Hunter 2612244 Xidane Five Light Linear Chandelier Instruction Manual
- June 5, 2024
- Hunter
Table of Contents
Hunter 2612244 Xidane Five Light Linear Chandelier Instruction Manual
For Models: 19747, 19748
Here are the tools you’ll need to complete your installation:
Fixture weight ±2 lbs:
Peso ±2 lb:
Poids fixe ±2 lbs:
8.8 lbs (4 kg)
Hardware Service Kit
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture.
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Put the drywall anchor (C) into the hole in the ceiling. Place mounting plate (D) over the junction box so that mounting screws (B) and nuts (S) extend out away from the ceiling. Pull the house wires through the center of the mounting plate (D). Secure the mounting plate (D) to the junction box by tightening screws (F) then insert the drywall screw (E) through the mounting plate (D) into the drywall anchor (C).
ASSEMBLING THE FIXTURE
There are 4 12-inch rods (O), and 1 6-inch rod (N) included for each side of
the fixture. Determine the correct number of rods needed for proper hanging
height. To lengthen the fixture, add additional rods. To shorten the fixture,
trim the wires to desired length. Leave at least 8 to 10 inches of wire in
addition to the desired length and slide any excess rods off the fixture’s
wiring to discard. Keep in mind that you must use at least one rod to hang the
fixture on each
side. Thread the wires through the rods and pull the wires until taut before
connecting the rods together (do not overtighten). Screw the lower end of rod
onto threaded post (T) of the fixture. Place the reinforcing plate (K) inside
the canopy (L) and place the canopy (L) over the threaded post (N) of the rod.
Put the center of the threaded post (N) through the wirerope loop (J) and
washer (I). Lock reinforcing plate and canopy with hex nut (H) on threaded
post (N). Hide the wirerope (J) inside the canopy. Secure the screw collar
loop (A) to the mounting plate (D).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (G) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.
FINISHING THE INSTALLATION
Raise canopy (L) to mounting plate (D) and position mounting screws (B) so that they protrude through the openings of canopy (L). Secure canopy (L) in place with cap nuts (M). Then use the socket ring (R) to secure the glass shade (Q) to each socket. Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
NOTICE:
Drill 9/64″ pilot holes in support structure to aid in securing light fixture.
NOTICE
In order to use a 12in rod by itself you must first remove the post from the
6in rod and install it on one of the ends of the 12in rod.
Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the downrods. Threaded post may also be removed for easier wire access.
Read More About This Manual & Download PDF: