HAVIT HV3278 Shim Step Light Instruction Manual
- June 5, 2024
- havit
Table of Contents
HAVIT HV3278 Shim Step Light
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- Aluminium and 304SS fittings must not be installed within 5km of any salt water environments.
- All o-rings and seals must be in place correctly to maintain warranty.
- These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.
Shim Step Light Installation Instructions
Product Specifications
Model No.| HV3278T-BLK-240V| HV3278T-WHT-240V| HV3279T-BLK-240V| HV3279T-WHT-
240V| HV3278T-BLK-12V| HV3278T-WHT-12V| HV3279T-BLK-12V| HV3279T-WHT-12V
Name| Shim
Material| Aluminium
Colour| Black| White| Black| White| Black| White| Black| White
IP Rating| IP54
Input Voltage| 240v AC| | | | 12v DC
Protection Class| (Requires Earth)| (Low Voltage)
Lamp Base| Built in LED
Lamp Wattage| 1x 12w| 1x 14w| 1x 12w| 1x 14w
Colour Temp| TRI Colour – 3000k, 4000k, 5500k
Lumens| 960lm, 1020lm, 1080lm| 1120lm, 1150lm, 1190lm| 960lm, 1020lm, 1080lm|
1120lm, 1150lm, 1190lm
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 3 Years Replacement*
Steps for Installation:
- Make sure that the electrical circuit is free of voltage (master switch off )
- Loosen allen screws on side of fitting and remove face and set aside.
- Install base plate to wall in desired location, Seal all holes including Cable entry and Mounting screws
- 240v Models, use wire with earth; connect the earth first, then live and neutral wire
- 12v DC Models – Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- Connect the cable – If more than one fitting installed, wiring must be done in parallel.
- Fitting is preset to 3000k, to change slide switch to desired colour temperature.
- Reattach face to base plate making sure allen screws are tight to avoid water penetration
- Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
Contact Details:
143 Beauchamp Road Matraville NSW 2036 Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au Web: www.havit.com.au
**Warranty Terms & Conditions***
Additional Information
Documents / Resources
|
HAVIT HV3278 Shim Step
Light
[pdf] Instruction Manual
HV3278, Shim Step Light, HV3278 Shim Step Light, Step Light, Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>