YINGFENG Beam 230 Moving Head User Manual

BEAM 230
MOVING HEAD

User Manual

Open-package inspection

First of all, thank you for buying our products. Please read this user manual completely and carefully, and keep it well for reference when needed. This user manual includes important information about the installation and use of the moving head. Please hew to the relevant specification strictly when installing and using this product.
This Moving headlight is made of new high-strength heat-resistant engineering plastic and cast aluminum shell, with a beautiful design and smooth outlook, Is representative of
modern lights. This product is strictly according to CE standard design and production and fully complies with the international standard DMX 512 protocol. Can be single control, also can use integrated with each other. It is suitable for large-scale theatrical performances, theaters, studios and discos, and other places. After receiving the product, please be careful to take and put., Check if the product has been damaged during transportation, and check the following parts:
The body————————————-1pcs
Safe rope————————–1pcs
Power cable ———————————-1pcs
hook——————————2pcs
User manual ——————————– -1psc
signal cable———————–1pcs

Attentions

1. To ensure the service life of the product, please keep it away from water and do not work in an environment in which the temperature is above sixty degrees.
2. Don’t put the product in a place easy to lose or easy vibration.
3. In order to avoid electric shock, this product must maintenance by a professional person.
4. when using, the power supply voltage change should not be more than 10%, the voltage is too high, will shorten the life of the light bulb, the voltage is too low, then affects the light color.
5. When powered off, the product needs 20 minutes for sufficient cooling before use again.
6. To ensure normal use, please read this user manual carefully.

Technical Parameter

1. Voltage： AC100V-240V
2. Frequency：50/60Hz
3. Rated power：350W/400W
4. Lamp：5R Philips/7R Osram
5. Bulb power：189W/230W
6. Strobe：1-13times/second
7. Color temperature：8000K
8. Horizontal scanning 540 degrees, Horizontal 16 bit, electronic error correction, vertical scanning 270 degrees, vertical 16 bit, electronic error correction.
9. Gobo：17 gobo add white and stream effect, gobo electric focus function
10. Color：14 color adds a white and rainbow effect
11. Effect： Can transfer from the beam into atomization effect
12. Panel Control： Touch screen control and Manual control
13.  Signal Control： DMX512 international standard signal
14. Safety protection: when the machine is overheating or the system malfunctioning it will automatically cut off power supply.

Installation

1. Before installation, please make sure the power supply is the same as the product identified.
2. The cable connecting to the main power supply must meet the requirements, and should not overload.
3. The installation must be done by a professional person, fixed the light safely and reliably, and transferred to the appropriate irradiation angle.
4. Please ensure that the draft fan and exhaust channel are not blocked
5. At the bottom of the moving headlight with the insurance line connection hole, based on safety reasons, please use the insurance rope which can withstand ten times the weight of the Moving head through the insurance line connection hole for auxiliary lifting.
6. When installing this equipment, please ensure that at least 1.5 meters range of no extreme inflammable and explosive items(ornaments, etc.) ensure the moving headlight and the wall interval twenty centimeters above.
7. This product can be fixed hanging installation and put on the floor to use.
8. Based on safety, please make sure the earth wire is grounded.
9. The Pan and Tilt of this product was locked when packing, please ensure it was unlocked before the power on.

Installation and change of the Lamp

1. In order to prolong the life of the moving headlight as far as possible, please choose the same type of lamp for it.
2. First of all to unscrew the four screws on the back cover of the moving headlight, then open the back cover, pinch the ceramic holder of the bulb and anti-clockwise rotation 90°， and take out the lamp.
3. Open the bulb packing carefully, take out the new lamp, pinch the lamp ceramic holder, insert the lamp holder, and 90°clockwise rotation

The connecting of the signal cable

Connected the XLR control cable from the DMX controller’s outlet to the first moving headlight’s input port, and connected from the first light’s DMX outlet to the second light’s DMX input port, repeating the process, until all the lights are of connection. Then connected the accompanied circuit plug to the last light’s signal output port, the connection finished, as shown in the figure:

Note: please remember to connect a circuit plug to the last moving headlight’s signal output port. Between the second and third poles of the CANON plug of this circuit, plug have a 120Ω resistance, connecting this circuit plug can avoid signal reflection phenomenon during the
DMX512 signal transmission process.
This Moving head use 3 pin XLR plug, If your controller use 5 pin XLR plug, you must use a 5-pin to 3 pin patch cord. See below:

Button Instruction

The “LEFT”, “RIGHT” buttons have the same function:
Return to the last interface
“UP”, and “DOWN” button:
Select, Edit
“ENTER” button (the “OK”button):

Executive function and start editing, exit editor

Below take “modify DMX address code” as an example, tell the use of the button:

1. If the current is not the main interface, press the “LEFT” button(one or multiple) can come back to the main interface.
2. In the main interface, press the “UP” button of the “DOWN” button and select the “set” button
3. Press “ENTER” button, come to the “setting” interface
4. In the “set” interface, press the “UP” or” DOWN” button and select “DMX ADD”
5. Press the “ENTER” button to come to the editing state
6. Press the “UP” or “DOWN” button to modify the DMX address code.
7. Press the “ENTER”button quit the editing stage.
   If use touch scree, the process is more convenient:

1. In the main interface touch the “set” button, come to the “setting” interface
2. The same to the up 4~7 step(can use both physical button and touch button), with no more words.

