Havit HV3270T-BLK-12V Taso step Light Installation Guide
- June 5, 2024
- havit
Table of Contents
Havit HV3270T-BLK-12V Taso step Light
Product Specifications
Product Specifications
Model No.| HV3270T-BLK-12V| HV3270T-SLV-12V| HV3270T-WHT-12V| HV3271T-BLK-12V|
HV3271T-SLV-12V| HV3271T-WHT-12V| HV3272T-BLK-12V| HV3272T-SLV-12V| HV3272T-
WHT-12V
Name| Taso
Material| Aluminium
Colour| Black| Silver| White| Black| Silver| White| Black| Silver| White
IP Rating| IP54
Input Voltage| 12v DC
Protection Class| (Low Voltage)
Lamp Base| Built in LED
Lamp Wattage| 1x 3.5w| 1x 6w| 1x 10w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 180lm, 190lm, 200lm| 350lm, 360lm, 370lm| 600lm, 625lm, 650lm
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 3 Years Replacement*
Dimensions
Important Safety Issues
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- Aluminium and 304SS fittings must not be installed within 5km of any salt water environments.
- All o-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Steps for Installation
- Make sure that the electrical circuit is free of voltage (master switch off )
- Loosen allen screws on side of fitting and remove face and set aside.
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive lined heat shrink or gel cap to make connection watertight. Failure to do this will void warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Install base plate to wall in desired location, Seal all holes including Cable entry and mounting screws.
- Fitting is preset to 3000k, To change colour temperature slide switch located on top of PCB to desired colour temperature.
- Reattach face to base plate making sure allen screws are tight to avoid water penetration
- Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Contact Details
- 143 Beauchamp Road Matraville NSW 2036 Australia
- Tel: 02 9381 8300
- Fax: 02 9666 8881
- Email: sales@havit.com.au
- Web: www.havit.com.au.
- Warranty Terms & Conditions
- Additional Information
Documents / Resources
|
Havit HV3270T-BLK-12V Taso step
Light
[pdf] Installation Guide
HV3270T-BLK-12V Taso step Light, HV3270T-BLK-12V, Taso step Light, step Light,
HV3270T-SLV-12V, HV3270T-WHT-12V
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>