HiKOKI CR13VBY Cordless Reciprocating Saw Instruction Manual

HiKOKI CR13VBY Cordless Reciprocating Saw

GENERAL POWER TOOL SAFETY

WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

   • a) Keep work area clean and well lit.
     Cluttered or dark areas invite accidents.

   • b) Do not operate power tools in explosive atmospheres, such as in the presence of fl ammable liquids, gases or dust.
     Power tools create sparks which may ignite the dust or fumes.

   • c) Keep children and bystanders away while operating a power tool.
     Distractions can cause you to lose control.

2. Electrical safety

   • a) Power tool plugs must match the outlet.
     Never modify the plug in any way.
     Do not use any adapter plugs with earthed (grounded) power tools.
     Unmodifi ed plugs and matching outlets will reduce risk of electric shock.

   • b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
     There is an increased risk of electric shock if your body is earthed or grounded.

   • c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

   • d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
     Damaged or entangled cords increase the risk of electric shock.

   • e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
     Use of a cord suitable for outdoor use reduces the risk of electric shock.

   • f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
     Use of an RCD reduces the risk of electric shock.

3. Personal safety

   • a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the infl uence of drugs, alcohol or medication.
     A moment of inattention while operating power tools may result in serious personal injury.

   • b) Use personal protective equipment. Always wear eye protection.
     Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

   • c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your fi nger on the switch or energising power tools that have the switch on invites accidents.

   • d) Remove any adjusting key or wrench before turning the power tool on.
     A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

   • e) Do not overreach. Keep proper footing and balance at all times.
     This enables better control of the power tool in unexpected situations.

   • f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
     Loose clothes, jewellery or long hair can be caught in moving parts.

   • g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
     Use of dust collection can reduce dust-related hazards.

   • h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
     A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care

   • a) Do not force the power tool. Use the correct power tool for your application.
     The correct power tool will do the job better and safer at the rate for which it was designed.

   • b) Do not use the power tool if the switch does not turn it on and off .
     Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

   • c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

   • d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
     Power tools are dangerous in the hands of untrained users.

   • e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may aff ect the power toolʼs operation.
     If damaged, have the power tool repaired before use.
     Many accidents are caused by poorly maintained power tools.

   • f) Keep cutting tools sharp and clean.
     Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

   • g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
     Use of the power tool for operations different from those intended could result in a hazardous situation.
     h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
     Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Service

6. a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
   This will ensure that the safety of the power tool is maintained.

PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of children and infi rm persons.

RECIPROCATING SAW SAFETY

WARNINGS

1. Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord.
   Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock

2. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the power source to be utilized conforms to the power requirements specifi ed on the product nameplate.

2. Ensure that the power switch is in the OFF position.
   If the plug is connected to a receptacle while the power switch is in the ON position, the power tool will start operating immediately, which could cause a serious accident.

3. When the work area is removed from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as practicable.

4. Prior to cutting into walls, ceilings or floors, ensure there are no electric cables or conduits inside

5. Dust produced in operation
   The dust produced in normal operation may aff ect the operator’s health. To wear a dust mask is recommended.

6. Mounting the blade (Fig. 1)This unit employs a detachable mechanism that enables mounting and removal of saw blades without the use of a wrench or other tools.

   • Turn on and off the switching trigger several times so that the lever can jump out of the front cover completely. Thereafter, turn off the switch and unplug the power cord.
     Be absolutely sure to keep the switch turned off and the power cord unplugged to prevent any accident.

   • Pull the back of the saw blade two or three times by hand and check that the blade is securely mounted. When pulling the blade, you will know it is properly mounted if it clicks and the lever moves slightly.
     When pulling the saw blade, be absolutely sure to pull it from the back. Pulling other parts of the blade will result in an injury.

7. Never touch the saw blade immediately after use. The metal is hot and can easily burn your skin

8. When the blade is broken
   Even when the saw blade is broken and remains inside the small slit of the plunger, it should fall out if you push the lever in the direction of the arrow mark, and face the blade downward. If it doesn’t fall out itself, take it out using the procedures explained below.

9. If a part of the broken saw blade is sticking out of the small slit of the plunger, pull out the protruding part and take the blade out.

