VIOFO A119 Mini Single Channel 5GHz WiFi GPS Dash Cam User Manual

VIOFO A119 Mini Single Channel 5GHz WiFi GPS Dash Cam

Product Overview

Standard Items

Note: The USB data cable is only for connecting the camera with the computer to transfer video files or upgrade firmware, not for charging the camera

Optional Accessory

Product Diagram

1. Menu / Power On|Off

2. Menu Up / Recording Start / Stop

3. Menu Confirm / Video Protect / Playback

4. Menu Down / Microphone Enable / Disable

5. Wi-Fi On|Off

6. Power in / MicroSD Card Reader Mode

7. Memory Card Slot

8. Reset Button

9. Power Status Indicator

10. Recording Status Indicator

11. Microphone Status Indicator

12. Wi-Fi Status Indicator

Inserting / Removing the Memory Card

Inserting the memory card

Push the memory card into the card slot until you hear a click, with the card label facing forward (away from the screen).

Removing the memory card

Ensure that the camera is turned off / not recording, and then push the edge of the memory card with your fingernail. The card will spring out far enough to be removed.

Note:

The MicroSD card is sold separately. The microSD card must have a Class-10 or UHS-I rating and the capacity is up to 256GB. 64GB,128GB and 256GB microSD cards must be formatted with the FAT32 file system, either on a computer or in the camera. We recommend you buy the VIOFO brand memory card which are manufactured with top-tier MLC NAND flash, making them durable and reliable.

Formatting the card

The memory card must be formatted before first use. We suggest formatting the card periodically to ensure the best performance of the camera.
Note: Formatting card will erase all data permanently, please back up important data beforehand.

LED Indicators

PWR

| Flashing Red| Updating Firmware
Solid Red| Power On
Off| Power Off

REC

| Flashing Red| Not Recording
Solid Red| Recording

MIC

| Solid Blue| Microphone Enabled
Off| Microphone Disabled

Wi-Fi

| Flashing Blue| Wi-Fi Enabled and waiting connecting
Solid Blue| Wi-Fi Connected
Off| Wi-Fi Disabled

Buttons and Icons

Display Overview

Installation

• Insert the clips, then slide the mount horizontally into the slot on the back of camera

• Select a location on the windshield behind the rear-view mirror.

• Wipe clean the installation surface of the windscreen with a dry cloth, it must be grease free for the sticky pad to stick firmly.

• Peel the protection film off the sticky pad and camera lens.

• Fix the dashcam on the selected location.

• Adjust the lens angle

  • Look at the live view on the LCD.
  • Adjust the angle of the lens up / down if necessary

Connecting to Power

Plug the USB power adapter into your vehicle’s 12V / 24V female power socket. Insert the USB cable male port into the camera’s mount USB port

Tips

1. Do not install/mount the camera in a location that interferes with the driver’s visibility and safety.
2. Install/mount the camera close to the rearview mirror so that both sides of the scene being recorded are equally covered by the camera’s FOV (field of view).
3. To ensure a clear view on rainy days, the lens should be positioned within the windshield wiper’s sweeping range.
4. Do not install/mount the camera on or near airbag panels.
5. Installation/mounting location should not be elected by sun control film (window tint). There should not be any other electronic equipment close to the camera for optimal performance.

Note:

Do not install/mount the camera or cables near an airbag panel or within the airbag’s working range. The manufacturer is not liable for any injury or death caused by the deployment of the airbag.

Operation

Power On/Off

1. When you start the engine, the camera will turn on and begin recording automatically.
2. When you turn off the engine or unplug the charging cable from the power adapter, the camera will stop recording and turn off.
3. Long press [ ] button to power on or off the camera.

Loop Recording

1. Insert a microSD card into the camera’s card slot and automatic loop recording will begin once the camera detects power.
2. Time frame for each video file is 1 / 2 / 3 / 5 / 10 minutes.
3. When there is insufficient space on the microSD card, loop recording. will automatically overwrite the oldest files (one by one).
4. Loop recording files are saved to SD card: \DCIM\Movie.

Emergency Recording

1. Automatic emergency recording When the G-sensor is activated by a collision, the current footage will be locked automatically to avoid being overwritten by loop recording.
2. Manual emergency recording Pressing the [ ]button during a recording will lock the current file being recorded. Once locked, the file will not be overwritten by the loop recording feature.

