makita UH4261 420mm Electric Hedge Trimmer Instruction Manual
- June 5, 2024
- Makita
Table of Contents
UH4261 420mm Electric Hedge Trimmer
Instruction Manual
|
---|---
Explanation of general view
1. Switch trigger B | 9. Holder | 17. Press |
---|---|---|
2. Switch trigger A | 10. Waist cord hook | 18. Chip receiver |
3. Switch trigger C | 11. Cord | 19. Nut |
4. Hook complete | 12. Arm cord hook band | 20. Shear blade |
5. Tool’s cord | 13. Trimming direction | 21. Hooks |
6. Extension cord | 14. Tilt the blades | 22. Fit the hooks into the groove |
7. Hook | 15. Hedge surface to be trimmed | 23. Grooves |
8. Tool | 16. String | 24. Press the hooks on both sides |
25. Unlock the hooks
SPECIFICATIONS
Model | UH4261 | UH4861 | UH5261 |
---|---|---|---|
Blade length | 420 mm | 480 mm | 520 mm |
Strokes per minute (min-¹) | 1,600 | 1,600 | 1,600 |
Overall length | 821 mm | 871 mm | 921 mm |
Net weight | 2.9 kg | 3.0 kg | 3.0 kg |
Safety class | /II |
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
| Read the instruction manual.
---|---
| DOUBLE INSULATION
| Do not expose to rain.
| Remove plug from the mains immediately if the cable is damaged or cut.
| Only EU countries
Do not dispose of electric equipment together with household waste material!
In observance of European Directive 2002/96/EC on waste electrical and
electronic equipment and its implementation in accordance with national law,
electric equipment that has reached the end of its life must be collected
separately and returned to an environmentally compatible recycling facility.
Intended use
The tool is intended for trimming hedges.
Power supply
The tool should be connected only to a power supply of the same voltage as
indicated on the nameplate, and can only be operated on a single-phase AC
supply. They are
double-insulated in accordance with European Standard and can, therefore, also
be used from sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
HEDGE TRIMMER SAFETY WARNINGS
-
Hold the power tool by insulated gripping surfaces only, because the cutter blade may contact hidden wiring or its own cord. Cutter blades contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Keep all parts of the body away from the cutter blade. Do not remove cut material or hold material to be cut when blades are moving. Make sure the switch is off when clearing jammed material. A moment of inattention while operating the hedge trimmer may result in serious personal injury.
-
Carry the hedge trimmer by the handle with the cutter blade stopped. When transporting or storing the hedge trimmer always fits the cutting device cover. Proper handling of the hedge trimmer will reduce possible personal injury from the cutter blades.
-
Keep the cable away from the cutting area. During operation, the cable may be hidden in shrubs and can be accidentally cut by the blade.
-
Do not use the hedge trimmer in the rain or in wet or very damp conditions. The electric motor is not waterproof.
-
First-time users should have an experienced hedge trimmer user show them how to use the trimmer.
-
The hedge trimmer must not be used by children or young persons under 18 years of age. Young persons over 16 years of age may be exempted from this restriction if they are undergoing training under the supervision of an expert.
-
Use the hedge trimmer only if you are in good physical condition. If you are tired, your attention will be reduced. Be especially careful at the end of a working day. Perform all work calmly and carefully. The user is responsible for all damages to third parties.
-
Never use the trimmer when under the influence of alcohol, drugs or medication.
-
Check to make sure that the voltage and frequency of the power supply correspond to the specifications given on the identification plate. We recommend the use of a residual-current-operated circuit breaker (ground-fault circuit interrupter) with a tripping current of 30 mA or less, or an earth leakage current protector.
-
Work gloves of stout leather are part of the basic equipment of the hedge trimmer and must always be worn when working with it. Also, wear sturdy shoes with anti-skid soles.
-
Before starting work check to make sure that the trimmer is in good and safe working order. Ensure guards are fitted properly. Check cable for damage before starting work and replace it if necessary. The hedge trimmer must not be used unless fully assembled.
-
Keep the cable away from the cutting area. Always work in such a way that the extension power cord is behind you.
-
Remove plug from the mains immediately if the cable is damaged or cut.
-
Make sure you have a secure footing before starting operation.
-
Hold the tool firmly when using the tool.
