Sublue Paddleboard Power Conversion Kit User Manual

Paddleboard Power Conversion Kit
User Manual

Please read this User Manual carefully before operation and keep it properly.

• This product is not intended for use by people under the age of eight.
• As with other electronic products, care should be taken to prevent the risk of electric shock during use.

Recommendations and Support

1 Recommendation

When using this product for the first time, please read the “Paddleboard Power Conversion Kit User Manual” for product information and instructions.

Support

You can choose the following ways to get related service and support for frequently asked questions (FAQ), user manual, and teaching videos, etc.
Website: http://www.sublue.com
Email: [email protected]

Service hot line: 400-806-2688
Email: [email protected]
Working time: Monday to Friday,
9:00 to 18:00 (Beijing time)

United States:
Other regions:
Please contact your dealer for support.
Information on regional general agents

Safety Information

Warning!

1. This product cannot be used as a life-saving appliance.
2. Be sure to read the User’s Manual carefully before using this product, and be familiar with all operating methods and precautions.
3. Please ensure that there is a companion caring for you within a certain distance during use of the product.
4. This product is not intended for young persons under the age of eight.
5. Before using, the product should be fully inspected to confirm that the battery is in good condition and the power capacity is sufficient. And confirm that the propellers and thrusters are running and functioning normally.
6. Before using the product, you should fully understand the water area you want to enter. Ensure that you are swimming and diving in the appropriate water area with the water area management authority.
7. Always pay attention to the surrounding water area during use to ensure that there is no danger of collision between boats and swimmers.
8. To ensure safety, users shall be either wearing life jackets or equipped with life-saving equipment under any circumstances.
9. Always remove the battery from the product before transporting or carrying the product by air, and store the battery separately in accordance with relevant regulations.
10. Do not put your fingers into the propeller. Do not attach clothing or other objects near the propeller.
11. Do not wear loose clothing or devices that are easily sucked into the propeller by water.
12. Wear a swimming hat when using this product, and pay attention to people with long hair to avoid twisting hair or clothing into the propeller.
13.  When using this product, always pay attention to the battery power and make sure to return before battery exhaustion.
14. Don’t let your face or mask against the rear of the propeller.

Notice

• Please fully charge the batteries of the power system and the control handle.

• Do not take alcohol or medication before or during using this product.

• Try to use this product in an open area. To avoid danger, don’t let clothes, algae, ropes, shark prevention nets, shells, sand or other debris in the water be twisted into the propeller.

• Do not replace the battery in water, replace the battery in a dry environment, and ensure that the device and hands are dry.

• To protect the service life of the motor, don’t run it continuously for more than the 30S in air. If there is an abnormal state (such as the smell of burning), release the switch
  immediately to stop the machine and cut off the power supply at once.

• Do not try this product directly on the beach to avoid sand, shells or other debris getting into the propeller.

• The surface of the product should not be in contact with volatile or acidic substances such as gasoline or rubber water, or sharp objects.

• Do not place heavy objects on the product.

• Do not throw the battery into fire. When the product is not in use, please prevent it from direct sunlight. High temperatures can damage the battery and can cause an explosion or leakage.

• Do not use this product beyond its specified limit depth (5m).

• There should be adequate lighting when diving in dark waters or at night.

• This product is not intended for use in water areas with mixed sand or similar physical properties.

• Don’t use it when the machine malfunctions.

• When not using this product, be sure to take it out of the water.

• Non-manufacturer after-sales service person must not repair without authorization.

• Improper repair may result in water leakage, damage, fire, or electric shock.

• If several users are using the products at the same time, for the sake of safety, ensure the distance between each other is more than 1m.

• Please read the User Manual and precautions carefully before using this product!

Product Overview

The Paddleboard Power Conversion Kit is a brand-new assistance product launched by Sublue for diving, swimming, and water enthusiasts worldwide. It has three speeds and can be freely switched between fast and slow speeds, realizing an all-around upgrade of power, performance, and experience. The Paddleboard Power Conversion Kit adopts Sublue’s self-developed high- efficiency power system and wireless control technology, innovatively completes the modular design, realizes the flexible assembly of components, is convenient to carry, and meets the diversified needs of single-push and dual- push assistance.

Product Features

Modular design
The modular design is easy to disassemble, carry and store.
Wireless connection
Wireless control is provided, with diverse play methods and unlimited possibilities.
Three-level speed change
The high and low speeds can be switched at any time by the handle.

Multi-machine combination
The single handle can control up to two power systems, realizing more DIY possibilities.
The above-mentioned accessories need to be purchased separately. Please contact Sublue or Sublue’s dealer if necessary.

List of Items

Power system ×1
Control handle ×1
Power system bracket ×1
Quick-release screws ×9
Magnetic charging cable ×2

Before using this product, please check carefully whether the product package includes the above items. If there is any item lost, please contact Sublue or your dealer.
Please check if the product is damaged.
This product package does not contain accessories other than those mentioned above. Other accessories can be purchased separately from Sublue.

Components Name

Power System

1. Tini Thruster
2. Power Button
3. Networking Button
4. Speed Control and Battery Indicator
5. Network Indicator
6. Mounting Brackets
7.  Charging Port

Control Handle

1.  Start button
2. Power Button
3. Networking Button
4. Battery Indicator
5. Network Indicator
6. Charging Port

Preparation before the First Use

1 Unpacking for Inspection
Check appearance
After unpacking the equipment, please carefully check whether there are any problems such as cracks in the body shell, falling off of the protective cover, and abrasion of the appearance.
Check functions

1. Check whether the power system can be started and networked normally*, start the thruster after networking, and check whether the propeller is running normally;
2. Check whether the control handle can be started and networked normally*, press the start button after networking, check whether the start button is stuck, whether it can normally control the starting and shutdown of the power system’s propeller, and check whether the speed levels can be switched normally.
   For the operation method, please refer to the relevant content in the following instructions.

If you find any problems when unpacking, don’t use it, and please contact Sublue After-sale Service Center or its authorized service center. Do not run the product for more than 30 seconds without water.

The control handle and power system charging

The control handle and power system are embedded with a magnetic charging head, which can be charged with the magnetic charging cable provided by Sublue. Please use an adapter with a charging voltage of 5V and an output current of 1A and above.

3. Read the User Manual
Before using, please carefully read the user manual and be familiar with the product operation and instructions.

Start Use

Explore the underwater world with your Paddleboard Power Conversion Kit.
Before using the product, please be familiar with the product performance in an absolutely safe water environment and fully master the operations.

Instructions for Assembly

Assembly of Power System and Handle Bracket

1. Install the control handle on the oar with a strap.
2. Install the paddle board bracket and power system on the back of the paddle board by sticking the hanging buckle、

Operation Description

is “low speed” by default.
Pairing button (handle)| Short press for Bluetooth pairing, short press again to exit pairing|
 Start button (handle)| Pull the trigger, press to start, release to pause|
Speed control and battery indicator(handle)| Three gears (1-2-3) speed adjustment respectively green, blue, and red, flashing under low battery (the color is the same as the current gear), red light flashing when charging|
Network indicator (handle)| After power on, the slow flashing is in the direct connection mode, the fast flashing is in the pairing mode, and the steady blue indicates a stable Bluetooth connection.|
Switch button (power system)| Long press (3s) to turn on, when it is turned on, long press (3s) to turn off|
Network button (power system)| Tap to start 125K networking, and tap again to exit 125K networking.|
Low battery indicator (power system)| Low battery LED flashes (the color is the same as the current gear), the red light flashes when charging|
Bluetooth networking indicator (power system)| It is always blue after power on, the LED flashes blue during Bluetooth pairing, and returns to normal blue after Bluetooth pairing is completed. When Bluetooth is disconnected, it flashes blue.|
125K networking indicator light
(power system)| After power on, the indicator light flashes green during 125K pairing. After the 125K pairing is completed, the indicator light flashes green. After exiting 125K
Pairing, the indicator light is green.|