Note:

Collision detection sensitivity can be adjusted in settings under the “G-sensor” option. Locked files are saved to SD card: DCIM \ Movie \ RO

Playback Videos

1. Under standby mode (not recording), click the once [ ] button to enter the playlist.
2. Use the arrow buttons [ ] to select the desired video and press the button [ ] to play.
3. Press the [ ] button to exit.

Note:
The default video resolution of the dashcam is 2560 x 1440P 30fps.

PC Mode

1. Connect the camera to a computer by using the included short USB cable.
2. The camera will automatically turn on and “microSD Card Reader Mode” will be displayed on its LCD screen.
3. The computer will detect a “removable disk”.
4. There will be two folders under the DCIM folder: Movie (loop recording video files) Contains subfolder: Parking (Parking mode video files) RO (Protected / Locked video files) Photo (Video snapshot files)
5. Copy the files needed to your computer drive.

Firmware Upgrade

Follow the instructions on this website to upgrade the firmware: https://viofo.com/en/content/42-help-and-support/

Note:

• Before using a microSD card to upgrade the firmware, formatting the card in camera is necessary to ensure stable read and write operation.
• Do not unplug or power o the camera during a firmware upgrade, it may cause the camera to subsequently fail to boot.

System Settings

Press the Menu button during video mode to access the settings. (recording needs to be stopped)

• Resolution: Set the video resolution of footage recorded 2560 x 1600 30fps, 2560 x 1440 60fps, 2560 x 1440 30fps 2560 x 1080 60fps, 2560 x 1080 30fps, 2304 x 1296 30fps 1920 x 1080 60fps, 1920 x 1080 30fps, are available for selection.
• Bitrate: You can set the bitrate for video. High bitrate may improve the quality and smoothness of the video, especially when recording fast motion or high contrast scenes. Using high bitrate mode may decrease the amount of recording time available on your memory card. Using a low bitrate will save space and record for a longer time.
• Loop Recording: Off / 1/2/3/5/10 minutes.
• WDR: Automatically balance the lighting over bright and over dark areas.
• Exposure: Adjust the value of the EV (Exposure Value) to obtain Automatically balance the lighting over bright and over dark areas. from -2.0 to + 2.0. The default is set at 0.0.
• Parking Mode: There are 3 options under parking mode:

1. Auto event detection: The camera will automatically record for 45 minutes while a moving object is detected during parking. And it will stop recording if there are no new movements.
2. Time-lapse recording: Time-lapse record a video at low frames at 1 / 2 / 3 / 5 / 10 fps, It keeps recording continuously without audio recorded.
3. Low bitrate recording: This mode records video continuously at a low bitrate of 4MB/s in mini file size with audio recorded.

Note: We recommend buying VIOFO HK4 ACC hardwire kit cable for parking mode recording.