10. If the broken saw blade is hidden inside the small slit, hook the broken blade using a tip of another saw blade and take it out.

11. Maintenance and inspection of saw blade mount

    • After use, blow away sawdust, earth, sand, moisture, etc., with air or brush them away with a brush, etc., to ensure that the blade mount can function smoothly.

    • As shown in Fig. 3, carry out lubrication around the blade holder on a periodic basis by use of cutting uid, etc.

    • Continued use of the tool without cleaning and lubricating the area where the saw blade is installed can result in some slack movement of the lever due to accumulated sawdust and chips. Under the circumstances, pull a rubber cap provided on the lever in the direction of an arrow mark as shown in Fig. 3 and remove the rubber cap from the lever. Then, clean up the inside of the blade holder with air and the like and carry out suffi cient lubrication.
      The rubber cap can be fi tted on if it is pressed fi rmly onto the lever. At this time, make certain that there exists no clearance between the blade holder and the rubber cap, and furthermore ensure that the saw-blade-installed area can function smoothly.

    • Do not use any saw blade with a worn-out blade hole (A). Otherwise, the saw blade can come off , resulting in personal injury. (Fig. 4)

12. Adjusting the swing cutting operation

    • Even for soft materials, you should perform straight cutting if you wish to make curved or clean cuts.
    • Dust and dirt accumulated on the change lever section can degrade the function of the change lever. Periodically clean the change lever section.
    • When performing swing cutting, use a saw with straight blade. If a saw with curved blade is used, the saw blade may be broken or the unit may be damaged.

13. How to use

    • Avoid carrying it plugged to the outlet with your fi nger on the switch. A sudden startup can result in an unexpected injury.

    • Be careful not to let sawdust, earth, moisture, etc., enter the inside of the machine through the plunger section during operation. If sawdust and the like accumulate in the plunger section, always clean it before use.

    • Do not remove the front cover. Hold firmly the front cover by hand to operate. But, do not extend your hand or fi nger beyond the fl ange of front cover to avoid an injury.

    • During use, press the base against the material while cutting.
      Vibration can damage the saw blade if the base is not pressed firmly against the workpiece.
      Furthermore, a tip of the saw blade can sometimes contact the inner wall of the pipe, damaging the saw blade.

    • Select a saw blade of the most appropriate length. Ideally, the length protruding from the base of the saw blade after subtracting the stroke quantity should be larger than the material (see Fig. 8). If you cut a large pipe, large block of wood, etc., that exceeds the cutting capacity of a blade; there is a risk that the blade may contact with the inner wall of the pipe, wood, etc., resulting in damage.

    • To maximize cutting eciency for the materials you are using and working conditions, adjust the speed of the saw blade and the switching to swing cutting.
      Cutting

    • Always hold the tool firmly with hand on housing as shown in Fig. 9, Fig. 10 and Fig. 11.

    • Press the base firmly against the workpiece.

    • Never apply any unreasonable force to the saw blade
      when cutting. Doing so can easily break the blade.

    • Fasten a workpiece firmly before operation. (Fig. 9)
      When cutting metallic materials, use proper machine oil (turbine oil, etc.). When not using liquid machine oil, apply grease over the workpiece.

    • The service life of the saw blade will be drastically shortened if you don’t use machine oil.

    • Never apply any unreasonable force to the saw blade when cutting. Also remember to press the base against the lumber firmly.
      Sawing curved lines

    • We recommend that you use the BI-METAL blade mentioned in Table 2 for the saw blade since it is tough and hardly breaks.

    • Delay the feed speed when cutting the material into small circular arcs. An unreasonably fast feed may break the blade.
      Plunge cutting (Fig. 10 and 11

    • Avoid plunge cutting for metallic materials. This can easily damage the blade.

    • Never pull the switch trigger while the tip of the saw blade tip is pressed against the material. If you do so, the blade can easily be damaged when it collides with the material.

    • Make absolutely sure that you cut slowly while holding the body fi rmly. If you apply any unreasonable force to the saw blade during the cutting operation, the blade can easily be damaged.

14. Cut off guide for cutting pipe (optional accessory) Please refer to the cut off guide user’s manual for details on how to use it correctly.

SYMBOLS

WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the accessories listed in the below.

