LEXUS 118652 NX T-One Connector Instruction Manual

LEXUS 118652 NX T-One Connector

WARNING

• ALWAYS read and follow all warnings and instructions included with purchase before beginning installation. Keep for future reference.
• DO NOT exceed lower of towing manufacturing rating (including in your vehicle owner’s manual) or specific amperage ratings stated on product.
• ALWAYS read, understand and follow all warnings and instructions printed on tow vehicle’s battery.
• ALWAYS wear safety glasses and use all safety precautions during installation.

TOOLS REQUIRED:

Trim Panel Remover, 10mm Socket or Wrench, Drill (3/32” Drill Bit), Wire Crimpers, Wire Cutters, Philips Head Screwdriver, Test-probe

1. Open rear hatch. Temporarily remove the rear threshold plate, privacy screen, storage covers and floor covering. Open rear door and fold rear seat forward. A

2. Remove the rear cargo hooks using a 10mm socket or wrench on both driver’s and passenger’s side. Partially pull back the felt side panels to expose the vehicle wiring connectors. B

3. On the driver and passenger sides of the vehicle, locate the matching vehicle’s taillight wiring harness connectors to the T-One® T-Connector mating ends. Separate this connector, being careful not to break the locking tabs. All connector surfaces should be clean and free of dirt. c

4. On the driver’s side, insert the T-One® T-Connector end with the yellow wire between the vehicle wiring connectors and lock into place. Be careful to not break any locking tabs.

5. On the Driver’s side, mount the T-One® Connector black box using the double-sided tape provided. Secure the remainder of the T-One® Connector harness with the cable ties provided, to prevent damage or rattling and being careful to avoid any areas that would cut or pinch the wire.

6. Locate a suitable grounding point near the black box such as an existing ground stud or drill a 3/32” hole and secure the white wire using the eyelet and screw provided. Clean dirt and rustproofing from area.
   CAUTION
   Verify what is behind any surface prior to drilling to avoid damage to the vehicle and/or personal injury. Do not drill into any exposed surfaces.

7. Route the connector containing the green wire across the threshold and behind the passenger’s side felt panel to the taillight pocket.

8. On the passenger’s side, insert the T-One® T-Connector end with the green wire, between the vehicle wiring connectors and lock into place. Be careful not to damage the locking tabs and be sure that connectors are fully inserted with locking tabs in place. c

9. Disconnect the vehicle’s Negative (-) battery cable. If not removed, remove the fuse from the yellow fuse holder (provided).  After cutting the fuse holder wire, attach the ring terminal and secure to the vehicle’s Positive (+) battery cable. Connect the other end of the fuse holder to the black 12 ga. wire, using the yellow butt connector (provided). d

10. Beginning from the front of the vehicle, route the black 12 ga. wire rearward along the frame rail avoiding any hot pipes, heat shields, the fuel tank or any other points that may pinch or break the wire. WARNING
    If routing the wire thru a grommet and along the exterior of the vehicle, be careful to avoid any hot pipes, heat shields, the fuel tank or any other points that may pinch or break the wire.

11. Locate the vent on the driver’s side in the rear cargo area. From underneath route through the vent the black 12 ga wire up into the cargo area.
    NOTE
    For ease of installation use a fish wire through the vent to pull the black 12 ga power wire from underneath vehicle. c

12. Connect the other end of the black 12 ga. wire to the black power wire located on the T-Connector’s black box, using the yellow butt connector (provided).

13. Reconnect the vehicle’s Negative (-) battery cable and install the 15 amp fuse into the fuse holder from step 9.
    WARNING
    Read and follow all warnings and cautions printed on the tow vehicle’s battery. All connections must be complete for the T-One® Connector to function properly. Test and verify installation with a test light or trailer once installed. For initial test, reset vehicle electrical system by temporarily removing the key from the ignition.

14. Reinstall the plastic trim panels, threshold, floor covering and other items that may have been removed during installation, being careful not to pinch or cut the wires.
    NOTE
    Store 4-Flat connector in rear cargo area when not in use.
    WARNING
    When 4-Flat connector in use, be careful not to pinch harness in door latch.
    WARNING
    Overloading circuits can cause fires. DO NOT exceed stated product ratings. Read vehicle’s owner’s manual & instruction sheet for additional information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>