Runleader RL-HM027BT Battery Indicator and Hour Meter User Manual
- June 5, 2024
- Runleader
Table of Contents
Battery indicator & Hour meter RL-HMO27BT
Product Dimension
| ITEM NAME | PARAMETERS | ITEM NAME | PARAMETERS |
|---|---|---|---|
| Product model | RL-HMO27BT | Alert RPM setting range | OFF/100-25000 RPM |
| RPM range | 0-25000 RPM | Firing patterns | 1P1R 1P2R 2P1R 3P1R 3P2R 4P1R 5P2R |
6P1R 8P1R 12PIR
RPM accuracy| 10 RPM| External dimensions| 80×39,6x2Omm
RPM refresh TOT/JOB Hours range| 0.5s /1.0/2.0s 0-99999 H| Display window
size(viewable)
Battery type| 38x16mm CR2032 210mAh
Timing accuracy
TOT initial time range| 0-999H59M: 1Min 1000-9999.9H: 0.1H 10000-99999H: 1H
0-99999 H It is only can be reset 1 hour before engine working| Display type
Housing material| LCD ABS
Working times range Clock system| 0-99999 times 24H| Weight Waterproof rate|
68g IP67
SVC hours range| OFF, 5-1000H| Working voltage| DC8-30V
FCC warning:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
RF exposure information: The device has been evaluated to meet general RF
exposure requirements.
Please read and understand the following notices carefully, and correctly install and operate the product before using it. [ Notice
- Please refer to the installation and function instructions in the APP operation manual to avoid damage caused by installation errors.
- This product contains an internal battery and is replaceable; pls ensure the reliability of battery installation.
- Do not pull the wire when using it to avoid falling off or poor contact.
- Please install the product in an appropriate location to avoid this product being hit and prevent damage to the product.
- This product is waterproof to some extent, but can not be used in deep water or long-term immersion in rainwater.
- Please use this product at the specified temperature, the high-temperature environment may cause damage to the product.
[APP Installation] Four ways to download:
|
---|---
https://res.app.elinkthings.com/app/download/app59/index.html?Moresee
Scan the official QR code of “Moresee” with the mobile phone to download and
install.| http://www.run-leader.com
Find the “Moresee” QR code on the official website “DOWNLOAD” to scan, download and install.
[Product Connection] Bluetooth binding method: 1. Turn on the Bluetooth function of the mobile phone, click on the APP to add a device, search for nearby devices, and click on the product pictures after finding it. 2. When the product is turned on, the LCD will display the ” * ” icon and the “PR Ir ” interface, press the “S” or “M” button to confirm, then the LCD has a Bluetooth icon, and the APP will display “Start Using”, click “Start Using” and wait for the Bluetooth connection to succeed.
[Product Installation Instructions] 1. The wiring installation method is as follows:
Notice: a. Check if the product is installed correctly, the RPM interface
displays RPM. When the engine starts, the RPM interface displays the current
RPM, which means the product is installed correctly.
b. Insufficient fixation of the yellow sensing wire will affect the accuracy
of the test data.
c. The product can be used directly, or connected to an external power supply
to work.lt is recommended to connect an external power supply to improve the
internal battery life. [Product Function Settings] Open the APP “Moresee”,
click the ” i ” icon after the product is successfully connected, find the
“Using Help” and click “Using Help” to see the product function manual, and
the user can refer to the manual to set the function.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>