CycevSun DOCL4024WCCT 2.4G Remote LED Ceiling Light Instruction Manual
- June 5, 2024
- CycevSun
Table of Contents
2.4G REMOTE
LED CEILING LIGHT
Specifications
| Voltage | 110-240Vac, 60Hz |
|---|---|
| Certification | ETL ,FCC |
| Power | 18W(Equal 150W Incandescent) |
| Lumen | 1800LM |
| Lifetime | Over30,000hours |
| Size | φ 11.8.0.98 INCH |
Installation Instruction
REMOTE-LED CEILING LIGHT
Size| 12inch| 15.8inch| 20inch
Watt| 18W| 24W| 30W
Voltage| 120V
Dimmable| 5%-100%
Color empemWm| 3000K-5000K Changing
Lumen| 1800LM| 2400LM| 3000LM
Lifetime| 30,000 hours
Material| VO fireproof ABS plastic
Certification| FCC
Warranty| 3 Years Warranty
Safety notice
- Please do not exceed the rated range of the power supply (120V±101,60Hz);
- Do not install on unstable or inclined ceiling surfaces to avoid falling off;
- Lamps cannot be covered by heat insulation pads or similar materials;
- Before maintenance and installation, please confirm that the power supply has been cut off and operated by a professional electrician;
- Ceiling lamps will generate heat during operation. Do not use in high temperature and humidity environments;
- When the lamp is abnormal, be sure to cut off the power firstly and contact the dealer;
- Do not disassemble or modify the lamp by yourself to avoid sudden accidents.
Open the package, unpack the blister film, take out the ceiling lamp and the accessories, remove the warning sticker, and rotate to remove the ceiling cover.
Please entrust electrical professionals to install or overhaul to avoid
danger.
Before installation, be sure to cut off the power to avoid electric shock.
When installing, it shall strictly follow the steps shown in the manual
improper installation may cause fire, electric shock, or falling of the lamp
body.
Product Introduction
Check if the two mounting points of the lamp box are complete without damage
or not After the determination is complete, fix the ceiling cover through the
hanging cable to the light box with metric screws.| Hook the ceiling light
body with a hanging cable, which one person can easily install.
---|---
|
Attach white to white, black to black, and ground to ground wires using a wire
connector then put the wires into the junction box.| Move the lamp body to
embed the ceiling cover into the lamp body then rotate the lamp body
counterclockwise. and ensure that the installation is firm.
|
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.