1. When the product leaves the factory, the power system, and the control handle have been networked, so the product can be used directly, and there is no need to carry out networking operations;
2. The control handle and the power system can be turned on and operated independently, so there is a possibility that the speed level display is inconsistent after being turned on. At this time, the speed level of the control handle shall prevail, and except for starting the networking mode, the control handle can perform any operation to change the speed level of the power system to be consistent with that of the control handle.

The control handle contains a built-in lithium polymer battery with a capacity of 1150mAh, which can meet the needs of the control handle service time.

The control handle is embedded with a magnetic charging connector, which can be charged with a Sublue magnetic cable. .
To charge the control handle, an adapter with an output voltage of 5V and an output current of 1A and above is required.
Storage and Maintenance of the Power System Battery and the Control Handle.

1. The battery or control handle shall be stored at 25±5 ° C, the humidity is 65 ± 20% RH, and the battery power is maintained at 30% – 60%. It shall be separately placed in a cool and ventilated place.
2. Do not place the battery or control handle in direct sunlight or in high-temperature places (such as near microwave ovens, ovens, etc.). Overheating of the battery may cause fire or explosion.
3. Do not throw the battery or the control handle into the fire source, otherwise, it may cause the battery to catch fire or explode.
4. Do not charge the battery or control the handle under fire or heat conditions.
5. Do not drop, squeeze or puncture the battery, otherwise, it may cause battery leakage, fire or explosion.
6. Please do not charge the battery or the control handle below 0°C.
7. When the battery or the control handle is used below 0°C, the battery power will be drastically reduced and the running time will be drastically reduced.
8. For safety reasons, the battery or control handle should be kept low during transportation. Please discharge before transportation and place the battery at 30%.
9. For long-term storage, please check the battery level at least once every 6 months and charge the battery to 60%

Maintenance

Cleaning after Use

①Paddleboard Power Conversion
① After each use, Paddleboard Power Conversion Kit should be completely immersed in clear water for 30 minutes to avoid seawater or foreign objects. And pay attention to the following:

• Install the battery and start the power system before cleaning.

• Please use clean water.

• Immerse in water for more than 20 minutes

• Don’t add chemical cleaning products such as laundry detergents or cleaning agents to clean water.

• When Paddleboard Power Conversion Kit is immersed in water, some bubbles are expelled from the holes of the equipment body, which is not a malfunction.
  ② Start the control handle and press the start button to make Paddleboard Power Conversion Kit run in half air and half water for 10 seconds, and repeat this operation
  5-10 times.
  *Paddleboard Power Conversion Kit

• To prevent the water from being splashed on your body during operation, please push the propeller outlet to the bottom of the container.

• Paddleboard Power Conversion Kit has a large thrust force in the water. Don’t dismantle the handle bracket. Please apply the low speed and slightly raise the equipment out of the water surface for cleaning, which is easier to control.
  ③ Shake fully and clean the Paddleboard Power Conversion Kit body to remove any foreign objects attached to it.
  ④ Wipe the surface with a clean, soft, dust-free cloth. Make sure that the product body and battery have no water beads. And place them in a cool and dryplace to dry naturally.

• Never use a hair dryer or drying apparatus.

Storage

If you are not going to use the product for a long time, please note that the power system, control handle, and battery should be stored separately, and please follow the principles below:

1. Please ensure that the power system is in a cool and ventilated place above 0 °C and below 45 °C.
2. Don’t place it in areas with poor ventilation or humidity above 65%RH
3. Don’t place it in areas exposed to direct sunlight.
4. Keep away from heat, fire sources,s, and children’s reach.
5. Keep away from that equipment that may generate strong magnetic fields.
6. Please take out the product at least once a month and run it for about 10 seconds to avoid the corrosion caused by changes in the storage environment.
7. The control handle contains a lithium battery. For storage method, see the Storage and Maintenance of the Power System Battery and the Control Handle.

