Enders Madeira Infrared Heater Instruction Manual

INSTRUCTION MANUAL Model no.: Madeira
ASSEMBLE & OPERATION INSTRUCTION
Please read carefully and Save this instruction for future reference

Introduction

The infrared heater contains a halogen-formed reflector heating system that provides even heat distribution.
The infrared heater saves 30%-40% of electricity in comparison to traditional heaters. The infrared heater is commonly used for outdoor heating.

CAUTION: FOR OUTDOOR USE ONLY

Warning

READ CAREFULLY-The infrared heater is designed for safe operation. Nevertheless, installation, maintenance, and operation of the heater can be dangerous. Observing the following procedures will reduce the risk of fire, electric shock, or injury to the person and keep installation time to a minimum. Save these instructions for future use.

1. Read all instructions before using this heater.
2. Remove the unit from its packaging and check to make sure it is in good condition before using it.
3. Do not let children play with parts of the package (such as plastic bags)
4. Check the household voltage to ensure it matches the heater’s rated specification.
5. Check the power cord and plug carefully before using, to make sure that they are not damaged.
6. Before unplugging the power cord, be sure to turn off the power, when energizing the unit, be sure your hands are dry to prevent electric shock.
7. Do not use flammable objects near the heater or point the heater directly towards furniture, or pillows. bedding, paper, clothes, and curtains. Make sure they are at least 3 feet (1 meter) from the front of the heater and keep the sides and rear clear of any objects.
8. Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid
9. To protect against electric shock, do not immerse the cord or plug in water or any other liquid.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the heater.
11. Always unplug the heater when not in use.
12. Do not allow the cord to overhang the countertop where it can be easily pulled by children.
13. Do not put fingers or foreign objects into the grill while in operation.
14. Do not leave the appliance unattended when in use.
15. This heater is not intended for use in bathrooms, laundry, and similar indoor locations, never located the heater where it may fall into a bathtub or other water container.
16. No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling.
17. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children and vulnerable people should be supervised to ensure they do not play with the appliance.
18. If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
19. To prevent overheating of this appliance, keep the air inlets and outlets clean and free of anything that may cause blockage. Check all inlets and outlets from time to time to ensure it is clear of any dirt or dust accumulation.
20. Parts of the heater may exceed 200 ℃. Contact with the heating tube, reflector, or metal parts near the heating tube, may cause severe BURNS. To avoid burns, do not let bare skin touch hot surfaces.
21. ALWAYS allow the heating element to cool at least 10 minutes before touching the heating tube or any adjacent part.
22. This product contains recyclable materials. Do not dispose of this product as unsorted municipal waste. Please contact your local municipality for the nearest collection point.

WARNING: HOT SURFACE, DO NOT TOUCH, DO NOT COVER CORRECT INSTRUCTIONS

Correct Installation Position – o1

Note: Mounted angle with 30º – 45º

Correct Installation Position – 02

Note: The heater should be wall or ceiling mounted under well pro- tected environments, at least keep 3 feet (0.9m) away from any combustible objects.

Note: Do not cover.

Warning – to reduce the risk of fire

Caution: Keep combustible materials, such as furniture, pillows, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
|  Caution: Do NOT use with an extension cord or relocatable power tap (out- let/power strip).

Caution: Hotsurface, do NOT cover with| Caution: Do NOT touch. any objects such as blanket on the heater.

ASSEMBLY INSTRUCTIONS

Installation Accessoles :

Tools Needed:

• Pencil Hammer Level Screw Driver Power Drill and drill bit A wall mounting bracket is provided with the heater which has been specifically designed to allow this product to be fitted to a wall or ceiling. Before drilling the holders, ensure the wall/ceiling is solid and that there are no hidden water pipes or electric wires. The heater must be installed no less than 16’’ from the side walls and no less than 6”’ off the floor.

Important: Ensure that the supply cables are well mounted and that they do not come into contact with reflector of the heater or that is does not cross the heated area. The  supply cable can be fixed to the metal mounting bracket behind the heater with plastic zip ties.

The heater must be installed at least 2.4 M above the floor Wall mounted

Ceiling mounted

Attention:
Digital display position should be on left for correct installation direction

FUNCTION & OPERATION

1. PLUG the unit into a plug socket, make sure the power supply is the same as rated
2. PRESS the power button on the right side of heater
3. TURN ON the heater via the remote control of the button on the side of the heater
4. DOWN & UP BUTTON, set the power level

OPERATION BY REMOTE CONTROLLER
The heater is operated from the remote control supplied. Insert 2 x AAA Alkaline batteries into the remote control. ****

1. POWER BUTTON: Turns heater on or off.
2. UP BUTTON: Increases the temperature and timer level.
3. DOWN BUTTON: Decreases temperature and timer level.
4. LEVEL BUTTON: Used to adjust heat levels (L1-L2). Press the level button, then use the up and down buttons (2 and 3) to increase or decrease the heating level.
5. TIMER BUTTON: Use to set the timer from 0H– 24H(0-24 hours).
   Adjust using buttons 2 & 3 to the number of hours you would like to set.

The heater remote controls have the same frequency, so it is possible to control several heaters with just one remote.

CLEANING AND MAINTENANCE

Regular and careful cleaning helps your infrared heater operate efficiently for many trouble free years. To clean your heater follow steps below
Unplug the power cord for your safety before cleaning your appliance.

1. Make sure the heater is cool before continuing.
2. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. (CAUTION: DO NOT let liquids enter the heater)
3. DO NOT use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
4. DO NOT immerse the heater in water. 5. Wait until the heater is completely dry before use. Storage: Store the heater in a cool, dry location when not in use to prevent dust and dirt build up. Use packaging carton to store.

Troubleshooting

1. If the heater will not turn on, check if the power cord is plugged into an electrical outlet, if not, plug in.
2.  Check your electricity to ensure the main fuse is working.
3.  Check to see it the thermostat knob is turned to the ON position.
4. Check the thermostat setting. The heater may be off because it has reached the desired temperature setting.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>