XBOX FUSION PRO 2 WIRED CONTROLLER User Manual
- June 5, 2024
- XBOX
Table of Contents
- XBOX FUSION PRO 2 WIRED CONTROLLER
- FRONT
- BACK
- ANALOG STICK REPLACEMENT
- PRO PACK INSTALLATION/REMOVAL
- MAPPING PRO PACK PADDLES
- RESETTING THE PRO PACK PADDLES
- 3-WAY TRIGGER LOCK ADJUSTMENT
- SETUP
- TROUBLESHOOTING
- FCC STATEMENT
- WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
XBOX FUSION PRO 2 WIRED CONTROLLER
FRONT
BACK
ANALOG STICK REPLACEMENT
PRO PACK INSTALLATION/REMOVAL
NOTE: Store all unused components in protective case when not in use.
MAPPING PRO PACK PADDLES
NOTE: Repeat for the remaining Pro Pack paddles. Pro Pack paddle assignments will remain in memory even after disconnected.
RESETTING THE PRO PACK PADDLES
3-WAY TRIGGER LOCK ADJUSTMENT
SETUP
- Connect USB cable into available port on Xbox and into USB-C port on controller. If Xbox is OFF, press Xbox Button to power “ON”. The controller’s Power LED will illuminate.
- For player and controller assignment, refer to the Xbox user manual.
- To remove cable, pull gently. Inline release plug is included closer to end of cable that will disconnect when needed.
USING THE SHARE BUTTON
Refer to Xbox documentation for details on functions and features related to
the Share button.
USING THE HEADSET DIAL
Once you plug the 3.5mm jack from your headset into the controller, Dial will
become active and LED will turn red to indicate chat is muted. Press down on
dial to mute/unmute chat. To adjust volume, tap left or right to adjust step
by step, or press and hold left or right to adjust volume to full up or full
down.
NOTE: Audio controls within Xbox Settings will take first priority,
followed by the Headset Dial, and finally any audio or mute controls on your
headset. Refer to your Xbox and headset documentation for additional details.
TROUBLESHOOTING
For latest FAQs, visit PowerA.com/Support/
PROBLEM: Controller will not connect to game console.
SOLUTION: Confirm cable is properly connected to console. Confirm Inline
Release Cable is properly connected.
PROBLEM: Pro Pack paddles are not functioning properly.
SOLUTION: Confirm Pro Pack is securely installed to controller. Confirm
Pro Pack paddles are securely installed. Review “Mapping Pro Pack Paddles”
section above.
PROBLEM: Controller is connected but has no function.
SOLUTION: Confirm you are using the Player #1 controller by checking the
channel indicator on the controller. Confirm your Xbox console is powered ON,
and your TV is set to the proper video input.
For additional troubleshooting, refer to your Xbox user guide.
MOTION WARNING
Playing video games can make your muscles, joints, skin or eyes hurt. Follow
these instructions to avoid problems such as tendinitis, carpal tunnel
syndrome, skin irritation or eyestrain:
Avoid excessive play. Take a 10 to 15 minute break every hour, even if you don’t think you need it. Parents should monitor their children for appropriate play.
- If your hands, wrists, arms or eyes become tired or sore while playing, or if you feel symptoms such as tingling, numbness, burning or stiffness, stop and rest for several hours before playing again.
- If you continue to have any of the above symptoms or other discomfort during or after play, stop playing and see a doctor.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference;
- This device must accept any interference, including interference that may cause undesired operation of the device
CONTACT/SUPPORT
For support with your authentic PowerA accessories, please visit
PowerA.com/Support
MANUFACTURED BY
Bensussen Deutsch & Associates, LLC. (BDA, LLC.) 15525 Woodinville-Redmond Rd.
NE
Woodinville, WA 98072. | BDAINC.com | POWERA.com | Made in China
WARRANTY
2-Year Limited Warranty: Visit PowerA.com/support for details.
AUSTRALIAN WARRANTY STATEMENT
This product comes with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure. If purchased within Australia or New Zealand, this product
comes with a One-year warranty from date of purchase. Defects in the product
must have appeared within One year from date of purchase, in order to claim
the warranty. All warranty claims must be facilitated back through the
retailer of purchase in accordance with the retailer’s return policies and
procedures. Any expenses incurred, as a result of returning the product to the
retailer of purchase are the full responsibility of the consumer.
AU WHOLESALE DISTRIBUTOR
Level 2, 2 Darling Street South Yarra, Australia VIC 3141
bluemouth.com.au | Email:
support@bluemouth.com.au | +61 (3) 9867
2666
DECLARATION OF CONFORMITY
Hereby, Bensussen Deutsch & Associates LLC at 15525 Woodinville-Redmond Road
NE, Woodinville, WA 98072 USA, declares that this wired controller is in
compliance with Directive 2014/30/EU. The full text of the EU Declaration of
Conformity is available at the following internet address:
PowerA.com/compliance
References
- BDA - The Modern Merchandise Agency for Iconic Brands
- bluemouth.com.au
- llc.tm - This is a premium name
- PowerA | PowerA
- PowerA | PowerA
- Declaration of Conformity | PowerA
- Support | PowerA
- Support | PowerA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>