Marshall WOBURN III Bluetooth Speaker Instructions

WOBURN III Home Bluetooth Speaker
User Manual

This is an interactive document, click on the section you are looking for.

1. 3.5 MM INPUT
   Plug in an analog audio device with a 3.5 mm stereo jack.

2. SOURCE SELECTION
   Push the source button to toggle between Bluetooth®, AUX, RCA, and HDMI audio sources. A lit indicator shows which source is selected.
   This can also be selected from the Marshall Bluetooth app.
   Caution:  Make sure that the volume is set to low on both the speaker and the audio device before using the speaker.

3. AUDIO CONTROLS
   Woburn III includes three controls for adjusting the audio.
   I. Volume control
   II. Bass control
   III. Treble control

4. MEDIA CONTROL
   Control the audio directly from the top panel when playing via Bluetooth.
   I. Push to play or pause
   II. Push right to skip forward
   III. Push left to skip back
   IV. Hold left or right to rewind or fast forward
   Playback can also be controlled from the Marshall Bluetooth app.

5. POWER SWITCH
   Use the power switch to turn the speaker on or off.
   

6. RCA INPUT (LEFT AND RIGHT)
   Plug in an RCA audio device, such as an RIAA turntable.

7. HDMI ARC INPUT
   Plug in an HDMI-supported TV.

8. POWER INPUT
   Use the included mains lead to connect Woburn III to the wall socket.

INSTRUCTIONS

GETTING STARTED

1. Connect the mains lead to the mains input on your speaker, then connect the mains plug to the wall socket.
2. Use the power switch to turn the speaker on.
3. Download the Marshall Bluetooth app and follow the in-app instructions to set up your speaker.
   Important: Always ensure that the mains lead, plug, and speaker are compatible with your mains supply and wall socket.
   Caution:  Always unplug the mains lead from the wall socket before disconnecting it from the speaker.

BLUETOOTH PAIRING

1. Use the source button to select Bluetooth.
2. Push and hold the source button until the Bluetooth LED pulses red.
3. Select WOBURN III from your audio device’s Bluetooth list.
   Woburn III can be connected to two Bluetooth devices at the same time. If a connected device is playing, a second connected device cannot start playing until the first device is paused.

CONNECTING AN AUX DEVICE

1. Connect a 3.5 mm stereo jack to the AUX input on the top of the speaker.
2. Connect the other end of the lead to the audio output on your audio source.
3. Use the source button to select AUX.
   Note:  Audio leads are not included.

CONNECTING AN RCA DEVICE

1. Connect a lead with RCA jacks to the RCA input on the back of the speaker.
2. Connect the other end of the lead to the output on your audio source.
3. Use the source button to select RCA.
   Note: The turntable must be equipped with an RIAA amplifier or connected via a separate preamplifier. Audio lead and RIAA amplifier are not included.

CONNECTING A TV WITH HDMI

1. Plug an HDMI lead into the HDMI port on the back of Woburn III and the HDMI ARC port on your TV.
2. Turn on the speaker and use the source button to select HDMI.
3. Turn on your TV and select HDMI ARC audio output and choose PCM (2-channel) as a format.
   If Woburn III is powered on and connected to a TV, turning on the TV will auto-select HDMI as the source.
   Note: HDMI leads are not included. For information about your TV’s HDMI support, labeling of ports, and user instructions, please consult its user manual.

NETWORK STANDBY MODE
Woburn III will go into network standby if left unused for 10 minutes to save energy. Any connected Bluetooth device will be disconnected. Interact with any control or button on the top panel, reconnect a Bluetooth device or play anything via the physical inputs to wake up the speaker.

PERFORMING A FACTORY RESET
A factory reset will return the speaker to its original settings, excluding any firmware updates.
Note: This will delete all user settings and the speaker needs to be set up again.

1. Push and hold the media control for more than 10 seconds and the speaker will reset.
2. Remove WOBURN III from your audio device’s Bluetooth list before pairing again.

MARSHALL BLUETOOTH APP
Download the Marshall Bluetooth app to get the most out of your speaker and keep it up to date with the latest software.

TROUBLESHOOTING

socket.
The speaker is not responding| A software problem has occurred.| Unplug the mains power plug from the wall socket, wait for 15 seconds, then plug it in again.
There is no audio or the audio is too low| The wrong audio source is selected.| Use the source button to select the audio source.
The audio device is not connected.| Ensure that the device is connected to Woburn III.
Volume is set too low on either the audio source or the speaker.| Slightly increase the volume on your audio source or the speaker.
The audio is distorted| The volume is set too high on the audio source.| Turn down the playback volume on the audio source.
| The volume, bass, or treble is set too high on the speaker.| Lower the volume, bass, or treble on the speaker.
Cannot connect or pair with a Bluetooth device| Bluetooth is not enabled on your device
(smartphone, tablet, computer).| Activate Bluetooth on your audio device.
A Bluetooth device is already connected to the speaker.| Disconnect the connected Bluetooth audio device before setting the speaker in pairing mode.
The speaker is not in pairing mode.| I. Use the source button to select Bluetooth.
II. Push the source button until the Bluetooth LED pulses red.
Bluetooth connection drops out| The two Bluetooth devices are too far apart, or the connection is affected due to obstacles.| Move the devices closer to each other so that they are unobstructed by obstacles such as walls or doors.
Bluetooth connection
drops out| There is a strong electric field surrounding the speaker. Items such as microwave ovens, wireless network adapters, fluorescent lights, and gas cookers use the same frequency range as the Bluetooth device. This may lead to electrical disturbances.| Move the speaker to another spot or turn off or move the interfering electronic device.
Erratic behavior| The speaker is not using the latest firmware version.| Download the Marshall Bluetooth app and connect to the speaker.
Follow the in-app instructions to ensure that the speaker has the latest firmware version.
There is a software error.| Perform a factory reset by pressing the media control for more than 10 seconds. The speaker needs to be set up again, see the GETTING STARTED instructions.

MARSHALLHEADPHONES.COM
Design of device and packaging are intellectual properties of Zound Industries International AB and Marshall Amplification Plc.
© All Rights Reserved. MARSHALL, Marshall  Amps, their respective logos, “Marshall” and “Marshall” trade dress are trademarks and intellectual property of Marshall Amplification Plc and may not be used without permission. Permission granted to Zound Industries International AB. The Bluetooth® wordmark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Zound Industries International AB is under license. Google Play is a trademark of Google LLC. App Store is a service mark of Apple Inc., registered in the U.S. and other countries. R 0.11

References

• Marshall — 60 years of loud | Marshall.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>