Hunter 19239 Solhaven 1 Light Mini Pendant Instruction Manual
- June 4, 2024
- Hunter
Table of Contents
Hunter 19239 Solhaven 1 Light Mini Pendant
INSTALLATION INSTRUCTIONS
WARNING
- To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
- The lighting fixture must be grounded. If the ground wire for the installation site is not present, immediately STOP installation and consult a qualified electrician.
- All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that
they are read carefully and completely before beginning the installation of
the lighting fixture.
PREPARING FOR INSTALLATION
Carefully remove all contents from the carton. Shut off the power at the
circuit breaker and completely remove the old fixture from the ceiling,
including the old mounting bracket. Remove the new mounting bracket assembly
from the bag. Remove cap nuts (H) from mounting screws (B). Place the mounting
plate (A) over the junction box so that mounting screws (B) and nuts (C)
extend out away from the ceiling. Adjust the position of mounting screws (B)
so that mounting screws (B) can be exposed 5-6 mm after passing through the
canopy (F) to properly fit the cap nuts. Depending on the placement of your
junction box the position of mounting screws (A) may need to be adjusted to
allow the canopy to be flush with the ceiling. Mounting screws (B) can be
adjusted by loosening nuts (C) and loosening or tightening mounting Once the
ideal position of mounting screws (B) has been confirmed, tighten nuts (C) on
mounting screws (B) on the front of the mounting plate to ensure that mounting
screws (B) are secure. Pull the house wires through the center of the mounting
plate (A). Secure mounting plate (A) to the junction box by tightening the
screws (D).
ASSEMBLING THE FIXTURE
There are 4 12-inch rods (K), and 1 6-inch rod (I) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture. Thread the wires through the rods and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten (some manual straightening of the downrods may be required). Screw rod onto threaded post (L) on the fixture. Pull the fixture wires through the top of the canopy. Screw the top rod to hang straight (G) of canopy (F).
CONNECTING THE WIRES
Have a helper support the fixture’s weight while completing the wiring. Attach
the fixture’s wires to the power supply wires from the junction box. Connect
black to black (Live); white to white
(grounded); grounding to grounding (green or copper). Twist the ends of the
wire pairs together. Then, twist on a wire connector. Make sure all twists are
in the same direction. Loop fixture’s ground wire around grounding screw (E)
and tighten. If there is no ground wire (green or copper) from the junction
box, contact a qualified electrician.
FINISHING THE INSTALLATION
Raise canopy (F) to mounting plate (A) and position mounting screws (B) so that they protrude through the openings of canopy (F). Secure canopy (F) in place with cap nuts (H). Pass the shade (N) over the socket as shown in the figure and lock it with washer (M). Install light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Your installation is now complete. Turn on the power and test the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the
downrods. Threaded post may also be removed for easier wire access.
NOTICE
In order to use a 12in rod by itself you must first remove the post from the
6in rod and install it on one of the ends of the 12in rod.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>