-
Do not operate the tool at no-load unnecessarily.
-
Immediately switch off the motor and unplug the mains plug if the cutter should come into contact with a fence or other hard object. Check the cutter for damage, and if damaged repair immediately.
-
Before checking the cutter, taking care of faults, or removing material caught in the cutter, always switch off the trimmer and unplug the mains plug.
-
Switch off the trimmer and disconnect and secure the mains plug before doing any maintenance work.
-
When moving the hedge trimmer to another location, including during work, always unplug the mains plug and put the blade cover on the cutter blades. Never carry or transport the trimmer with the cutter running.
Never grasp the cutter with your hands. -
Clean the hedge trimmer and especially the cutter after use, and before putting the trimmer into storage for extended periods. Lightly oil the cutter and put on the cover. The cover supplied with the unit can be hung on the wall, providing a safe and practical way to store the hedge trimmer.
-
Store the hedge trimmer with the cover on, in a dry room. Keep it out of reach of children. Never store the trimmer outdoors.
-
Do not operate the tool at no-load unnecessarily.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with the product (gained from repeated use)
replace strict adherence to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
Always be sure that the tool is switched off and unplugged before
adjusting or checking the function on the tool.
Put the blade cover on the shear blades before adjusting or checking the
function of the tool.
Switch action (Fig. 1)
For your safety, this tool is equipped with a triple switching system. To turn
on the tool, press switch trigger B and press switch trigger A or C at the
same time. Release either one of the two pressed switch triggers to turn off.
The sequence of switching is unimportant as the tool only starts when both
switches are activated.
Straight cut (Fig. 2)
To trim the hedge straight, the pull switch triggers A and B.
Vertical cut (Fig. 3)
Cut upwards with both hands pull the switch triggers B and C and move it in
front of your body.
ASSEMBLY
CAUTION:
- Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Engage the extension cord
CAUTION:
- Make sure that the extension cord is unplugged from the main outlet. (Fig. 4)
When engaging the extension cord, secure it to the tool’s cord with the hook complete. Attach the hook about 100 – 200 mm from the extension cord connector. This will help prevent unintentional disconnection.
Waist cord hook
CAUTION:
- Do not attach the holder of the waist cord hook to other than the extension cord. Do not attach it in a position closer to the tool beyond the hook complete. Failure to do so may cause an accident or personal injury.
- Attach firmly one hook of the hook complete to the tool’s cord and the other hook of hook complete to the extension cord. Working with the tool with a sole hook only attached may cause an accident and injury.
Using the waist cord hook helps to minimize the risk of cutting off the
extension cord unexpectedly caused by the loose extension cord. (Fig. 5 & 6)
Press in or pull out the cord through the opening of the holder.
CAUTION:
- Do not force the opening of the holder. Failure to do so may cause deflection and damage to it.
Arm cord hook (accessory)
CAUTION:
- Do not attach the holder of the arm cord hook to other than the extension cord. Do not attach it in a position closer to the tool beyond the hook complete hooks. Failure to do so may cause an accident or personal injury.
- Attach firmly one hook of the hook complete to the tool’s cord and the other hook of hook complete to the extension cord. Working with the tool with a sole hook only attached may cause an accident and injury.
Using the arm cord hook helps to minimize the risk of cutting off the extension cord unexpectedly caused by the loose extension cord. (Fig. 7)
Attach firmly the arm cord hook band placed around your arm and pass the extension cord through the holder. The length of the arm cord hook band is adjustable.
NOTE:
- Do not pass the extension cord through the band.
- Do not force the opening of the holder. Failure to do so may cause deflection and damage to it.
- Using the arm cord hook together with the waist cord hook is more helpful.
OPERATION
CAUTION:
- Be careful not to accidentally contact a metal fence or other hard objects while trimming. The blade will break and may cause serious injury.
- Overreaching with a hedge trimmer, particularly from a ladder, is extremely dangerous. Do not work from anything wobbly or infirm. (Fig. 8)
Do not attempt to cut branches thicker than 10 mm in diameter with this trimmer. These should first be cut with shears down to the hedge trimming level.
CAUTION:
- Do not cut off dead trees or similarly hard objects.
