tripplite N785-I01-SFP-D Industrial Gigabit Fiber to Ethernet Media Converter, RJ45/SFP User Guide
- June 5, 2024
- tripplite
Table of Contents
- Tripp lite N785-I01-SFP-D Industrial Gigabit Fiber to Ethernet Media
- Product Features
- Package Contents
- Optional Accessories
- Installation
- Wiring the Redundant Power Inputs
- LED Status Table
- DIP Switch Settings
- Specifications
- Warranty and Product Registration
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Tripp lite N785-I01-SFP-D Industrial Gigabit Fiber to Ethernet Media
Converter
Product Features
- Extends a Gigabit Ethernet connection to an open SFP port
- Industrial housing withstands a wide range of operating temperatures from -40° to 75°C
- Provides ESD, RFI and surge protection
- IP30 rating guarantees protection from tools and wires greater than 2.5 mm
- Open SFP port works with a variety of SFP transceivers
- LEDs indicate Ethernet connection and fiber link status
- DIP switches control Local Loop Back testing (LLB), Link Fault Signaling (LFS), Reserve and FX100 functions
- Link Fault Signaling (LFS) LED indicates when a cable has been severed or another cause for disruption has occurred
- Line Loop Back (LLB) tests both both copper and fiber network connections
- Auto MDI/MDI-X functionality removes the need for crossover cabling
Package Contents
- N785-I01-SFP-D Media Converter
- Terminal Block (20~57VDC)
- DIN Rail Kit
- RJ45 Cap
- SFP Cap
- Quick Start Guide
Optional Accessories
- N001-Series Cat5e Snagless Ethernet Cables
- N201-Series Cat6 Snagless Ethernet Cables
- N286-Series Transceivers
Installation
Notes:
- The following installation instructions refer to an installation in which two media converters are used.
- To avoid damage due to Electrostatic Discharge (ESD), it is recommended you handle the product while wearing an ESD wrist grounding strap or by touching a conductive surface (such as metal) to discharge any potential ESD prior to handling the product.
- Connect the RJ45 port on the media converter to your network with a user-supplied Cat5e/6 cable.
- Connect a transceiver to the open SFP port on the media converter.
- Connect fiber cabling matching the transceiver type to the transceiver’s port and to a second media converter with a matching transceiver.
- Connect the RJ45 port on the second media converter to your network device (workstation, hub, switch, etc.) using a Cat5e/6 cable.
- Connect 20~57VDC power properly to PWR and RPS (Terminal Block). Connect Alarm Relay output (ALM) to Alarm System.
Wiring the Redundant Power Inputs
You can use “Terminal Block (PWR)” for primary power and “Terminal Block (RPS)” for secondary power and to be a redundant power input. The power input diagram is as follows:
Insert the terminal block connector accessory, which includes “PWR” and “RPS,” into the terminal block receptor.
LED Status Table
LED | Status | Description |
---|---|---|
PWR (Green) | ON | Primary power is on |
PWR (Green) | OFF | Primary power is off |
or experiencing failure
RPS (Green)| ON| Redundant (secondary) power is on
RPS (Green)| OFF| Redundant (secondary) power is off
or experiencing failure
ALM (Red)| ON| Alarm for following conditions: LFS (Link Fault Signaling) or
power loss
ALM (Red)| OFF| Normal operation, no LFS alarm or power loss
RJ45
1000M (Green)| ON| Copper connection up to 1000 Mbps
1000M (Green)| OFF| Copper connection speed at 10/100 Mbps
LNK/ACT (Green)| ON
(Blinking)
| Copper port correctly linked
LNK/ACT (Green)| OFF| Copper port link failure
SFP
SFP
(Green/Amber)
| ON| Ethernet link-up
– Green: connection speed 1000 Mbps
– Amber: connection speed 100 Mbps
ON
(Blinking)
| Activity (receiving or transmitting data)
OFF| Port disconnected or link failed
DIP Switch Settings
DIP Switch Settings
Number| Label| Description
1| LLB| ON: LLB is enabled OFF: LLB is disabled
2| LFS| ON: LFS is enabled OFF: LFS is disabled
3| FX100| ON: Port 2 (SFP) speed at 100 Mbps OFF: Port 2 (SFP) speed at 1000
Mbps
ALM (Alarm) DIP Switch Settings
4| PWR| ON: Master power alarm reporting is enabled OFF: Master power alarm
reporting is disabled
5| RPS| ON: Redundant power alarm reporting is enabled OFF: Redundant power
alarm reporting is disabled
6| LFS| ON: Alarm for LFS issue is triggered OFF: Alarm LFS is disabled
Link Fault Signaling (LFS)
When the LFS DIP switch is enabled (#6), an alarm indicator will illuminate to indicate when a cable has been severed or when some other cause of disruption in service has occurred. The LFS function monitors both copper and fiber segments for a total service report.
Line Loop Back Test (LLB)
Set DIP Switch 1 to “ON” to activate the LLB diagnostic test function. Use the
LLB function to check if the copper and fiber and fiber segments are connected
properly.
Specifications
Specification | N785-I01-SFP-D |
---|---|
Network Speed | 10/100/1000 Mbps (Gigabit) |
Duplex Mode | Auto MDI/MDI-X |
IEEE Standards Supported | 802.3 10Base-T 802.3u 100Base-TX/FX 802.3ab |
1000Base-T
802.3z 1000Base-SX/LX
802.3x Flow Control
802.3 Auto-Negotiation
Power Consumption| 6W
Power Supply Input| 20~57VDC (Terminal Block)
Operating Temperature| -40° to 167°F (-40° to 75°C)
Storage Temperature| -40° to 185°F (-40° to 85°C)
Operating Humidity| 10% to 95% RH, Non-Condensing
Storage Humidity| 5% to 95% RH, Non-Condensing
Unit Dimensions (H x W x D)| 2 x 4.7 x 4.1 in. / 5 x 12 x 10.4 cm
Warranty and Product Registration
2-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable
instructions, to be free from original defects in material and workmanship for
a period of two (2) years from the date of initial purchase. If the product
should prove defective in material or workmanship within that period, Seller
will repair or replace the product, at its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM
ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER
THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED
BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET
FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an
implied warranty lasts, and some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal
rights, and you may have other rights which vary from jurisdiction to
jurisdiction.)
WARNING: The individual user should take care to determine prior to use
whether this device is suitable, adequate or safe for the use intended. Since
individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these
devices for any specific application.
Product Registration
Visit tripplite.com/warranty today to
register your new Tripp Lite product. You’ll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!
No purchase necessary. Void where prohibited. Some restrictions apply. See the website for details.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite, they are entitled to:
- Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
- Send the new equipment back for recycling when this ultimately becomes waste
Use of this equipment in life support applications where the failure of this
equipment can reasonably
be expected to cause the failure of the life support equipment or to
significantly affect its safety or effectiveness is not recommended.
Tripp Lite has a policy of continuous improvement. Specifications are subject
to change without notice. Photos and illustrations may differ slightly from
actual products.
WARRANTY REGISTRATION
Register your product today and be automatically entered to win an ISOBAR®
surge protector in our monthly drawing!
tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support Copyright © 2022 Tripp Lite. All rights reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>