• Enter Parking Mode Timer: Parking Recording Duration. parking mode.
• Parking Recording Duration: Set the Parking Recording Duration.
• Parking G-sensor: The G-sensor detects significant or sudden movement (such as an impact or collision), it will trigger an event recording. We suggest setting it to High sensitivity in parking mode recording.
• Parking Motion Detection: Adjust the sensitivity of the motion detection so minor motion caused by wind or rain doesn’t trigger a recording while in parking mode.
• Time-lapse Recording: Record video from frames captured at specific time intervals to conserve memory and reduce the time it takes to review video. The default is off.
• Motion Detection: When this feature is activated, a recording will begin if there is movement in front of the camera. Once the camera does not detect movement for 60 seconds, the recording will be stopped and the device will switch to detect mode. The device will record again if it will detect a new movement in front of the camera.
• GPS: Turns on / off GPS tracking. If disabled, your camera will no longer measure your speed and position nor synchronize the time/date with the atomic clock. (only available when connecting with GPS signal) Please use ” Dashcam Viewer ” to playback videos and to visualize your position and speed on your computer.
• Speed Unit: Set the speed unit, kilometer per hour (KPH) or miles per hour (MPH).
• G-sensor: The G-sensor measures g-shock forces. The setting from ‘Low’ to’ High’ determines the amount of force needed to lock the file from being overwritten by loop-recording. We recommend leaving it set to ‘Low’.
• WiFi: Set it On /Off. Press the [ ]button for 3 or 5 seconds to enable Wi-Fi quickly. We recommend choosing 5GHz Wi-Fi mode. if your mobile phone support 5GHz Wi-Fi.
• Date Stamp: Imprint the time and date on the recorded video.
• GPS Info Stamp: Imprint the GPS information on the recorded video.
• Camera Model Stamp: Imprint the camera model on the recorded video.
• Record Audio: Turn the microphone ON /OFF. This can be also activated by pressing the [ E] button while the camera is recording.
• Screen Saver: Turn the screen OFF after a set time.
• Boot Delay: The camera will boot seconds later when powered on. The settings are Off / 5s/10s.
• LED: Turn the LED light ON/OFF. Date Time: System date/ time setting.
• Time Zone: Set the current time zone for GPS time and date calibration. Note: the time zone must be manually adjusted for daylight savings.
• Language: Display language setting (English, Traditional Chinese, French, etc).
• Voice Notification: Turn on/ off the voice notification.
• Beep Sound: Turn all notification sounds ON/OFF.
• Frequency: Frequency adjustment setting to minimize flickering and banding in recorded video.
• Image Rotation: Turn the screen upside down.
• Image Mirror: Reverse the image from left to right.
• Format: The operation will delete all data on the Micro SD card. Note: Once you format the Micro SD card, all information will be deleted and cannot be restored. Make sure you back up all important files before proceeding.
• Format Warning: Set the number of days between format warnings.
• Default Setting: Restore camera to factory defaults.
• Car Number: Imprint a customized set of 11 digits to the recorded video. Useful to add license plates or identifying features. Custom Text Stamp: Imprint the customized text on the recorded video.
• Firmware Version: Current firmware version check.

Review and Control on Smartphone

The VIOFO app allows you to control your camera remotely by using a smartphone. Features include full camera control, live preview, playback, and video recording. With Wi-Fi enabled, the camera can be only controlled by the VIOFO app. Turn on the Wi-Fi in the menu or long-press the [ ] button. When the Wi-Fi is on, a Wi-Fi status icon and the password appear on the camera LCD screen.

Connecting the camera to a smartphone

• Search “VIOFO” on the Google play store on an Android device or the Apple app store on an iOS device, or scan the below code to download the APP.

• Download and install VIOFO APP.

• Run VIOFO APP.

• Turn on the Wi-Fi in the menu or long-press the [ ] button.

• On the VIOFO app, follow app instructions to connect with the camera.

Bluetooth Remote Control

With the Bluetooth remote control (optional) mounted in a convenient location on your dashboard, you can safely protect important videos from being overwritten, without needing to take your eyes off the road. When you press the bluetooth remote, the camera will lock the current video file and take a video snapshot.

Pairing with a dash camera

• Power on the camera.
• Press and hold the video lock button on the remote control for 3 seconds to pair it with the camera.
• If get paired successfully, the LED indicator of the remote turns blue.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help

Caution

Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. this device must accept any interference received, including interference that may cause undesired operation.

Shenzhen VIOFO Technology Co.,Ltd, declares that this Radio Frequency peripheral is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Customer Service

Thanks for choosing VIOFO! From the date of purchase on, all products are warranted for 12 months and all accessories are warranted for 3 months. VIOFO offers lifetime technical support for all our users. We are committed to making sure that you are 100% satisfied with our products and services.

Product Registration Program

VIOFO also has a Product Registration Program to help customers extend the warranty by 6 months. Visit www.viofo.com and register your new product to extend the warranty from 12 months to 18 months

Your Opinion Matters

If you have any thoughts on how we can do even better, connect with us today at support@viofo.com

Video Sharing

Share videos caught on the VIOFO camera with us. Let’s enjoy your newfound together! Gain a chance to get a mysterious gift at marketing@viofo.com.

How to Contact Us?

• Submit a ticket at support.viofo.com
• Live chat box at www.viofo.com
• support@viofo.com
• www.facebook.com/viofo.world
• +86 755 8526 8909 (CN)
• Mon-Fri 9am-6pm

IC Caution:
This device complies with Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

To maintain compliance with RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

References

• Support : VIOFO Support Center
• VIOFO Dash Cams | Best Video Quality Dash Cam | 4K Dash Cameras
• Support : VIOFO Support Center
• help-and-support

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>