Annex Products Pty 2DWC 2-In-1 Magnetic Desktop Wireless Charger User Guide
- June 5, 2024
- Annex Products Pty
Table of Contents
Annex Products Pty 2DWC 2-In-1 Magnetic Desktop Wireless Charger User Guide
MOUNTING ANGLES
FOREIGN OBJECT DETECTION
Remove phone rings or wallets mounted on device as they will interfere with
charging.
CAUTION: Keep fingers clear of hinge
PLUG IT IN
LIGHT SENSOR
will automatically enter LED into Night Mode when the room is dark or the
sensor is covered.
Plug USB cable into an 18W or higher power supply.
NOTE: Some USB-A sockets such as laptop’s and older power bricks may not have sufficient power for this product and may not be able to charge two devices simultaneously.
WARNING! This product contains magnets and components that generate strong electromagnetic fields. Keep your Quad Lock product a safe distance away from any sensitive or implanted medical devices. Consult with your medical practitioner or device manufacturer before use, or if you suspect the product is interfering with your device.
LED LIGHT STATES
|
DAY MODE
| NIGHT MODE
---|---|---
| CHARGER BASE CHARGER HEAD|
CHARGER BASE CHARGER HEAD
NO CHARGING|
|
CHARGING| 
|
LIGHT GOES OFF AFTER 3 SECS
ERROR/ FOREIGN OBJECT DETECTION| 
CONTINUAL FLASHING|
CONTINUAL FLASHING
FCC STATEMENT
Annex Products Pty Ltd, Australia, declares that the products “Dual Desktop
Wireless Charger”, complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The “Dual Desktop Wireless Charger” has been tested and found to
comply with the limits for a Class B device, pursuant to
Part 15 of the FCC Rules and has been assigned FCC ID: 2AOU9-2DWC. These
limits are designed to provide reasonable protection against harmful
interference. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Use only supplied antenna.
CAUTION: Any changes or modifications in construction of these devices which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device was tested for operations. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt- clips, holsters, and similar accessories used by this device should not contain any metallic components. Body worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
This device in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. All essential radio test suites have been carried out. This restriction will be applied to all Member States of European Union.
- The device complies with RF specifications when the device used at 20cm from your body
Declaration of Conformity
Hereby, Annex Products Pty Ltd declares that the product “Dual Desktop
Wireless Charger” is in compliance with Directives 2014/53/ EU & 2011/65/EU.
The full text of the EU declaration of conformity is available at the
following internet address: https://www.quadlock.com.au/compliance
This device was tested for operations. To comply with RF exposure requirements, a minimum separation distance of 20cm must be maintained between the user’s body and the charger, including the antenna. Third party belt- clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
The device is in compliance with the essential requirements and other relevant provisions of the UK Radio Equipment Regulations SI 2017:1206 (as amended). 1. The device complies with RF specifications when the device used at 20cm form your body.
Declaration of Conformity:
Hereby, Annex Products Pty Ltd declares that the product “Dual Desktop
Wireless Charger” is in compliance with the following Directives: Radio
Equipment Regulations 2017, Electrical Equipment (Safety) Regulations 2016 and
The Restriction of the Use of Certain Hazardous Substances in Electrical and
Electrical Equipment 2012. The full text of the UK declaration of conformity
is available at the following internet address:
https://www.quadlock.com.au/compliance
- Radiated H-Field: 4.99 dBμA/m (@10m) (only for EU and UK)
- TX/RX frequency range: 110-148KHz (only for EU and UK)
INDUSTRIES CANADA (IC: 27134-2DWC)
IC Caution:
Radio Standards Specification RSS-Gen, issue 5
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF exposure statement:
The equipment complies with IC Radiation exposure limits set forth for uncontrolled environments. This equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body.
Manufacturer
Name:| Shenzhen Huagon Technology Co., Ltd| E-mail:
Charles-m@huagon.cn
Address:| 306 3 Floor An hongji Xingyao Industrial Park, No.38 Huaxing
Road, Dalang Street, Longhua District, Shenzhen City China 518109| Title:
Product Manager
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>