sigel GL140 Artverum Magnetic Glass Board Instruction Manual

June 5, 2024
sigel

sigel GL140 Artverum Magnetic Glass Board Instruction Manual
sigel GL140 Artverum Magnetic Glass Board

Congratulations! The Artverum magnetic glass board is an excellent choice. The Artverum magnetic glass board can also be written on, and is the perfect setting for your ideas, as well as being a designer piece for the wall in offices & businesses, in the home or in catering establishments. An Artverum board is the ideal place to collect and clearly visualise notes, ideas and to- dos. Attach them with a magnet or jot them down with a marker pen. Artverum stands out from the rest with simple, straight lines and high-quality safety glass, and is mounted without a frame for a free-floating 3D look.

SAFETY & GUARANTEE

SIGEL’S ARTVERUM MAGNETIC GLASS BOARDS GUARANTEE THE HIGHEST LEVEL OF SAFETY!

  • TÜV-approved safety mountings without frames hold the boards securely to the wall

  • TÜV- and GS-approved product safety
    GUARANTEE Instructions

  • High-quality tempered glass / safety glass (EN 12150-1)

SUPERB BRAND QUALITY – 25-YEAR GUARANTEE FOR THE GLASS SURFACE!
Guarantee Instruction

  • Guarantee that the glass surface will remain perfect to write on and easy to clean – no smudges or residue – when using SIGEL glass magnetic board accessories.*
  • The guarantee does not apply in cases of mistreatment, negligence, incorrect usage or other methods of utilisation that do not comply with the enclosed instructions.
  • For the terms of our manufacturer‘s guarantee, visit www.sigeloffice.com/en-gb/guarantee

MOUNTING INSTRUCTIONS

  1. Magnetic Glass Board
    Package Contents

  2. Anchors

  3. Screws

  4. Wall fixings

  5. Mounting fittings on the board
    Package Contents

The enclosed anchors and screws are suitable for solid walls only. For all other walls, please use special anchors and screws.

STORING THIS USER GUIDE

This user guide will help you to make the best use of your new magnetic glass board. In addition to this, it contains important information about how to safely mount and use your magnetic glass board.
Read this user guide and make sure you have understood it before mounting and using your new magnetic glass board.
Store this user guide near your magnetic glass board. If the magnetic glass board is passed on to another user, make sure that person also receives this user guide.

SAFETY PRECAUTIONS

The Artverum Magnetic Glass Board is made of tempered safety glass tested to EN 12150-1.

  1. Before mounting, check that there are no service pipes, e.g. for electricity, gas or water, in that part of the wall.
  2. When mounting the magnetic glass board, please ensure that it does not come into contact with sharp objects or hard surfaces such as stone or tiles. We cannot accept any claims for resulting damage to the board. Place the board on a soft surface until it is ready to be mounted and do not remove the protective corners until it is attached to the wall.
  3. The magnetic glass board should only be mounted on an even, solid wall.
  4. In order to mount our magnetic glass boards correctly, we recommend using the enclosed drilling templates. You will find the measurements for the relevant distances between drill holes on page 16 and on our website at www.sigel-office.com/en-gb/mounting-instructions SIGEL GmbH does not assume any responsibility or guarantee for boards that have been incorrectly mounted or for any resulting damage.
MOUNTING
  1. The magnetic glass board can be mounted in portrait or landscape format. The enclosed drilling templates make it simple to mark the position of the drill holes. The wall fixings 4 are screwed securely to the wall using anchors 2 and screws 3. The side of the board with the SIGEL logo should be facing outwards (fig. I).
    MOUNTING INSTRUCTIONS
    Tip: Please use a spirit level to check that the wall fixings 4 are lined up straight.
    The wall fixings 4 have an oblong hole that can be used to adjust their position if necessary. To do so, loosen the screw and move the wall fixings 4 vertically or horizontally as required. Then tighten the screw again.

