Smart Life_xxxx” (Picture 28)
-
Return back to App after connecting completed. You can see that the device is being added (Picture 29)
-
The camera will be added successfully when jumping to picture 30. Then click the button “Done”. The interface will jump to preview like picture 31
-
Back to the homepage of the App from the preview, then the added devices will al I appear on the homepage(Picture 32). You can click the added device directly to view monitoring status next time instead of adding it again
App Video Interface Information
- Preview Mode
- Voice
- Long Screen
- Time
- Microphone
- Picture
- Full Screen
- Video
- More
Points For Attention
- Stay away from metal objects
- Please avoid placing the camera on the back of the furniture or inside the microwave oven
- Please avoid placing the camera somewhere surrounded by audio cables, video cables, and USB cables. And try to keep away from cables as far as possible
- Please try to make the camera within the Wi-Fi signal range. If too far to connect, may change to another network that is within the range
- If you need to change to a new network, please remove the device from App first(Press the device on the homepage for about 1 second, then a prompt message of “Remove Device” will appear at the bottom of the App). Tap the reset button on the device for about 5 seconds, then start to connect to the new network
The Name and Content of Hazardous Substance in the Product
Part Name | Hazardous Substance |
---|---|
Pb | Hg |
Shell | Ο |
Board | Χ |
Charger | Ο |
Annex | Ο |
This form is based on the provisions of SJfT 11364 。
This product complies with the environmental requirements of RoHS. At present, there is no mature technology in the world that can replace or reduce the contents of lead-in electronic ceramics, ceramics, optical glass, steel and copper alloys
Other Information
FCC ID: 2AVTM-QC21SE
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation
WARNING: This product can expose you to chemicals including Pb, which are
known to the State of California to cause cancer and birth defects or other
reproductive harm.For more information go to
www.P65Warnings.ca.go
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20cm between the radiator and your body.
Customer Service Email:
customerservice@ttinno.com
Any support you need, anything you feel like sharing,
You are more than welcome to contact us
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>