WRS INTERNATIONAL 6401A Agressor Dry Suit Water Rescue Equipment and Inflatables Instruction Manual
- June 5, 2024
- WRS INTERNATIONAL
Table of Contents
WRS INTERNATIONAL 6401A Agressor Dry Suit Water Rescue Equipment and
Inflatables
User Instructions Dry Suits
TOB BE READ BEFORE TRYING ON OR USING WARNING
Water based activities are dangerous and tuition form a qualified instructor
should be undertaken. It is possible that the materials in this dry suit, such
as latex, might cause an allergic reaction.
Dry Suit risks and limitations
Dry Suits are designed to keep you dry; Warmth is provided by underclothing.
The amount of thermal protection required from the undergarments depend on the
factors such as water temperature, air temperature, physiology, and work rate.
Incorrect undergarment selection could lead to either Hyperthermia or
Hypothermia and training and advice should be sought from an instructor.
Dressing
Avoid damage to the suit by standing on a clean surface free of sharp objects
or gravel which can cut the latex feet and damage the suit fabric . Remove
watches, rings and anytime that could damage the seals before putting on.
Check all zippers are fully closed and vent the suit by crouching down and
allowing air to escape by opening the neck seal. When undressing open the neck
seal with both hands before pulling over head..
Fit
You should be able to move freely when wearing the suit. Check this by wearing
the appropriate clothing, without any restrictions you should be able to
crouch down, raise the arms above the head and raise one leg with the thigh
parallel to the ground. The latex seals can be increased in size by cutting
just above the moulded rings on the latex seal, ensuring no nicks that can
cause a weakness to the seal.
Care and Maintenance
Seals Apply French Chalk or non-scented talk to the seals before storing and
before donning. Latex seals are the most vulnerable part of the suit – store
them in a cool, dark, uncontaminated atmosphere with no sharp creases and they
should last for at least 9 months and should work for some time after that.Zip
Care – After use close the zip and wash it with clean fresh water, ensuring
the zip teeth are free from sand, grit and dust. If the zipper is metal then
lubricate the teeth with a candle or beeswax stick. If the Zipper snags then
clean the teeth before closing further- never force the zip
For YKK plastic zippers clean as above, use only a small drop of silicon
lubricate to keep the zip in good condition. (Don’t use wax on a Plastic
Zipper) General information – Contact with oil, petrol, paraffin diesel and
other similar fuels or solvents will perish the latex and should be avoided.
Any contaminants should be washed off immediately with soapy water to minimise
damage.Storage The Suit should be dried inside and out, then stored on a
padded coat hanger between 0 to 20 degrees Celsius . The suit should be stored
away from direct heat, sunlight or sources of ozone (e.g. electric motors).
Washing Wash thoroughly with fresh water to remove any dirt, sand or salt and
drip dry.
Disposal
Follow local regulations on prescriptions for disposing of your dry suit at the end of its useful life.
Inspection and Repair
The dry suit should be visually inspected both before and after use. The seals
should be inspected for rips, tears and perishing. The seam tape on the suit
should be checked for lifting and tears. The zip should be inspected for
faulty teeth, cracking, or tears in the mould. The Fabric should be inspected
for rips, tears and delamination. If the suit is not being used regularly then
it should be checked every 6 months. Zips, seals, and seam tape can be
repaired, however when the fabric has delaminated the suit is no longer fit
for purpose, check with manufacture for advice on the suits repair
possibilities.
A full maintenance service is available through your local dealer or contact
WRS International directly. Simple repairs such as patching holes can be
carried out by the user.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>