  2. The magnetic glass board 1 is then mounted onto the wall fixings 4 (Fig. II).
    There are two mounting fittings 5 on the back of the board for this. Each mounting fitting 5 has two openings (Fig. III); the wall fixings 4 must always be slotted into the top opening rather than the side opening, whether the board is hung in portrait or landscape format. Place the mounting fittings 5 on the back of the board over the wall fixings 4 so that the wall fixings 4 are in the centre (Fig. III). Now slide the board downwards so that the wall fixings 4 click into the mounting fittings 5 (Fig. IV) and the board is mounted securely. Make sure that the magnetic glass board is always mounted on two fittings and check that the board is securely in place before letting go. Silicon pads on the back of the board keep it steady while it is being written on.
    MOUNTING INSTRUCTIONS
    MOUNTING INSTRUCTIONS
    MOUNTING INSTRUCTIONS
    MOUNTING INSTRUCTIONS
    MOUNTING INSTRUCTIONS

  3. MOUNTING SEVERAL BOARDS IN A ROW
    Please note the following if mounting several boards next to each other:
    Due to the fragile glass edges, the magnetic glass boards should not be mounted right next to each other. There should be a gap of at least 3 mm between the individual boards. When mounting the boards, make sure the edges do not knock against each other, as this can cause the board to break. SIGEL is not liable for any damage caused in this way. Do not remove the protective corners until the mounting process is complete.

Mount the first magnetic glass board as described under “Mounting” before marking the drill holes for the next board. This will allow you to adjust the position of the additional boards to any slight inaccuracies there may be in the position of the first board.

USE & CLEANING

The glass surface should be written on using only special markers for glass. The magnetic glass board can be cleaned with a damp or dry cloth. Please do not use abrasive scouring agents, detergents or chemicals to clean the board. To prolong the life of your board, we recommend using our own SIGEL accessories.

GUARANTEE

  • We offer a 25-year guarantee that the glass surface will remain perfect to write on and to clean. We guarantee that the magnetic glass board will remain easy to wipe and free of smudges and other residue when using SIGEL accessories and following our instructions for use. This guarantee does not apply in cases of mistreatment, negligence, incorrect usage or other methods of utilisation that do not comply with the enclosed instructions.

MAGNETS

  • Due to the thickness of the glass, only the enclosed SuperDym neodymium magnets or other extra-strong magnets can be used.

  • If the distance between them is too small (< 10 cm), the magnets can collide, causing the magnetic coating to chip or the magnets to splinter.
    Icon

  • Danger of injury: fingers or skin can be squashed between two magnets, resulting in bruising.

  • Magnets create a strong, far-reaching magnetic field. There is a risk of damage to cards with a magnetic strip, electronic appliances (data carriers, mobile phones, computer, monitors, etc.), mechanical watches and hearing aids.
    Icon

  • People with pacemakers and heart defibrillator implants should avoid magnetic fields.

  • Magnets are not a toy! Keep them out of the reach of children – small parts are a choking hazard.

DISPOSAL AND RECYCLING

When your magnetic glass board has reached the end of its life cycle, ensure that you dispose of it safely and correctly after disassembly. The magnetic glass board and its packaging should be disposed of in compliance with local waste disposal regulations and environmental laws. Dispose of recyclable materials properly and in an environmentally friendly way. The packaging is made of plastic and cardboard, and should be recycled separately. For further information about waste disposal, contact your local authority.

DISTANCE BETWEEN DRILL HOLES

  • Board | 30 x 30 cm
    DISTANCE BETWEEN DRILL HOLES

  • Board | 60 x 40 cm
    DISTANCE BETWEEN DRILL HOLES

  • Board | 48 x 48 cm
    DISTANCE BETWEEN DRILL HOLES

  • Board | 91 x 46 cm
    DISTANCE BETWEEN DRILL HOLES

  • Board | 78 x 48 cm
    DISTANCE BETWEEN DRILL HOLES

  • Board | 100 x 65 cm
    DISTANCE BETWEEN DRILL HOLES

  • Board | 12 x 78 cm
    DISTANCE BETWEEN DRILL HOLES

Measurements from centre of one drill hole to the other Distance

QR Code:
QR Code

Contact Us

SIGEL GmbH
Bäumenheimer Str. 10
86690 Mertingen
Deutschland
Telefon +49 90 78 81-0
kontakt@sigel.de
www.sigel-office.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals