arjo Maxi Twin Scale Mobile Patient Lift Instruction Manual
- June 5, 2024
- arjo
Table of Contents
Twin Scale Mobile Patient Lift
Instruction Manual
0086
..with people in mind
© Arjo Hospital Equipment AB 2009
ArjoHuntleigh products are patented or patent pending. Patent information is
available by contacting rjo Hospital Equipment AB.
Our policy is one of continuous development, and we, therefore, reserve the
right to make technical alterations without notice. The content of this
publication may not be copied either whole or in part without the consent of
Arjo Hospital Equipment AB.
Foreword
The equipment must be used in accordance with these safety instructions.
Anyone using the equipment must have read and understood the instructions in
this booklet
If there is anything you are not sure about, ask your ArHuntleigh
representative.
NOTE: Modifications made to the equipment without ArjoHuntleigh’s
expressed consent from ArjoHuntleigh will invalidate the supplier’s product
liability.
Please comply with the maximum capacity of the scale which is stated on the
identification plate on the back of the device.
CAUTION: Don’t overload the scale.
NOTE: Do not touch parts of the lift or the resident during the weighing
procedure, because these are all integral parts of the weighing instrument.
Intended use
The Maxi Twin Scale is intended to be used with the Maxi Twin lift for
weighing hospital or care facility residents by trained staff in accordance
with the guidelines in the operating and Product Care Instructions. It is
intended to be handled only by trained staff, used indoors and in dry
environment. The Maxi Twin Scale is intended to be calibrated, verified, and
sealed by a notified body.
All other uses must be avoided. The useful life of this equipment, unless
otherwise stated, is ten (10) years.
NOTE
Do not store in a wet environment.
Symbol
Means:
Separate electrical and electronic components for recycling in accordance with
the European Directive 2002/96/EG (WEEE)
Before use
Calibration
The scale is calibrated from the factory and ready for use. If the scale needs
to be recalibrated, please contact your ArjoHuntleigh representative for
support. Scales within the EU are sealed and verified and any calibration or
re-verification has to be done by a notified body.
Weighing
Weight is displayed in kg/lbs.
Display and Control function
Description of symbols
| The battery symbol indicates that the battery needs to be changed
---|---
> 0<| Gross value in the accurate zero range (0.25 d)
Net| Net measurement display
PT| Interactive mode (only for authorized personnel)
The scale is operated by means of two push-buttons:
| Push-button(s) | Keypress |
|---|---|
| ON/OFF switch | |
| **** | Gross/net selection or tare and net display |
Weighing
The scale is ready to use about 10 seconds after it is switched on. During
this time, the scale must neither be moved nor loaded.
Switch on/Weighing
| Switch on the scale
---|---
| Display segment test (- 5 seconds) please wait
| Then all segments go off (- 2 seconds) please wait
| Automatic zeroing 1 (- 3 seconds) please wait
****| The scale is ready to use Now you can weigh
Taring
Switch on the scale and wait -10 seconds
| Taring
---|---
| Now you can weigh/weigh by addition
Changing the unit kg /lb (Only applies to non-verifiable scales, USA and
Canada)
Switch on the scale and wait – 10 seconds
| Unit kg
---|---
| Keep pressed for -5 seconds
| Unit Lb (American pound)
The same method is used to change from Lb to kg.
The last unit set is retained even when the scale is switched off.
Weighing methods
Method A.
How to start weighing with the resident already placed in the sling:
- Raise the lift so the sling with the resident is clear of the floor, bed, etc.
- Push the ON/OFF button.
- Read the gross weight (the weight of the resident + the weight of the sling) on the display.
To get the net weight, weigh the sling and subtract that weight from the gross weight.
Method B.
How to start weighing before placing the resident or the sling:
- Push the ON/OFF. button
- Wait about 10 seconds until 0.0 kg/ lbs are shown on the display..
- Place the resident in the sling on the lift.
- Raise the lift so the sling with the resident is clear of the floor, bed, etc.
- Read the gross weight (the weight of the resident + the weight of the sling) on the display.
Method C.
How to weigh the resident without counting the sling weight:
- Push the ON/OFF. button
- Wait about 10 seconds until 0.0 kg/lbs are shown on the display.
- Put the sling in place, clear of the floor, bed, etc., and push the button G/N. The weight of the sling is now tared away and the display shows a Net 0.0 kg/lbs
- Place the resident in the sling on the lift.
- Raise the lift so the sling with the resident is clear of the floor, bed, etc.
Read the net weight (the weight of the resident) on the display.
Switching off
| Press the ON/OFF button to switch off the scale.
The scale has an automatic SHUT OFF after approximately 1 minute.
---|---
Error messages
| Scale overloaded
Please comply with the nominal (rated) load for the scale (see dentification
plate on the back of the device). Switch OFF and ON again.
---|---
| Underload
Switch OFF and ON again.
| Battery status
The batteries are flat and must be replaced
Cleaning instructions
Just wipe gently with a damp, and do not use any abrasive or caustic cleaning.
CAUTION
Avoid water directly on the scale.
Changing batteries
If the battery symbol is visible on the display, the batteries should be replaced as soon as possible.
Labels and indicators
On the data label, you will find the following information:
- standard approval certificate no.
- Article number
- d = actual scale division
- e = verified scale division
- d = e = 100 g.
- Range; 2 – 200 kg
Verification labels
After verification, the following label are to be found on the scale: (The
marking in some countries could be different depending on local regulations)
- CE; EC mark of conformity
- Green M; Initial verification has already been performed on this device
- HBM sealing; During the initial verification, this seal is used to protect scales of Accuracy Class III from unauthorized influence being exerted on the metrological data. If the seal is violated, the verification is no longer valid. The scales may then no longer be used for legal-for-trade operations.
This scale fulfills the regulations of EN 501/OIML R76-1. The certification is according to the Council Directive 90/384 EEC, Non-automatic Weighing Instrument Directive.
Technical specifications
| Accuracy class according to OIML R76 | 1 | C2 |
|---|---|---|
| Maximum number of scale intervals | d= e | 2000 |
| Maximum capacity (E max) | kg | 200 |
| Minimum capacity | kg | 2 |
| Minimum verification interval (e) | g | 100 |
| Display | 5 digits | |
| Battery | 4 x AA cells | |
| Battery life (AAcell with 1600 mAh) | h | 270 |
| Battery voltage | V | 3.6…6 |
| Current consumption, active mode | mA | <6 |
| Quiescent current, stand-by mode | mA | <0.001 |
| Nominal temperature range | ºC/°F | -10 to +40 / +14 to +104 |
| Operating temperature range | ºC/°F | -20 to+60 / -4 to +140 |
| Storage temperature range | ºC/°F | -40 to+85 / -40 to +185 |
| Dimensions (W x H x D) -scale unit | mm | 165 x 87 x 70 |
| Weight-scale unit | kg/lbs | approx. 0.7 / 1.5 |
| Protection class to DIN 40050 (IEC529) | IP 54 |
GETTING GROUP is a leading global provider of products and systems that contribute to quality enhancement and cost efficiency within healthcare and life sciences. We perate under the three brands of ArjoHuntleigh, GETINGE, and MAQUET. ArjoHuntleigh focuses on patient mobility and wound management solutions. GETTING provides solutions for infection control within healthcare and contamination prevention within life sciences. MAQUET specializes in solutions, therapies, and products for surgical interventions and intensive care.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>