• Blade (No. 341) …………………………………………………….1
• Case …………………………………………………………………..1

Standard accessories are subject to change without notice.

APPLICATIONS

• Cutting pipe and angle steel.
• Cutting various lumbers.
• Cutting mild steel plates, aluminum plates, and copper plates.
• Cutting synthetic resins, such as phenol resin and vinyl chloride.

For details refer to the section entitled “SELECTION O BLADES”.

SPECIFICATIONS

Voltage (by areas) *| (110 V, 115 V, 120 V, 127 V,

220 V, 230 V, 240 V)

---|---
Power Input *| 1150 W

Capacity

| Mild Steel Pipe| O.D. 130 mm
Vinyl Chloride Pipe| O.D. 130 mm
Wood| Depth 300 mm
Mild Steel Plate| Thickness 19 mm
No-Load Speed| 0 – 3000 min–1
Stroke| 32 mm
Weight (without cord) **| 4,6 kg

• Be sure to check the nameplate on product as it is subject to change by areas.
  ** According to EPTA-Procedure 01/2014.

NOTE
Due to HiKOKI’s continuing program of research and development, the specifications herein are subject to change without prior notice.

MOUNTING AND OPERATION

Refer to Table 1, 2, 3 and 4 for use of the blades.

Adjusting the base (Fig. 5)This unit employs a mechanism that can adjust the base mounting position in three stages without the use of a wrench or other tools.

1. Press a pushbutton. When you do this, a base lever will jump out to prepare the base for adjustment.
2. Push up the base tip and jog the base back and forth.
3. You can adjust the base position in three stages. Move the base at an interval of about 15 mm, fi nd the position where the base hooks, and press in the base lever with your fi ngers. The base is secured when you hear the clicking sound.

Adjusting the blade reciprocating speed

This unit has a built-in electronic control circuit that makes it possible to adjust the variable speed of the saw blade either both by pulling a switching trigger or turning a dial. (Fig. 6)

1. If you pull the trigger further in, the speed of the blade accelerates. Begin cutting at a low speed to ensure the accuracy of your target cut position. Once you’ve obtained a suffi cient cutting depth, increase the cutting speed.
2. On the dial scale, “5” is the maximum speed and “1” the minimum. The high speed is generally suitable for soft materials such as wood, and the low speed is suitable for hard materials such as metal. We recommend that you use the following as a rough guide in selecting the suitable speed for the materials you are cutting.
   Example of materials to be cut| Recommended dial scale
   ---|---
   Mild steel pipes / cast-iron tubes /

L-shaped angle steel

| 2 ― 4
Wood / wood with nails driven in| 5
Stainless steel| 1 ― 3
Aluminum / brass / copper| 2 ― 4
Plaster board| 4 ― 5
Plastic / fiber board| 1 ― 3

CAUTION

• When cutting at low speed (scale of 1 – 2), never cut a wooden board more than 10 mm thick or a mild steel plate more than 2 mm thick. The load on the motor can result in overheating and damage.
• Although this unit employs a powerful motor, prolonged use at a low speed will increase the load unduly and may lead to overheating. Properly adjust the saw blade to allow steady, smooth cutting operation, avoiding any unreasonable use such as sudden stops during cutting operation.

SELECTION OF BLADES

To ensure maximum operating efficiency and results, it is very important to select the appropriate blade best suited t the type and thickness of the material to be cut.

NOTE

Dimensions of the workpiece mentioned in the table represent the dimensions when the mounting position of the base is set nearest to the body of the reciprocating saw. Caution must be exercised since dimensions of the workpiece will become smaller if the base is mounted far away from the body of the reciprocating saw.

1. Selection of HCS blades
   The blade number of HCS blades in Table 1 is engraved in the vicinity of the mounting position of each blade. Select appropriate blades by referring to Tables 1 and 4 below
   Table 1: HCS blade
   

2.5 – 6

No. 95| For cutting stainless pipe less than 105 mm in diameter| Below 2.5
No. 96| For cutting stainless pipe less than 30 mm in diameter| Below 2.5

NOTE
No. 1 – No. 96 HCS blades are sold separately as optional accessories.

Selection of BI-METAL blades
The BI-METAL blade numbers in Table 2 are described on the packages of special accessories. Select appropriate blades by referring to Table 2 and 4 below.