Failure to do so may damage the tool. (Fig. 9)
Hold the trimmer with both hands pull the switch trigger A or B and move it in
front of your body. (Fig. 9 & 10)
As a basic operation, tilt the blades towards the trimming direction and move
it calmly and slowly at the speed rate of 3 – 4 seconds per meter. (Fig. 11)
To cut a hedge top evenly, it helps to tie a string at the desired hedge
height and to trim along it, using it as a reference line. (Fig. 12)
Attaching the chip receiver (accessory) to the tool when trimming the hedge
straight can avoid cut-off leaves being thrown away. (Fig. 13)
To cut a hedge side evenly, it helps to cut from the bottom upwards. (Fig. 14)
Trim boxwood or rhododendron from the base toward the top for a nice
appearance and good job.
Installing or removing chip receiver (accessory)
CAUTION:
- Always be sure that the tool is switched off and unplugged before installing or removing the chip receiver.
NOTE:
-
When replacing the chip receiver, always wear gloves so that hands and face do not directly contact the blade. Failure to do so may cause personal injury.
Always be sure to remove the blade cover before installing the chip receiver. -
The chip receiver receives cut-off leaves and alleviates collecting thrown-away leaves. This can be installed on either side of the tool. (Fig. 15 & 16)
At this time, the chip receiver needs to be installed so that its hooks fit into grooves in the shear blade unit. (Fig. 17) To remove the chip receiver, press its lever on both sides so that the hooks are unlocked.
CAUTION:
- The blade cover (standard equipment) cannot be installed on the tool with the chip receiver being installed. Before carrying or storing, uninstall the chip receiver and then install the blade cover to avoid blade exposure.
NOTE:
- Check the chip receiver for secure installment before use.
- Never try to uninstall the chip receiver by excessive force with its hooks locked in the blade unit grooves.
Using excessive force may damage it.
MAINTENANCE
CAUTION:
- Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
Cleaning the tool
Clean out the tool by wiping off dust with a dry or soap-dipped rag.
CAUTION:
- Never use gasoline, benzene, thinner, alcohol, or the like. Discoloration, deformation, or cracks may result.
Blade maintenance
Smear the blade before and once per half an hour during operation using
machine oil or similars.
After the operation, remove dust from both sides of the blade with a wired
brush, wipe off it with a rag and then apply enough low-viscosity oil, such as
machine oil etc., and
spray-type lubricating oil.
CAUTION:
- Do not wash the blades in the water. Failure to do so may cause rust or damage to the tool.
- Wear gloves when performing blade maintenance.
Storage
Put the blade cover on the shear blades so that the blades are not exposed.
Store the tool out of the reach of children carefully.
Store the tool in a place not exposed to water and rain.
To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection,
and replacement, and any other maintenance or adjustment should be performed
by Makita Authorized Service Centers, always using Makita replacement parts.
OPTIONAL ACCESSORIES
NOTE:
- Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
The typical A-weighted noise level is determined according to EN60745:
Sound pressure level (LpA): 82 dB (A)
Sound power level (LWA): 93 dB (A)
Uncertainty (K): 2.1 dB (A)
Wear ear protection.
Vibration
The vibration total value (tri-axial vector sum) determined according to
EN60745:
Work mode: hedge trimming
Vibration emission (ah): 6.7 m/s2
Uncertainty (K): 1.5 m/s 2
- The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
- The declared vibration emission value may also be used in a preliminary assessment of exposure.
WARNING:
- The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.
- Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible manufacturer declares that the
following Makita machine(s):
Designation of Machine:
Hedge Trimmer
Model No./ Type: UH4261, UH4861, UH5261
Specifications: see the “SPECIFICATIONS” table. are of series production and
Conforms to the following European Directives: 2000/14/EC, 2006/42/EC
And are manufactured in accordance with the following standards or
standardized documents: EN60745
The technical documentation is kept by our authorized representative in Europe
who is:
Makita International Europe Ltd.
Michigan Drive, Tongwell,
Milton Keynes, Bucks MK15 8JD, England
The conformity assessment procedure required by
Directive 2000/14/EC was in Accordance with annex V.
Measured Sound Power Level: 93 dB (A)
Guaranteed Sound Power Level: 96 dB (A)
23. 07. 2010
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, 446-8502, JAPAN
Makita Corporation
Anjo, Aichi, Japan
www.makita.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>