Interface introduction

9.1. Main interface

The 3 buttons at top right corner are for language switching and screen rotation. The function of the 4 buttons on the bottom row please see the following info.
9.2.Interface Settings

controller or Master.
**** Auto| Master State： Autorun， and sending DMX signal to Slave.
Notice： If the bulb off, the light will not be on automatically; if you need to observe the lighting effects, please turn on the bulb light first, then enter the automatic state.
**** DMX Address| **** 1-512| Press the “OK” button to enter the edit state. at the same time, choose the hundreds place, and change the address code according to the“UP” and” DOWN” buttons.
Click” OK” again to select tens to edit, and then click” OK” again to select Units to edit. Click again to exit.
Channel Model| 16| The 17th to 20th channel is invalid
20| The 17th   to 20th   channel control function (see channel table)
Pan reversal| off|
| on|
---|---|---
Tilt reversal| off|
on|
Pan and Tilt    exchange| off|
on| Exchange XY channels(including fine turning)
Pan and Tilt encoder| On| Use an encoder (light coupling) to judge the wrong

step and correct it automatically.

off| Not use an encoder(light coupling) to correct the position
Without DMX Signal| retain| Keep the original state to continue running
clear| Motor returns, and stops running
Screen saver| on| 30 seconds later, it will close the backlight
off| Backlight on forever

Boot light bubble

| off| reset directly after Power on, if not, need to use the menu or control table to turn it on manually.
on| Light on automatic after power on, and can not reset until the light bulb is on successfully
**** Restore default settings| | Click the “OK” button to see the confirmation dialog box, then click the “OK” button again to restore default settings.

9.3.Information interface

displayed channel value for reference.
System error record| If the red light” ERR” shine, it indicates the operational error of lamps and lanterns, the details please check in the sub- interface.
After the check, you can click the “OK” button to empty the error record.

9.4.Manual control interface

again, then enter reset interface, then after all motor reset.
Color wheel| 0-255| Press the “OK” button to enter the edit state. at the same time, choose
。。。| 0-255| the hundreds to change channel value according to the “UP” and “DOWN” buttons. Click” OK” again to select tens to edit, and then click” OK” again to select  Units to edit. Click again to exit.
---|---|---
Gobo wheel speed| 0-255
Lamp control| on|
off|

Channels

channel

| Channel mode

16                                                         20

---|---
|
1| Color wheel| Color wheel
2| Blackout / Strobe| Blackout / Strobe
3| Dimmer| Dimmer
4| Gobo wheel| Gobo wheel
5| Prism| Prism
6| Prism rotation| Prism rotation
7| Macro| Macro
8| Frost| Frost
9| Focus| Focus
10| Pan| Pan
11| Pan fine| Pan fine
12| Tilt| Tilt
13| Tilt fine| Tilt fine
14| Pan and Tilt speed| Pan and Tilt speed
15| Reset| Reset
16| Lamp control| Lamp control
17| | Blank
18| | Color wheel speed
19| | Dimming, Prism, and Atomization speed
20| | Gobo wheel speed

Problems and Solutions:

the set of digital address codes and the connectivity of the control signal
The projected image has a halo| Check the electronic focusing channel value to see whether it is right for the current distance of projection
The Beam light is not bright enough| Maybe the end-of-life of the bulb, change a new one, and check whether the optical component is clean.

Note: the other maintenance work shall be conducted by a qualified professional personage.

Maintenance

1. Keep dry, and avoid working in damp conditions.
2. Intermittent use can effectively prolong the service life of the lamps.
3. In order to obtain good ventilation effects and lighting effects, you’d better clean the fan, fan nets, and lens often.
4. Do not use organic solvent such as alcohol..to wipe the lamps shell, it may cause some damage.

Statement

This product was in good performance condition and completely packed before delivery. All users should strictly abide by the above statement warnings and instructions. Any damage caused by misuse is not within the company warranty, and the company will not be responsible for the cause of damage because of the operator’s ignorance of this user manual.

Guangzhou Yingfeng Lighting Equipment Co., Ltd
www.yf-light.com

Documents / Resources

| YINGFENG Beam 230 Moving Head [pdf] User Manual
Beam 230 Moving Head, Beam 230, Moving Head, Head
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>