Table 2: Bl-METAL blades

NOTE
Nos. 101 – No. 132 Bl-METAL blades are sold separately as optional accessories.
Table 3: Curved blade

Selection of blades for other materials Table 4

2.5 – 19

| No. 1, 2, 101,

102, 103, 104,

105, 106, 131,

 |  |  | 132
 |  | Below 3.5| No. 3, 107,
 |  | 108
Nonferrous| Aluminium,|  | No. 1, 2, 101,
metal| Copper and Brass| 5 – 20| 102, 103, 104,

105, 106, 131

132

 |  | Below 5| No. 3, 107,
 |  | 108
Synthetic| Phenol resin,| 10 – 50| No. 1, 2, 4,
resin| Melamine

resin, etc.

| 101, 102, 103,

104, 131, 132

 |  | 5 – 30| No. 3, 5, 8,
 |  | 105, 106, 107,
 |  | 108
 | Vinyl chloride,| 10 – 60| No. 1, 2, 4,
 | Acrylic resin,| 101, 102, 103,
 | etc.| 104, 131, 132
 |  | 5 – 30| No. 3, 5, 8,
 |  | 105, 106, 107,
 |  | 108

MAINTENANCE AND INSPECTION

1. Inspecting the blad
   Continued use of a dull or damaged blade will result in reduced cutting e ffi ciency and may cause overloading of the motor. Replace the blade with a new one as soon as excessive abrasion is noted.

2. Inspecting the mounting screws
   Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could result in serious hazard

3. Maintenance of the motor
   The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water

4. Inspecting the carbon brushes (Fig. 12)The motor employs carbon brushes which are consumable parts. Since an excessively worn carbon brush can result in motor trouble, replace the carbon brushes with new ones having the same carbon brush No. ⓐ shown in the figure when it becomes worn to or near the “wear limit” ⓑ. In addition, always keep carbon brushes clean and ensue that they slide freely within the brush holders.

5. Replacing carbon brushes (Fig. 12)
   Disassemble the brush caps with a slotted-head screwdriver. The carbon brushes can then be easily removed.

6. Replacing supply cord

CAUTION
In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with statutory/country specifi c regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, undismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a HiKOKI Authorized Service Center.

IMPORTANT
Correct connection of the plug
The wires of the main lead are coloured in accordance with the following code:
Blue: — Neutral
Brown: — Live
As the colours of the wires in the main lead of this tool may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:
The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. Neither core must be connected to the earth terminal.

NOTE
This requirement is provided according to BRITISH STANDARD 2769: 1984.
Therefore, the letter code and colour code may not be applicable to other markets except The United Kingdom.

Information concerning airborne noise and vibration The measured values were determined according to EN62841 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 102 dB (A) Measured A-weighted sound pressure level: 91 dB (A) Uncertainty K: 5 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined according to EN62841.
Cutting boards:
Vibration emission value ah, B = 19.7 m/s2
Uncertainty K = 1.5 m/s2
Cutting wooden beams:
Vibration emission value ah, WB = 24.9 m/s2 Uncertainty K = 1.6 m/s2

The declared vibration total value has been measured in accordance with a standard test method and may be used for comparing one tool with another.
It may also be used in a preliminary assessment of exposure.

WARNING

• The vibration emission during actual use of the power tool can diff er from the declared total value depending in the ways in which the tool is used.
• Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

NOTE
Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to change without prior notice.

GUARANTEE CERTIFICATE

1. Model No.
2. Serial No.
3. Date of Purchase
4. Customer Name and Address
5. Dealer Name and Address
   (Please stamp dealer name and address)