General Troubleshooting Method

carry electricity
2.  Check whether the power system and control the handle can be turned on normally, and the indicator is on normally
3）Check whether the power system and control handle can be networked normally, and the speed can
be adjusted
4）Check if the propeller can be rotated
5）Contact Sublue or Sublue authorized service organization
The screw propeller is stuck or rotating abnormally| 1）Remove the battery
2）Check if the propeller can be rotated
3） Check if the propeller is wrapped by a foreign object
4）Perform the requirements of the “Clean after use” section in “Maintenance”
5）Contact Sublue or Sublue authorized service organization
The LED lamp of power system is abnormal| 1)  Check if the battery has power
2) Check if it can be started normally
3) Contact Sublue or Sublue authorized service organization
The LED lamp of the control handle is abnormal| 1)Check if the control handle can be started normally
2)Check if the control handle can be charged normally
3) Contact Sublue or Sublue authorized service organization
contact is dirty| 1）Check for damage around the battery contacts
2）Check the host’s sealing gasket for damage or bumps
3）If the stain is slight, clean it with a dry cloth and try to apply vaseline on the battery contacts.
4）Contact Sublue or Sublue authorized service organization
The speed levels cannot be switched normally| 1)Check whether the power system and control handle can be networked normally
2)Contact Sublue or Sublue authorized service organization
The battery is damaged and swells| Contact Sublue or Sublue authorized service organization
Battery charging is abnormal| Contact Sublue or Sublue authorized service organization
The battery back cover is installed abnormally or cannot be removed| 1)Check if the battery is installed correctly
2)Check if the battery swells
3) Check if the battery compartment cover button can be pressed and rebounded normally
4) Contact Sublue or Sublue authorized service organization

Product Parameters

Specifications and Parameters
Size: Tini power part: L 355mm × W135mm × H 135mm
Control handle: L 95mm × W 57mm × H158mm
Weight: 3000g (including battery)

Power system: The usual use time can reach the highest 45 minutes (Continuous use time³: can reach 20 minutes at high speed, 30 minutes at middle speed， and 35minutes at low speed)
Control handle: The usual use time can reach the highest 150 minutes (Continuous use time4 can reach 100 minutes)
Ambient temperature for operating: 0-35°
Storage environment temperature: 0-45°

1. The speed level is the experimental speed. The speed of navigation will be affected by such factors as different users, water temperature, water depth, and flow, and other
   water conditions, as well as the increase of equipment-carrying load, and the user’s underwater wearing and equipment.

2. The normal use time is the average value of the maximum time that the user operates the product in general usage habits (non-continuous operation) when the equipment is fully charged.

3. The continuous use time of the power system is the average value of the maximum time that the user can achieve for continuous use in each speed level when the product
   is fully charged.

4. The continuous use time of the control handle is the average value of the maximum time that the user can achieve by continuously pressing the start button after the product is started.

Optional Accessories

1. Double-boosting Handle Bracket Get greater thrust force and cruising speed, and enjoy a more exciting experience.
The above accessories do not include the Tini propeller.
※The above accessories need to be purchased separately. Please contact SUBLUE or the designated dealer for details.
Sublue Technical support
http://service.sublue.com
The information, photos and instructions contained in this manual are the property of Sublue and are not allowed to be copied and distributed without authorization. In addition, Sublue reserves the right to change any of the information in this manual.

You can check the latest version of the user manual in the “Service Support” section of the SUBLUE official website.
If you have any questions or suggestions about the user manual, please contact us by the following email address: [email protected]

Warning：
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment has been tested and found to comply with the limits for a Class B  digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To assure continued operation, follow the attached installation instructions and use only shielded cables when connecting to other devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

References

• Sublue

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>