HAVIT HV1491 Onder Pond Light Instruction Manual

HV1491 Onder Pond Light
Instruction Manual

HV1491 Onder Pond Light Instruction Manual

Product Specifications

Dimensions

Important Safety Issues:

• This product must be installed by a qualified electrician according to AS/NZS 3000.
• Ensure all electrical mains are disconnected before any installation.
• Modification of this product will void any warranty.
• Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
• All electrical connections must be watertight, If a watertight connection is not done, the Warranty will be voided.
• Electrical cannot be submerged under water, If the connection is underwater, the Warranty will be voided.
• When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
• All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining).
• All o-rings and seals must be in place correctly to maintain the warranty.
• These instructions may be updated at any time due to product improvements, Please visit the website for the most current installation instructions.

Steps for Installation: HV1491T

1. Make sure that the electrical circuit is free of voltage (master switch off )
2. Place fitting in the desired location using appropriate screws for application
3. Connect the cable
4. Use an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECT TO 240V
5. Strip back cable on both fittings and cable run and twist the positive cable from fitting to positive on the cable run, then connect neutral from fitting to neutral on the cable run.
6. Solder all joins using solder with either a heat gun or butane gas torch.
7. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. (failure to do this step will void the warranty)
8. Heat the heat shrink or crimp the gel cap making sure all connections are covered. Connections cannot be submerged under water, If connections are underwater, the Warranty will be voided.
9. The Colour temperature is preset to 3000k, to change remove the cover from the fitting by removing the screws in front of the fitting and set it aside. Remove the globe from fitting and move the switch on side of the globe to desired color temperature.
10. Reinsert globe by aligning pins of the globe with holes of lamp holder and push down gently.
11. Reattach the cover and insert screws making sure the seals are still in place and tightening to avoid any water penetration.
12. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Steps for Installation: HV1491RGBW

1. Make sure that the electrical circuit is free of voltage (master switch off )

2. Place fitting in the desired location

3. Connect the cable

4. Use an appropriate 12v DC LED Driver and RGBW LED Controller- DO NOT CONNECT LIGHT FITTING DIRECT TO 240V

5. Do this by stripping back the cable on both fitting and cable run and twisting the cable together making sure all colors are correctly joined to the correct color-
   · Black= Positive
   · Red = Red
   · Green = Green
   · Blue = Blue
   · White = White

6. Solder all joins using solder and either a heat gun or butane gas torch.

7. Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.

8. Heat the heat shrink or crimp the gel cap making sure all connections are covered.

9. Connect cable run to RGBW Controller.

10. Connect Controller to 12v DC LED Driver.

11. All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Must be installed by a licensed electrician

Contact Details:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au

https://havit.com.au/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>