HUNTER 19522 Sunjai 5 Light Chandelier User Manual
- June 4, 2024
- Hunter
Table of Contents
HUNTER 19522 Sunjai 5 Light Chandelier User Manual
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning installation of the
lighting fixture.
Here are the tools you’ll need to complete your installation:
Ladder
**Screwdriver
**
Pliers
Wire Strippers
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the ceiling,
including the old mounting bracket. Remove the new mounting bracket assembly
from the bag. One end of the threaded post (D) should be attached to the
mounting bracket (A) with a hex nut (E) in place. The other end should have
the canopy loop (G) attached. Unscrew the canopy loop ring (H) from the canopy
loop (G). Depending on the placement of your junction box the position of
threaded post (D) may need to be adjusted to allow the canopy to be flush with
the ceiling. Determine this by lifting mounting bracket (A) up to the junction
box and place canopy (F) over the canopy loop (G), so that it is flush with
the ceiling. Adjust the position of threaded post (D) on the mounting bracket
(A) so that the canopy (F) covers at least half of the exterior threads on the
canopy loop (G) while it is securely connected to threaded post (D). The
threaded post (D) can be adjusted by loosening hex nut (E) to allow movement
of threaded post (D) on mounting bracket (A). Once the ideal position of the
threaded post (D) is determined, tighten up the hex nut (E) onto the threaded
post (D) just beneath the mounting bracket (A) to secure the threaded post in
place.
ASSEMBLING THE FIXTURE
Thread wires through and screw the rod with top loop (K) onto the threaded
post (L) of the fixture. By measuring, determine the correct number of chain
links needed for proper hanging height. If necessary, use a pair of pliers to
open and remove any excess chain. Attach one quick-connect link (J) to each
end of chain (I). Use one quick-connect link (J) to attach chain (I) to
hanging ring (K) and securely close. Feed the fixture wires up through the
chain (every three links or so), pulling the wires until taut. Slide canopy
loop ring (H) and canopy (F) onto the chain/wire and thread wires through
canopy loop (G) and threaded post (D). Use the remaining quick-connect link
(J) to attach chain (I) to canopy loop (G). To shorten the fixture, trim the
wires to desired length. Leave at least 8 to 10 inches of wire in addition to
the desired length. Have a helper support the fixture’s weight and attach the
mounting bracket (A) to the junction box by securely tightening the mounting
screws (C).
CONNECTING THE WIRES
Attach the fixture’s wires to the power supply wires from the junction box.
Connect black to black (Live); white to white (grounded); grounding to
grounding (green or copper). Twist the ends of the wire pairs together. Then,
twist on a wire connector. Make sure all twists are in the same direction.
Loop fixture’s ground wire around grounding screw (E) and tighten. If there is
no ground wire (green or copper) from the junction box, contact a qualified
electrician
FINISHING THE INSTALLATION
Place the canopy (F) flush to the ceiling and slide the canopy loop ring (H) up beneath the canopy. Tightly screw canopy loop ring (H) onto the canopy loop (G) to properly secure the canopy (F) in place. Adjust the angle of the lamp arms so that they are evenly distributed (see drawing 1) and install candle finials (M). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Turn on the power and test the fixture. Your installation is now completed.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
Hunter Pro Tip:
Let the tool do the work! Use chain pliers to easily open and close chain links to shorten your fixture.
Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the down rods. Threaded post may also be removed for easier wire access.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>