Hunter 19030 Saddlewood 6 Light Chandelier Instruction Manual

Saddlewood
For Models:
19030, 19031

8 Light Chandelier

Fixture weight ±2 lbs:
Peso ±2 lb: 21.6 lbs (9.8 kg)
Poids fixe ±2 lbs:

Here are the tools you’ll need to complete your installation:

INSTALLATION INSTRUCTIONS

WARNING

• To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
• The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
• All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.

READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning the installation of the lighting fixture.

PREPARING FOR INSTALLATION

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. One end of the threaded post (F) should be attached to the mounting bracket (A) with a washer (D) and a hex nut (E) in place. The other end should have the canopy loop (G) attached. Unscrew the canopy loop ring (I) from the canopy loop (G). Depending on the placement of your junction box the position of the threaded post (F) may need to be adjusted to allow the canopy to be flush with the ceiling. Determine this by lifting mounting bracket (A) up to the junction box and placing canopy (H) over the canopy loop (G), so that it is flush with the ceiling. Adjust the position of the threaded post (F) on the mounting bracket (A) so that the canopy (H) covers at least half of the exterior threads on the canopy loop (G) while it is securely connected to the threaded post (F). The threaded post (F) can be adjusted by loosening the hex nut (E) to allow movement of the threaded post (F) on the mounting bracket (A). Once the ideal position of the threaded post (F) is determined, tighten up the hex nut (E) onto the threaded post (F) just beneath the mounting bracket (A) to secure the threaded post in place.

ASSEMBLING THE FIXTURE

Screw the threaded post (N) of rods (O) to swivels (M). Place the column according to the angles shown in inset 2.
Adjust three rods to make the hooks (P) connect with loops (Q) as shown in inset 1 (the open position of the hooks (P) should be on the inside of the fixture).
By measuring, determine the correct number of chain links needed for proper hanging height. If necessary, use a pair of pliers to open and remove any excess chain. Attach one quick-connect link (J) to each end of the chain (K). Use one quick-connect link (J) to attach chain (K) to the hanging ring (L) and securely close. Feed the fixture wires up through the chain (every three links or so), pulling the wires until taut. Slide canopy loop ring (I) and canopy (H) onto the chain/wire.
Use the remaining quick-connect link (J) to attach chain (K) to the canopy loop (G). To shorten the fixture, trim the wires to the desired length. Leave at least 8 to 10 inches of wire in addition to the desired length. Thread wires through canopy (H). Have a helper support the fixture’s weight and attach the mounting bracket (A) to the junction box by securely tightening the mounting screws (B).

CONNECTING THE WIRES

Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (Live); white to white (grounded); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Loop fixture’s ground wire around grounding screw (C) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.

FINISHING THE INSTALLATION

Place the canopy (H) flush to the ceiling and slide the canopy loop ring (I) up beneath the canopy. Tightly screw canopy loop ring (I) onto the canopy loop (G) to properly secure the canopy (H) in place. Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Your installation is now
complete. Turn on the power and test the fixture.

CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning.
For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.

Hunter Pro Tip:
Let the tool do the work! Use chain pliers to easily open and close chain links to shorten your fixture.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>