HAVIT HV3281 Occhio Step Light Instruction Manual
- June 5, 2024
- havit
Table of Contents
HAVIT HV3281 Occhio Step Light
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- When installing brass fittings, gloves must be worn to avoid any oils transferring to fitting.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
- All o-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Occhio Step Light Installation Instructions
Product Specifications
Model No.| HV3281C-SS316| HV3281W-SS316| HV3281C-AB| HV3281W-AB| HV3281C-BR|
HV3281W-BR| HV3281C-BLK| HV3281W-BLK| HV3281C-WHT| HV3281W-WHT| HV3281C-
PSS316| HV3281W-PSS316
Name| Occhio
Material| 316 Stainless Steel
Colour| Stainless Steel| Antique Brass| Brass| Black| White| Polished
Stainless Steel
IP Rating| IP65
Input Voltage| 12v DC
Protection Class| (Low Voltage)
Lamp Base| Built in LED
Lamp Wattage| 1x 3w
Colour Temp| 5500k| 3000k| 5500k| 3000k| 5500k| 3000k| 5500k| 3000k| 5500k|
3000k| 5500k| 3000k
Lumens| 255lm| 240lm| 255lm| 240lm| 255lm| 240lm| 255lm| 240lm| 255lm| 240lm|
255lm| 240lm
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 3 Years Replacement*
Steps for Installation:
- Make sure that the electrical circuit is free of voltage (master switch off )
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable – If more than one fitting installed, wiring must be done in parallel.
- Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Install fitting in desired location.
- Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au Web: www.havit.com.au
**Warranty Terms & Conditions***
Additional Information
Documents / Resources
|
HAVIT HV3281 Occhio Step
Light
[pdf] Instruction Manual
HV3281, Occhio Step Light, HV3281 Occhio Step Light, Step Light, Light
---|---