Hikoki Power Tools Deutschland GmbH
Siemensring 34, 47877 willich, Germany
Tel: +49 2154 49930
Fax: +49 2154 499350
URL: http://www.hikoki-powertools.de
Hikoki Power Tools Netherlands B.V.
Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands Tel: +31 30 6084040
Fax: +31 30 6067266
URL: http://www.hikoki-powertools.nl
Hikoki Power Tools (U.K.) Ltd.
Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom
Tel: +44 1908 660663
Fax: +44 1908 606642
URL: http://www.hikoki-powertools.uk
Hikoki Power Tools France S.A.S.
Parc de l’Eglantier 22, rue des Cerisiers, Lisses-C.E. 1541, 91015 EVRY CEDEX, France
Tel: +33 1 69474949
Fax: +33 1 60861416
URL: http://www.hikoki-powertools.fr
Hikoki Power Tools Belgium N.V./S.A.
Koningin Astridlaan 51, B-1780 Wemmel, Belgium
Tel: +32 2 460 1720
Fax: +32 2 460 2542
URL http://www.hikoki-powertools.be
Hikoki Power Tools Italia S.p.A
Via Piave 35, 36077, Altavilla Vicentina (VI), Italy
Tel: +39 0444 548111
Fax: +39 0444 548110
URL: http://www.hikoki-powertools.it
Hikoki Power Tools lbérica, S.A.
C/ Puigbarral, 26-28, Pol. Ind. Can Petit, 08227 Terrassa (Barcelona), Spain
Tel: +34 93 735 6722
Fax: +34 93 735 7442
URL: http://www.hikoki-powertools.es
Hikoki Power Tools Österreich GmbH
IndustrieZentrum NÖ –Süd, Straße 7, Obj. 58/A6 2355 Wiener Neudorf, Austria
Tel: +43 2236 64673/5
Fax: +43 2236 63373
URL: http://www.hikoki-powertools.at
Hikoki Power Tools Norway AS
Kjeller Vest 7, N-2007 Kjeller, Norway
Tel: (+47) 6692 6600
Fax: (+47) 6692 6650
URL: http://www.hikoki-powertools.de
Hikoki Power Tools Sweden AB
Rotebergsvagen 2B SE-192 78 Sollentuna, Sweden
Tel: (+46) 8 598 999 00
Fax: (+46) 8 598 999 40
URL: http://www.hikoki-powertools.se
Hikoki Power Tools Denmark A/S
Lillebaeltsvej 90, 6715 Esbjerg N, Denmark
Tel: (+45) 75 14 32 00
Fax: (+45) 75 14 36 66
URL: http://www.hikoki-powertools.dk
Hikoki Power Tools Finland Oy
Tupalankatu 9, 15680 Lahti, Finland
Tel: (+358) 20 7431 530
Fax: (+358) 20 7431 531
URL: http://www.hikoki-powertools.fi
Hikoki Power Tools Hungary Kft.
1106 Bogáncsvirág u.5-7, Budapest, Hungary
Tel: +36 1 2643433
Fax: +36 1 2643429
URL: http://www.hikoki-powertools.hu
Hikoki Power Tools Polska Sp. z o. o.
ul. Gierdziejewskiego 1
02-495 Warszawa, Poland
Tel: +48 22 863 33 78
Fax: +48 22 863 33 82
URL: http://www.hikoki-narzedzia.pl
Hikoki Power Tools Czech s.r.o.
Modřická 205, 664 48 Moravany, Czech Republic
Tel: +420 547 422 660
Fax: +420 547 213 588
URL: http://www.hikoki-powertools.cz
Hikoki Power Tools Romania S.R.L.
Ring Road, No. 66, Mustang Traco Warehouses, Warehouse No.1, Pantelimon City, 077145, Ilfov County, Romania
Tel: +40 371 135 109
Fax: +40 372 899 765
URL: http://www.hikoki-powertools.ro

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that Reciprocating Saw, identifi ed by type and specifi c identifi cation code 1), is in conformity with all relevant requirements of the directives 2) and standards 3). Technical fi le at 4) – See below.
The European Standard Manager at the representative offi ce in Europe is authorized to compile the technical fi le.
The declaration is applicable to the product affi xed CE marking.

1. CR13V2 C338589S

2. 2006/42/EC, 2014/30/EU, 2011/65/EU

3. EN62841-1:2015
   EN62841-2-11:2016+A1:2020
   EN55014-1:2006+A1:2009+A2:2011
   EN55014-2:1997+A1:2001+A2:2008
   EN61000-3-2:2014
   EN61000-3-3:2013

4. Representative offi ce in Europe

Hikoki Power Tools Deutschland GmbH
Siemensring 34, 47877 Willich, Germany
Head offi ce in Japan
Koki Holdings Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>