Havit HV3205 Reces Recessed Step Light Installation Guide
- June 5, 2024
- havit
Table of Contents
HV3205 Recess Recessed Step Light
Installation Guide
Recess Recessed Step Light Installation Instructions
Product Specifications
Model No.| HV3205W-SS316| HV3205W-BLK| HV3205W-WHT| HV3205N-SS316| HV3205N-
BLK| HV3205N-WHT| HV3205C-55316| HV3205C-BLK| HV3205C-WHT
---|---|---|---|---|---|---|---|---|---
HV3215W-55316| HV3215W-BLK| HV3215W-WHT| HV3215N-SS316| HV3215N-BLK| HV3215N-
WHT| HV3215C-55316| HV3215C-BLK| HV3215C-WHT
Name| Races
Material| 316StainlessSteel| Aluminum| 316StainlessSteel| Aluminum|
316StainlessSteel| Aluminum
Colour| Stainless Steel| Black| White| Stainless Steel| Black| White|
StainlessSteel| Black| White
IP Rating| IP67
Input Voltage| 12y DC
Lamp Base| Built-in LED
LampWattage| 1x 3w
Colour Temp| 3000k| 4000k| 5500k
Lumens| 1801m| 1851m| 190Im
CRI| > 80
Wiring| Parallel
Dimmable| No
Warranty| 3 Years Replacement*
HV3205 Dimensions
HV3215 Dimensions
Important Safety Issues:
- This product must be installed by a qualified electrician according to AS/NZS 3000.
- Ensure all electrical mains are disconnected before any installation.
- Modification of this product will void any warranty.
- Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
- When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
- Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
- All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on the fitting. (Warranty does not cover Tea Staining)
- Aluminum and 304SS fittings must not be installed within 5km of any saltwater environments.
- All o-rings and seals must be in place correctly to maintain the warranty.
- These instructions may be updated at any time due to product improvements, Please visit the website for the most current installation instructions.
Steps for Installation:
- Make sure that the electrical circuit is free of voltage (master switch off )
- Make a hole where the fitting is to be placed using dimensions provided on line drawings,
- Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
- If installing into concrete, insert the canister making sure it is flush with the wall.
- Connect the cable – If more than one fitting is installed, wiring must be done in parallel.
- Strip back the cable on both fitting and cable run and twist the positive cables together. Then connect neutral cables together
- Solder all joins using solder and either a heat gun or butane gas torch.
- Cover connections using an adhesive-lined heat shrink or gel cap to make the connection watertight. Failure to do this will void the warranty.
- Heat the heat shrink or crimp the gel cap making sure all connections are covered.
- Insert fitting into hole or canister pushin on clips and inserting into position
- If installed outside, apply silicon around the edge of the fitting to prevent any water from getting inside to electrical connections.
- All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.
Must be installed by a licensed electrician
*Warranty Terms & Conditions
Additional Information
**
|
---|---
https://havit.com.au/pages/warranty-terms-and-conditions|
https://havit.com.au/
Contact Details:
143 Beauchamp Road
Matraville NSW 2036
Australia
Tel: 02 9381 8300
Fax: 02 9666 8881
Email: sales@havit.com.au
Web: www.havit.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>